How do you replace the crankshaft pulley and front Crankshaft Seal in four cylinder engine on Chevrolet Malibu?

In order to replace the crankshaft pulley, the vehicle should be lifted and support on jack stands, and then remove the under vehicular splash shield. Next involves the removal of the drive belt and in the case of the 1.5L engine the drive belt tensioner. Tap or lock the pulley so that it stops then proceed to remove the center bolt of the crankshaft pulley. Check condition of rubber damper segment of the pulley; retain old bolt for use in the initial phase of installation if necessary. To do this use a crankshaft pulley remover or you can also use a standard crankshaft processor puller with the exhaust U-bolts then shift the crankshaft pulley off the crankshaft. If you have max out the above procedures and you needed to replace the crankshaft front oil seal then go to the next step. New pulley apply clean engine oil on the hub, align it with the oil pump rotor and the crankshaft flat and insert it. Replacing a particular bolt by a new one, secure the pulley and again tighten the bolt up to the recommended torque setting. The process of installing is the reverse of removal process and at the last reconnect the battery. For crankshaft front oil seal replace, then you have to remove the crankshaft pulley, to use a seal removal tool to take out the old seal, clean seal bore and check for any damages. Apply clean engine oil on the lip of new seal and screw it into the bore till it sits on the cylinder head timing chain cover with the fully open side directed into the engine. Before fitting the crankshaft pulley make sure that the sealing surface of the crankshaft pulley hub is greased.

Genuine Chevrolet Malibu Crankshaft Pulley

Crankshaft Pulley Engine Harmonic Balancer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Crankshaft Pulleys found

View related parts
Chevrolet Malibu Balancer Assembly, Cr/Shf
Part Number: 12697768
$57.42 MSRP: $99.97
You Save: $42.55 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 12626355, 12674685, 12603181
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2012 Chevrolet Malibu | 4 DOOR HYBRID, LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 6 Cyl 3.6L
View related parts
Chevrolet Malibu Balancer Assembly, Cr/Shf
Part Number: 25202078
$58.86 MSRP: $102.43
You Save: $43.57 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Balancer, Vibration Damper
- Replaces: 12657638, 12626962
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2022 Chevrolet Malibu | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.5L
View related parts
Chevrolet Malibu Pulley,Crankshaft
Part Number: 14023148
Product Specifications
- Other Name: PULLEY, Engine Crankshaft And Camshaft Balancer; Pulley
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1983 Chevrolet Malibu | CLASSIC 4 DOOR, CLASSIC STATION WAGON, EL CAMINO, MONTE CARLO | 6 Cyl 3.8L
View related parts
Chevrolet Malibu Pulley Assembly, (3 Groove 7.320 Pd)
Part Number: 560328
Product Specifications
- Other Name: PULLEY, Engine Crankshaft And Camshaft Balancer; Pulley
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1983 Chevrolet Malibu | CLASSIC 4 DOOR, CLASSIC STATION WAGON, EL CAMINO, MONTE CARLO | 8 Cyl 5.7L Diesel
View related parts
Chevrolet Malibu Pulley,Crankshaft
Part Number: 25522581
Product Specifications
- Other Name: PULLEY, Engine Crankshaft And Camshaft Balancer; Pulley
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1983 Chevrolet Malibu | CLASSIC 4 DOOR, CLASSIC STATION WAGON, EL CAMINO, MONTE CARLO | 6 Cyl 3.8L
View related parts
Chevrolet Malibu Pulley Assembly, Crankshaft
Part Number: 14023145
Product Specifications
- Other Name: PULLEY, Engine Crankshaft And Camshaft Balancer; Pulley
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1983 Chevrolet Malibu | CLASSIC 4 DOOR, CLASSIC STATION WAGON, EL CAMINO, MONTE CARLO | 8 Cyl 4.4L, 8 Cyl 5.0L
View related parts
Chevrolet Malibu Damper Assembly, Torsional
Part Number: 14082324
Product Specifications
- Other Name: DAMPER, Engine Crankshaft And Camshaft Balancer; Damper, Hub, Pulley, Vibration Damper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1983 Chevrolet Malibu | CLASSIC 4 DOOR, CLASSIC STATION WAGON, EL CAMINO, MONTE CARLO | 6 Cyl 3.8L
View related parts
Chevrolet Malibu Balancer Assembly, Crankshaft
Part Number: 12551948
Product Specifications
- Other Name: DAMPER; Vibration Damper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1983 Chevrolet Malibu | CLASSIC 4 DOOR, CLASSIC STATION WAGON, EL CAMINO, MONTE CARLO | 8 Cyl 4.4L, 8 Cyl 5.0L

Chevrolet Malibu Crankshaft Pulley

The Performance Crankshaft Pulley is integrated into Chevrolet Malibu car models to transmit torque from the engine to other components like the power steering pump, a/c compressor and the alternator among others. The Performance Crankshaft Pulley is attached directly to the crankshaft of the engine whereby it incorporates torque-harnessing aspects alongside counteracting engine vibrations which also affords it the secondary title of the harmonic balance wheel. In the years past, there have been several Chevrolet Malibu Performance Crankshaft Pulley models that have been used, but they are all aimed at improvement of performance and ideal efficiency. Such pulleys may be made of different materials or designed in different ways, these variations affect such factors as the weight and vibration-absorbing capacity of the pulleys.

Each OEM Chevrolet Malibu Crankshaft Pulley we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Malibu Crankshaft Pulley Parts Questions & Experts Answers

Balancer Assembly, Cr/Shf
25202078
Q: How do you replace the crankshaft pulley and front Crankshaft Seal in four cylinder engine on Chevrolet Malibu?
A: In order to replace the crankshaft pulley, the vehicle should be lifted and support on jack stands, and then remove the under vehicular splash shield. Next involves the removal of the drive belt and in the case of the 1.5L engine the drive belt tensioner. Tap or lock the pulley so that it stops then proceed to remove the center bolt of the crankshaft pulley. Check condition of rubber damper segment of the pulley; retain old bolt for use in the initial phase of installation if necessary. To do this use a crankshaft pulley remover or you can also use a standard crankshaft processor puller with the exhaust U-bolts then shift the crankshaft pulley off the crankshaft. If you have max out the above procedures and you needed to replace the crankshaft front oil seal then go to the next step. New pulley apply clean engine oil on the hub, align it with the oil pump rotor and the crankshaft flat and insert it. Replacing a particular bolt by a new one, secure the pulley and again tighten the bolt up to the recommended torque setting. The process of installing is the reverse of removal process and at the last reconnect the battery. For crankshaft front oil seal replace, then you have to remove the crankshaft pulley, to use a seal removal tool to take out the old seal, clean seal bore and check for any damages. Apply clean engine oil on the lip of new seal and screw it into the bore till it sits on the cylinder head timing chain cover with the fully open side directed into the engine. Before fitting the crankshaft pulley make sure that the sealing surface of the crankshaft pulley hub is greased.