How to replace the CKP sensor for Chevrolet Impala and Monte Carlo?

Both V6 and V8 models have their CKP sensors placed on the back side of the engine block. When you have to drive the vehicle to a dealer, after replacing the CKP sensor and starting the engine, and let service department perform crank-shaft position variation team procedure with a factory scan tool if Malfunction Indicator Light (MIL) comes on. To replace the sensor, raise the vehicle and place it securely on jackstands. The electrical connector should be disconnected from CKP sensor. That bolt that holds CKP sensor should be removed. The old CKP sensor 0-ring should be removed and discarded thereafter. Be sure to use a new 0-ring when installing even if you are installing an old one. Just reverse what you did when removing it as far as installation is concerned. Remember to use a new 0-ring and tighten up CKP sensor mounting bolt properly. On V8 models, near flywheel is where CKP sensor is located at. Get rid of the rear exhaust manifold. Removing electrical connector while undoing the mounting bolt for removing CKP sensor from V8 would do it all for you. Remove the crankshaft position sensor mounting bolt and take out it from there completely in order to remove its o-ring .It is just a matter of reversing what happened during removal in terms of installation also remember to tighten the Crankshaft Position Sensor mounting bolt properly.

Genuine Chevrolet Monte Carlo Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Crankshaft Position Sensors found

View related parts
Chevrolet Monte Carlo Sensor Assembly, Cr/Shf Posn
Part Number: 12703627
$49.37 MSRP: $102.52
You Save: $53.15 (52%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 12585546
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Monte Carlo | LS, LT, SS | 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Sensor,Crankshaft Position
Part Number: 10456555
$34.05 MSRP: $70.71
You Save: $36.66 (52%)
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 10456043
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2005 Chevrolet Monte Carlo | IMPALA, LS, LS 4 DOOR, LT, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, POLICE CAR, SS, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L
View related parts
Chevrolet Monte Carlo Sensor,Crankshaft Position
Part Number: 12567648
$90.78 MSRP: $188.47
You Save: $97.69 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 24508212, 10231684, 12550965
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ 4 DOOR, LUMINA, MONTE CARLO | 6 Cyl 3.1L, 6 Cyl 3.4L
View related parts
Chevrolet Monte Carlo Sensor,Crankshaft Position
Part Number: 12560228
$65.50 MSRP: $117.48
You Save: $51.98 (45%)
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 12555566
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 Chevrolet Monte Carlo | LS, LT, SS | 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Sensor,Crankshaft Position
Part Number: 10456161
$56.78 MSRP: $164.86
You Save: $108.08 (66%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor)
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2005 Chevrolet Monte Carlo | IMPALA, LS, LT, LTZ, LUMINA, POLICE CAR, SS, Z34 | 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Sensor Assembly, Crankshaft Position <Use 12F 37
Part Number: 12598208
$23.29 MSRP: $43.94
You Save: $20.65 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor)
- Replaces: 12591007
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L
View related parts
Chevrolet Monte Carlo Sensor Assembly, Crankshaft Position
Part Number: 10226176
$41.59 MSRP: $92.90
You Save: $51.31 (56%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 24504569
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Monte Carlo | LS, LS 4 DOOR, LUMINA, MONTE CARLO | 6 Cyl 3.4L
View related parts
Chevrolet Monte Carlo Sensor,Knock
Part Number: 10456287
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Control Module, ESC Sensor, Knock Sensor, Sensor
- Replaces: 10456017
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1988 Chevrolet Monte Carlo | CLASSIC 4 DOOR, CLASSIC STATION WAGON, EL CAMINO, MONTE CARLO | 6 Cyl 3.8L, 8 Cyl 4.4L, 8 Cyl 5.0L
View related parts
Chevrolet Monte Carlo Knock, Sensor O/L
Part Number: 10456019
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Knock Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1987 Chevrolet Monte Carlo | EL CAMINO, MONTE CARLO
View related parts
Chevrolet Monte Carlo Sensor,Knock
Part Number: 10456208
$62.27 MSRP: $111.70
You Save: $49.43 (45%)
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Knock Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Monte Carlo | LS, LS 4 DOOR, LUMINA, MONTE CARLO | 6 Cyl 3.1L
View related parts
Chevrolet Monte Carlo Sensor,Crankshaft Position
Part Number: 12567649
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor)
- Replaces: 24506494, 24508213, 24506905
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Chevrolet Monte Carlo | IMPALA, LS, LT, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, POLICE CAR, SS, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L

Chevrolet Monte Carlo Crankshaft Position Sensor

The Crankshaft Position Sensor in Chevrolet Monte Carlo is an important electronic part of the car that controls phase of the engine and sends impulses to the engine control mechanism. It is an important component that determines facets like the amount of fuel injected and when it is injected, and when the ignition should take place among other parameters of the engine. It plays an important role to work efficiently with engine and it can lead to start- up problems in case of failure. The type of the sensor may be inductive, Hall Effect, magnetoresistive, or optical, where each of them has certain strengths and certain weaknesses. In summing up, Crankshaft Position Sensor plays a critical role in smooth operation of the engines of the Chevrolet Monte Carlo cars.

Each OEM Chevrolet Monte Carlo Crankshaft Position Sensor we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Monte Carlo Crankshaft Position Sensor Parts Questions & Experts Answers

Sensor,Crankshaft Position
12560228
Q: How to replace the CKP sensor for Chevrolet Impala and Monte Carlo?
A: Both V6 and V8 models have their CKP sensors placed on the back side of the engine block. When you have to drive the vehicle to a dealer, after replacing the CKP sensor and starting the engine, and let service department perform crank-shaft position variation team procedure with a factory scan tool if Malfunction Indicator Light (MIL) comes on. To replace the sensor, raise the vehicle and place it securely on jackstands. The electrical connector should be disconnected from CKP sensor. That bolt that holds CKP sensor should be removed. The old CKP sensor 0-ring should be removed and discarded thereafter. Be sure to use a new 0-ring when installing even if you are installing an old one. Just reverse what you did when removing it as far as installation is concerned. Remember to use a new 0-ring and tighten up CKP sensor mounting bolt properly. On V8 models, near flywheel is where CKP sensor is located at. Get rid of the rear exhaust manifold. Removing electrical connector while undoing the mounting bolt for removing CKP sensor from V8 would do it all for you. Remove the crankshaft position sensor mounting bolt and take out it from there completely in order to remove its o-ring .It is just a matter of reversing what happened during removal in terms of installation also remember to tighten the Crankshaft Position Sensor mounting bolt properly.