How to properly remove and install wiper arms on a Chevrolet Nova?

Make sure that the wiper arms are in the self-parked position, the motor having been switched off In the low speed mode. Note carefully the position of the wiper arm in relation to the windshield lower reveal molding. It should be approximately two inches above the molding. Using a suitable hooked tool or a small screwdriver, pull aside the small spring tang which holds the wiper arm to the splined transmission shaft and at the same time pull the arm from the shaft. Installation is a reversal of removal but do not push the arm fully home on the shaft until the alignment of the arm has been checked. If necessary, the arm can be pulled off again and turned through one or two serrations of the shaft to correct the alignment without the necessity of pulling aside the spring tang. Finally, press the arm fully home on its shaft and then wet the windshield glass and operate the motor on low speed to ensure that the arc of travel is correct.

Genuine Chevrolet Nova Wiper Arm

Windshield Wiper Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Wiper Arms found

View related parts
Chevrolet Nova Insert,Windshield Wiper Blade
Part Number: 12344997
Product Specifications
- Other Name: WIPER, Windshield Wiper Blade
- Replaces: 94841829
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1988 Chevrolet Nova | 4 DOOR, 4 DOOR NOTCHBACK, TWIN CAMSHAFT 4 DOOR | 4 Cyl 1.6L
View related parts
Chevrolet Nova Arm Assembly, W/Shield Wiper No.1
Part Number: 94841827
Product Specifications
- Other Name: ARM, Windshield Wiper Arm; Wiper Arm
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1988 Chevrolet Nova | 4 DOOR, 4 DOOR NOTCHBACK, TWIN CAMSHAFT 4 DOOR | 4 Cyl 1.6L
View related parts
Chevrolet Nova Arm Assembly, W/Shield Wiper No.2
Part Number: 94841830
Product Specifications
- Other Name: ARM, Windshield Wiper Arm; Wiper Arm
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1988 Chevrolet Nova | 4 DOOR, 4 DOOR NOTCHBACK, TWIN CAMSHAFT 4 DOOR | 4 Cyl 1.6L

Chevrolet Nova Wiper Arm

In Chevrolet Nova vehicles, the Wiper Arm has a critical function of clearing the view during precipitation, but mainly rain. In this regard, it is primarily meant to perform the task of clearing the windshield in as much as drivers need controls for safe operation. Wiper arm may wear or get damaged over time and therefore its functionality may be affected and safety too. This means that for preventing of worst-case scenarios that may come as a result of a malfunctioning of the Wiper Arm, it is advisable to replace it as soon as one notices emerging signs. However, there is no indication in the overview as to different types or styles of Wiper Arms employed for different Nova models- all the same, the focus stays on the necessity to monitor this compering to have proper driving conditions. These checks and especially the replacement should be done often to have a good ride on the vehicle and most importantly to enhance safety for the driver.

Each OEM Chevrolet Nova Wiper Arm we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Nova Wiper Arm Parts Questions & Experts Answers

Arm Assembly, W/Shield Wiper No.1
94841827
Q: How to properly remove and install wiper arms on a Chevrolet Nova?
A: Make sure that the wiper arms are in the self-parked position, the motor having been switched off In the low speed mode. Note carefully the position of the wiper arm in relation to the windshield lower reveal molding. It should be approximately two inches above the molding. Using a suitable hooked tool or a small screwdriver, pull aside the small spring tang which holds the wiper arm to the splined transmission shaft and at the same time pull the arm from the shaft. Installation is a reversal of removal but do not push the arm fully home on the shaft until the alignment of the arm has been checked. If necessary, the arm can be pulled off again and turned through one or two serrations of the shaft to correct the alignment without the necessity of pulling aside the spring tang. Finally, press the arm fully home on its shaft and then wet the windshield glass and operate the motor on low speed to ensure that the arc of travel is correct.