How to remove the Shift Cable?

To remove the air inlet duct of the throttle body, all cables should be unclipped or freed from their retainers. Use a small pry-bar to push the cable off of the transaxle selector lever ball stud and then squeeze together the tabs on the cable housing to release it from where it is held near the lever by a bracket. Before finally pulling off of the shift lever, tie something such as wire or cord to its end. After you have taken out your shifter assembly, under the carpeting and out through your firewall pull it forward. Reverse steps for installation and adjust new cable after installing. For 2006 models, disconnect cable from manual lever on transaxle and place manual lever in neutral position. Inside car put shift lever in neutral and pull up on cable adjuster tab at cable bracket on transaxle then connect cable to manual lever. Cable will self adjust automatically Make sure that engine starts in only Park and Neutral positions. Park shift lever for 2007-onward vehicle models while setting parking brake. To release cable end do not grasp white part of plastic connector; instead pull back it with spring button pressed down. This will allow adjusting tensioning by means of a spring inside this mechanism for final release. Push white part of plastic connector back into its original position and check if all gear positions can be selected properly Adjust if necessary the tension setting on a transmission control cable.

Genuine Chevrolet Impala Shift Cable

Transmission Shift Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Shift Cables found

View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 25940463
$76.76 MSRP: $133.59
You Save: $56.83 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Replaces: 15952337
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2011 Chevrolet Impala | LS, LT, LTZ, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15873759
$68.94 MSRP: $119.98
You Save: $51.04 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chevrolet Impala | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.8L, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 20836465
$33.96 MSRP: $50.78
You Save: $16.82 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable; Shift Control Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2016 Chevrolet Impala | LS, LTZ | 6 Cyl 3.6L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 22856120
$26.86 MSRP: $40.16
You Save: $13.30 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever; Shift Control Cable
- Replaces: 20836463
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2016 Chevrolet Impala | LS, LTZ | 6 Cyl 3.6L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 84145766
$40.66 MSRP: $63.95
You Save: $23.29 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable Assembly, A/Trns Range Sel Lvr; Shift Control Cable
- Replaces: 22955157, 22758167, 23274920, 23226826
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Impala | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15873761
$75.06 MSRP: $112.22
You Save: $37.16 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Replaced by: 19434393
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chevrolet Impala | IMPALA, LS, LT | 6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.8L, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 22758166
$12.02 MSRP: $17.96
You Save: $5.94 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever; Shift Control Cable
- Replaces: 22955156
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2015 Chevrolet Impala | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 84145765
$47.96 MSRP: $71.70
You Save: $23.74 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever; Shift Control Cable
- Replaces: 23226825, 23274919
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 25940464
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable; Shift Control Cable
- Replaces: 25807291
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2011 Chevrolet Impala | LS, LT, LTZ | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 25940466
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable; Shift Control Cable
- Replaces: 25859097
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2011 Chevrolet Impala | LS, LT, LTZ, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Automatic Transmission Shifter Cable Assembly
Part Number: 26046375
Product Specifications
- Other Name: Cable Asm,Steering Column Brake Trns Shift Interlock ; Cable, Transmission Shift Brake Interlock; Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Impala | LUMINA | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15873762
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Replaces: 15283253
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Chevrolet Impala | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.8L, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Impala Automatic Transmission Range Select Lever Kit
Part Number: 12458106
Product Specifications
- Other Name: Cable Kit,Automatic Transmission Range Selector Lever
- Replaces: 12454861, 12453165, 12533143, 12534783
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Impala | LUMINA | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Automatic Transmission Parking Lock Cable Assembly
Part Number: 15283247
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Parking Lock ; Cable, Transmission Shift Control Cable
- Replaces: 15142773, 12563605, 12569408
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Automatic Transmission Range Select Lever Kit
Part Number: 19152619
Product Specifications
- Other Name: Cable Kit,Automatic Transmission Range Selector Lever; Shift Control Cable
- Replaces: 88996495
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 Chevrolet Impala | LS, LT | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Impala Automatic Transmission Range Select Lever Kit
Part Number: 19152621
Product Specifications
- Other Name: Cable Kit,Automatic Transmission Range Selector Lever; Shift Control Cable
- Replaces: 88996494
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 Chevrolet Impala | LS, LT, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Impala Automatic Transmission Range Select Lever Kit
Part Number: 12458109
Product Specifications
- Other Name: Cable Kit,Automatic Transmission Range Selector Lever; Shift Control Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Impala | IMPALA, LS, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Automatic Transmission Range Select Lever Kit
Part Number: 12458110
Product Specifications
- Other Name: Cable Kit,Automatic Transmission Range Selector Lever; Shift Control Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Impala | IMPALA, LS, SS | 6 Cyl 3.4L, 6 Cyl 3.8L

Chevrolet Impala Shift Cable

Each OEM Chevrolet Impala Shift Cable we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Impala Shift Cable Parts Questions & Experts Answers

Automatic Transmission Range Selector Lever Cable Assembly
25940463
Q: How to remove the Shift Cable?
A: To remove the air inlet duct of the throttle body, all cables should be unclipped or freed from their retainers. Use a small pry-bar to push the cable off of the transaxle selector lever ball stud and then squeeze together the tabs on the cable housing to release it from where it is held near the lever by a bracket. Before finally pulling off of the shift lever, tie something such as wire or cord to its end. After you have taken out your shifter assembly, under the carpeting and out through your firewall pull it forward. Reverse steps for installation and adjust new cable after installing. For 2006 models, disconnect cable from manual lever on transaxle and place manual lever in neutral position. Inside car put shift lever in neutral and pull up on cable adjuster tab at cable bracket on transaxle then connect cable to manual lever. Cable will self adjust automatically Make sure that engine starts in only Park and Neutral positions. Park shift lever for 2007-onward vehicle models while setting parking brake. To release cable end do not grasp white part of plastic connector; instead pull back it with spring button pressed down. This will allow adjusting tensioning by means of a spring inside this mechanism for final release. Push white part of plastic connector back into its original position and check if all gear positions can be selected properly Adjust if necessary the tension setting on a transmission control cable.