How do you remove the brake master cylinder on Chevrolet Impala?

Start by depressing the brake pedal multiple times to deplete the vacuum reserve in order to remove the brake master cylinder. You can find the Brake Master Cylinder in the engine compartment and it is mounted to the power brake booster. Ensure that you do not use it for food preparation again by removing excess fluid from the reservoir using a syringe or turkey baster. Prepare caps or plastic bags to cover line ends, and put rags beneath fluid fittings. Pulling slightly away from the Brake Master Cylinder, loosen flare-nut wrench fittings at ends of brake lines and plug the ends. The electrical connector for the brake fluid level sensor should be disconnected first, then nuts attaching it to the power booster removed. Be careful when handling it so as not to spill any fluid while removing the Brake Master Cylinder. If installing a new Brake Master Cylinder, tap out retaining pins transferring old reservoir and install new seals. Attach bleeder tubes to outlet ports after mounting it in a vise then bench bleed it before installing new one on your vehicle. Recommended brake fluid should be used on this process as you will need to fill up its reservoir accordingly while slowly pushing pistons into Brake Master Cylinder with your fingers to let air out then repeat until no more bubbles are seen. Remove plugs from open ports and take off bleeding tubes when finished. Thread by hand, tighten mounting nuts finger tight onto power brake booster and make sure that you fully tighten mounting nuts as well as brake line fittings respectively with hand screwing threaded into Brake Master Cylinders. Connect electrical connector of brake fluid level sensor now on go ahead filling fluids into Brake Master Cylinders' reservoirs before bleeding them together with entire braking system altogether, Before you use your vehicle test its braking system extensively.

Genuine Chevrolet Impala Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Brake Master Cylinders found

View related parts
Chevrolet Impala Cylinder Kit, Brake Master
Part Number: 23176885
$119.29 MSRP: $236.68
You Save: $117.39 (50%)
ADD TO CART
Product Specifications
- Other Name: CYLINDER KIT, Brake Master Cylinder; Master Cylinder
- Replaced by: 84626898
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
Chevrolet Impala Cylinder Assembly, Brake Master
Part Number: 22796285
$147.94 MSRP: $293.54
You Save: $145.60 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 25908489, 20885005, 20967783
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2016 Chevrolet Impala | LS, LT, LT 3.5, LTZ, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.6L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 18029965
$111.66 MSRP: $265.88
You Save: $154.22 (58%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Impala | LUMINA | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 19176108
$183.90 MSRP: $346.99
You Save: $163.09 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Impala | CLASSIC 4 DOOR, CLASSIC STATION WAGON | 8 Cyl 5.7L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 19176498
$91.00 MSRP: $163.22
You Save: $72.22 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder
- Replaces: 18030402, 25509416
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1983 Chevrolet Impala | 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON, STATION WAGON | 6 Cyl 3.8L, 8 Cyl 4.4L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 5.7L Diesel
View related parts
Chevrolet Impala Repair Kit, Brake Mast Cyl
Part Number: 18007935
Product Specifications
- Other Name: CYLINDER KIT, Brake Master Cylinder; Master Cylinder Repair Kit, Overhaul Kit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Chevrolet Impala | 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON, STATION WAGON | 6 Cyl 3.8L, 8 Cyl 4.4L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 5.7L Diesel
View related parts
Chevrolet Impala Cylinder,Brake Master
Part Number: 18013426
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Chevrolet Impala | 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON, STATION WAGON | 6 Cyl 3.8L, 6 Cyl 4.3L, 8 Cyl 4.4L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 5.7L Diesel
View related parts
Chevrolet Impala Repair Kit, Brake Master Cylinder
Part Number: 18016508
Product Specifications
- Other Name: CYLINDER KIT, Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | CLASSIC 4 DOOR, CLASSIC STATION WAGON, LS 4 DOOR | 8 Cyl 5.7L
View related parts
Chevrolet Impala Cylinder Assembly, Brake Master
Part Number: 15925739
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 10337908
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Impala | LS, LS POLICE CAR, LT, LT 3.5, LTZ, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 18060781
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003 Chevrolet Impala | IMPALA | 6 Cyl 3.8L
- 2000-2001 Chevrolet Impala | IMPALA | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 19209185
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 10382902
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Impala | LS, LS POLICE CAR, LT, LT 3.5, LTZ, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 19209186
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder
- Replaces: 10382903
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Impala | LS, LS POLICE CAR, LT, LT 3.5, LTZ, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 19209247
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 18047667
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Chevrolet Impala | IMPALA, LS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 19209260
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 18060780, 18026277
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | IMPALA, LS, LT, LUMINA, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 19209261
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 18060783
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Cylinder,Brake Master
Part Number: 18029971
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 18021808
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | CLASSIC 4 DOOR, CLASSIC STATION WAGON, LS 4 DOOR | 8 Cyl 5.7L
View related parts
Chevrolet Impala Cylinder Asm,Brake Master
Part Number: 18029966
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 18021270
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Impala | CLASSIC 4 DOOR, CLASSIC STATION WAGON | 8 Cyl 5.7L

