How to remove the Brake Caliper?

To remove the brake hose-to-caliper banjo fitting, first mark its position relative to the caliper and then remove the banjo bolt. Discard the old copper sealing washers and wrap a plastic bag around the hose end to prevent fluid loss and contamination. Next, remove the caliper mounting bolts and clean the caliper with brake system cleaner. Do not use kerosene or petroleum-based solvents. Place shop towels or a block of wood in the center of the caliper and use compressed air to force the piston out of the bore. Inspect the piston and caliper bore for any surface defects, replacing the piston if necessary. Pry out the piston seal and dust boot and discard them, as the overhaul kit will contain replacements. Clean the piston and cylinder bore with brake system cleaner, clean brake fluid, or denatured alcohol. Lubricate the new piston seal with clean brake fluid and position it in the cylinder groove using your fingers. For installation, install the new dust boot in the piston groove, dip the piston in clean brake fluid, and place it in the bore, depressing it to the bottom. Seat the boot in the caliper counterbore using a boot installation tool or blunt punch. Connect the brake hose to the caliper using new copper washers, aligning the union fitting with the marks made before disassembly. Finally, install the caliper, tighten the mounting bolts and brake hose fitting bolt to the specified torque, and bleed the front brake circuit.

Genuine Chevrolet S10 Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Brake Calipers found

View related parts
Chevrolet S10 Caliper Kit,Front Brake
Part Number: 18029813
$17.00 MSRP: $23.36
You Save: $6.36 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Overhaul Kit
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet S10 | CREW CAB, ELECTRIC, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper Kit,Front Brake
Part Number: 18003724
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-2003 Chevrolet S10 | 2 DOOR, 4 DOOR, ELECTRIC, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper, Front Brake (Service)
Part Number: 18029815
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper Asm,Front Brake
Part Number: 18060134
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper, Caliper Assembly
- Position: Front
- Replaces: 18016155
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-2003 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper, Front Brake (Service)
Part Number: 18029814
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper Asm,Front Brake
Part Number: 18060135
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper, Caliper Assembly
- Position: Front
- Replaces: 18016156
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-2003 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper,Front Brake(Remanufacture)
Part Number: 19132286
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaces: 18060144
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1990 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper Kit,Rear Brake
Part Number: 18026149
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Replaces: 18025476
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper Kit,Rear Brake
Part Number: 18026150
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Replaces: 18025477
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper Asm,Front Brake (Remanufacture) LH
Part Number: 19132285
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front Driver Side
- Replaces: 18060143, 18016424
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1990 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper,Front Brake
Part Number: 18029755
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chevrolet S10 | CREW CAB, ELECTRIC, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Caliper,Front Brake
Part Number: 18029754
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chevrolet S10 | CREW CAB, ELECTRIC, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L

Chevrolet S10 Brake Calipers Parts Questions & Experts Answers

Caliper Kit,Rear Brake
18026149
Q: How to remove the Brake Caliper?
A: To remove the brake hose-to-caliper banjo fitting, first mark its position relative to the caliper and then remove the banjo bolt. Discard the old copper sealing washers and wrap a plastic bag around the hose end to prevent fluid loss and contamination. Next, remove the caliper mounting bolts and clean the caliper with brake system cleaner. Do not use kerosene or petroleum-based solvents. Place shop towels or a block of wood in the center of the caliper and use compressed air to force the piston out of the bore. Inspect the piston and caliper bore for any surface defects, replacing the piston if necessary. Pry out the piston seal and dust boot and discard them, as the overhaul kit will contain replacements. Clean the piston and cylinder bore with brake system cleaner, clean brake fluid, or denatured alcohol. Lubricate the new piston seal with clean brake fluid and position it in the cylinder groove using your fingers. For installation, install the new dust boot in the piston groove, dip the piston in clean brake fluid, and place it in the bore, depressing it to the bottom. Seat the boot in the caliper counterbore using a boot installation tool or blunt punch. Connect the brake hose to the caliper using new copper washers, aligning the union fitting with the marks made before disassembly. Finally, install the caliper, tighten the mounting bolts and brake hose fitting bolt to the specified torque, and bleed the front brake circuit.