My Garage
My Account
Cart
Genuine Chevrolet K1500 Ignition Coil
Ignition Coil Resistor- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Ignition Coils found
Chevrolet K1500 Distributor Ignition Pickup
Part Number: 10495089$26.43 MSRP: $49.86You Save: $23.43 (47%)Ships in 1-3 Business Days
Chevrolet K1500 COIL ASM,IGN
Part Number: 19418996$73.64 MSRP: $154.70You Save: $81.06 (53%)Ships in 1-3 Business Days
Chevrolet K1500 COIL KIT,IGN
Part Number: 19418995$38.60 MSRP: $109.38You Save: $70.78 (65%)Ships in 1-2 Business Days
Chevrolet K1500 Ignition Coil
The Ignition Coil in Chevrolet K1500 vehicles plays a very important role of converting 12 volts supply from the Battery to a high voltage of (15,000- 40,000 volts) required to fire the Air/Fuel mixture in the engine cylinders. This component is the link between the primary and secondary circuits of the ignition system; it is built with two coils of insulated copper wire mounted on an iron core to develop the right voltage. Since the production of K1500, there have been several ignition coils systems manufactured including single coil, distributor ignition, COP and wasted spark ignition systems. The basic difference among these types can be stated in terms of their configuration and functioning; for example, COP systems install a coil directly on each spark plug while wasted spark system uses one coil for two cylinders. Maintaining proper functioning of the ignition coil does involve general periodic servicing as well as timely replacing of the ignition coil in cases of some problems as for instance hard starts, fouling of the spark plugs, and low fuel economy among others.
Each OEM Chevrolet K1500 Ignition Coil we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Chevrolet K1500 Ignition Coil Parts Questions & Experts Answers
- Q: How to replace the Ignition Coil for Chevrolet C1500 and K1500?A: To disconnect the cable from the negative terminal of a battery, detach first if not done earlier the high tension lead of the coil and primary wire connector. Then remove mounting fasteners to separate coil from engine. For 1996 through 2000 models, take away electrical connectors from ignition coil and Ignition Control Module, and unplug coil wire from high-tension terminal. Remove ignition coil/module bracket mounting bolts and pull assembly out through engine. On a workbench, drill center of rivets holding coil to bracket, punch out rivets and remove coil off bracket. Screw new screws into bracket while retaining it with ignition coil. Finally put assembly back on engine and connect electrical connectors as well as fit in the wires into their respective terminals in the coil.
- Q: How to remove and install a distributor and pick-up coil for Chevrolet C1500 and K1500?A: Disconnect the cable from the negative battery terminal. Caution: On models equipped with the Theftlock audio system, be sure the lockout feature is turned off before performing any procedure which requires disconnecting the battery. Remove the Distributor cap and rotor. Remove the distributor from the engine. Detach the ignition coil leads from the module. Mark the distributor shaft and gear so they can be reassembled in the same relationship. Carefully mount the distributor in a vise equipped with soft jaws and, using a hammer and punch, remove the roll pin from the distributor shaft and gear. Pull out the distributor shaft. To remove the ignition coil, mount the distributor shaft in a vise equipped with soft jaws and, using a pin punch and hammer, knock out the roll pin. Remove the driven gear and spacer washers or springs from the end of the shaft-be sure to note their installed order. Remove the shaft from the distributor. To detach the ignition coil, remove the retaining clip. Lift the ignition coil assembly straight up and detach it from the distributor. Installation is the reverse of removal.