Chevrolet Impala Brake Master Cylinder

Brake Master Cylinder in Chevrolet Impala cars is an essential braking system unit of turning the force exerted by the foot into hydraulic pressure to compel slave cylinders. This system uses hydraulic fluid to transmits force from the master cylinder's piston to the slave cylinders; force and displacement are increased. Chevrolet Impala cars usually incorporate a dual circuit master cylinder with 2 pistons Operated whereby even if hydraulic pressure in either of the two circuits is lost, the continued pressure is enough for the car to stop. Master cylinder works operational calipers or drum brakes in order to generate some friction into the wheel in an endeavor to halt it and at the same times works for slave cylinder regarding clutch deactivation. In general, the Brake Master Cylinder in Chevrolet Impala automobiles plays a critical role of preventing the mishandling of hydraulic force and pressure which is very vital for the proper functioning of the brake and the clutch of the automobile.

Each OEM Chevrolet Impala Brake Master Cylinder we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Impala Brake Master Cylinder Parts Questions & Experts Answers

Cylinder Assembly, Brake Master
22796285
Q: How do you remove the brake master cylinder on Chevrolet Impala?
A: Start by depressing the brake pedal multiple times to deplete the vacuum reserve in order to remove the brake master cylinder. You can find the Brake Master Cylinder in the engine compartment and it is mounted to the power Brake Booster. Ensure that you do not use it for food preparation again by removing excess fluid from the reservoir using a syringe or turkey baster. Prepare caps or plastic bags to cover line ends, and put rags beneath fluid fittings. Pulling slightly away from the Brake Master Cylinder, loosen flare-nut wrench fittings at ends of Brake Lines and plug the ends. The electrical connector for the brake fluid level sensor should be disconnected first, then nuts attaching it to the power booster removed. Be careful when handling it so as not to spill any fluid while removing the Brake Master Cylinder. If installing a new Brake Master Cylinder, tap out retaining pins transferring old reservoir and install new seals. Attach bleeder tubes to outlet ports after mounting it in a vise then bench bleed it before installing new one on your vehicle. Recommended brake fluid should be used on this process as you will need to fill up its reservoir accordingly while slowly pushing pistons into Brake Master Cylinder with your fingers to let air out then repeat until no more bubbles are seen. Remove plugs from open ports and take off bleeding tubes when finished. Thread by hand, tighten mounting nuts finger tight onto power brake booster and make sure that you fully tighten mounting nuts as well as brake line fittings respectively with hand screwing threaded into Brake Master Cylinders. Connect electrical connector of brake fluid level sensor now on go ahead filling fluids into Brake Master Cylinders' reservoirs before bleeding them together with entire braking system altogether, Before you use your vehicle test its braking system extensively.