How to remove and install an ignition coil on Chevrolet Corvette?

Disconnect the cable from the negative battery terminal. Removing the engine cover(s). The ignition coils could be removed as a complete assembly from each cylinder bank or taken out independently from mounting bracket. When removing the entire assembly, unplug the main electrical connector of igntion coil. Disconnect spark plug wires from spark plugs. Take off ignition coil bracket mounting bolts and remove it with assembly from valve cover. If removing an individual coil, detach spark plug wire from it. Take off ignition coil mount bolts and remove coil away out of its seat on bracket. Pull apart ignition coil electrical connector. Put everything back in position to how it was before disconnection. Unfasten the ignition coil electrical connector. Separate sparking plug cords and let them not stay longer on sparking plugs themselves.Discharge screws for fixing and extricate valve jacket by pulling bracket upwards.Remove locked bolts then shift blocked away.Remove electrical connection to igniting device.Inverse action must be performed after detachment.Disconnect electric coupling to inflammator.Sequester rope ends which are into holes of fire-producing pieces.Decompose downbolts at last.Getting rid of circuit breaker.Reassemble everything that has been detached.Liberate cord entanglement with electrifier.Inextricably intertwine a leash end in hot point's place.Move button upwards against spring pressure.Press fuel accelerator pedal firmly.Pushing flame handle downwards.To start up water supply turn tap handle left.Turn key towards bottommost.Put petroleum lamp regulation control at any point.Prepare switch for either starting or emission mark.Fire-off switch should be turned right.Put control gear lever in neutral position.Run through limber-up phase.Gradually release brake.Having started braking, one should stop pushing pedals.Once you have pushed both buttons replace claw-type bolt.Rollback loop.For gun-fire discharge make two clicks.Then relax brake.Drag drive shaft carefully away.Open your throttle wide.Pull rudder bar backwards till contact becomes impossible.Release hand wheel slowly.Make water to bubble ifand when necessary.Latch gear wheel on corresponding index pin.Disconnect the throttle rod.

Genuine Chevrolet Corvette Ignition Coil

Ignition Coil Resistor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Ignition Coils found

View related parts
Chevrolet Corvette Ignition Coil Assembly
Part Number: 12699382
$72.20 MSRP: $151.66
You Save: $79.46 (53%)
ADD TO CART
Product Specifications
- Other Name: Coil Assembly, Ign; Coil, Ignition Coil
- Replaces: 12573190
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2013 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE | 8 Cyl 6.0L, 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette Ignition Coil Assembly
Part Number: 10477208
$55.07 MSRP: $103.91
You Save: $48.84 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil Asm,Ignition ; Coil, Ignition Coil; Ignition Coil
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Ignition Coil
Part Number: 12611424
$72.20 MSRP: $151.66
You Save: $79.46 (53%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil,Ignition; Coil
- Replaced by: 12699382
- Replaces: 12570616
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2013 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE | 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette Coil Assembly, Ign
Part Number: 12708496
$75.36 MSRP: $158.33
You Save: $82.97 (53%)
ADD TO CART
Product Specifications
- Other Name: Ignition Coil
- Replaced by: 12726023
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE, Z06 2 DOOR CONVERTIBLE, Z06 2 DOOR PLAINBACK | 8 Cyl 6.2L
View related parts
Chevrolet Corvette COIL ASM,IGN
Part Number: 19418996
$73.64 MSRP: $154.70
You Save: $81.06 (53%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ignition Coil
- Replaces: 10489421, 19207138
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette COIL ASM,IGN
Part Number: 19421259
$46.68 MSRP: $132.35
You Save: $85.67 (65%)
ADD TO CART
Product Specifications
- Other Name: Ignition Coil
- Replaces: 12556450, 12558948
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet Corvette | 2 DOOR, CONVERTIBLE, NOTCHBACK | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Ignition Coil Kit
Part Number: 12498336
$68.96 MSRP: $144.86
You Save: $75.90 (53%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Coil Kit,Ignition ; Coil, Ignition Coil; Coil, Ignition Coil
- Replaces: 01985474, 1985474
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1991 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Ignition Coil
Part Number: 10467067
$52.29 MSRP: $98.66
You Save: $46.37 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil,Ignition
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1995 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette COIL ASM-IGN
Part Number: 12728713
$46.63 MSRP: $83.64
You Save: $37.01 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Ignition Coil
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | LT6 CONVERTIBLE, LT6 COUPE | 8 Cyl 5.5L
View related parts
Chevrolet Corvette Coil Assembly, Ign
Part Number: 12713668
$29.08 MSRP: $52.16
You Save: $23.08 (45%)
Product Specifications
- Other Name: Ignition Coil
- Replaced by: 12723610
- Replaces: 12619161, 12669351
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2024 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE, LT2 AWD CONVERTIBLE, LT2 AWD COUPE, Stingray Convertible, STINGRAY CONVERTIBLE, Stingray Coupe, STINGRAY COUPE, Z06 2 DOOR CONVERTIBLE, Z06 2 DOOR PLAINBACK | 8 Cyl 6.2L

Chevrolet Corvette Ignition Coil

The Ignition Coil is used in Chevrolet Corvette cars specifically for ignition where low voltage coming from the alternator is stepped up to provide ignition of fuel in the cylinders. It plays a crucial role of producing sparks and need to be effective for the proper combustion to occur in the engine. This gets rid of the common problem on current generation Corvette's programmable ignition system to get the optimal performance. Incorporated in any Corvette, no matter old or new, are the ignition coils; as for new Corvette models, the coils for each cylinder are separate. Defective ignition coils cause misfiring which has a negative impact on the performance of the car, show their significance in the performance of the car.

Each OEM Chevrolet Corvette Ignition Coil we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Corvette Ignition Coil Parts Questions & Experts Answers

COIL ASM,IGN
19421259
Q: How to remove and install an ignition coil on Chevrolet Corvette?
A: Disconnect the cable from the negative battery terminal. Removing the engine cover(s). The ignition coils could be removed as a complete assembly from each cylinder bank or taken out independently from mounting bracket. When removing the entire assembly, unplug the main electrical connector of igntion coil. Disconnect spark plug wires from spark plugs. Take off ignition coil bracket mounting bolts and remove it with assembly from valve cover. If removing an individual coil, detach spark plug wire from it. Take off ignition coil mount bolts and remove coil away out of its seat on bracket. Pull apart ignition coil electrical connector. Put everything back in position to how it was before disconnection. Unfasten the ignition coil electrical connector. Separate sparking plug cords and let them not stay longer on sparking plugs themselves.Discharge screws for fixing and extricate valve jacket by pulling bracket upwards.Remove locked bolts then shift blocked away.Remove electrical connection to igniting device.Inverse action must be performed after detachment.Disconnect electric coupling to inflammator.Sequester rope ends which are into holes of fire-producing pieces.Decompose downbolts at last.Getting rid of circuit breaker.Reassemble everything that has been detached.Liberate cord entanglement with electrifier.Inextricably intertwine a leash end in hot point's place.Move button upwards against spring pressure.Press fuel accelerator pedal firmly.Pushing flame handle downwards.To start up water supply turn tap handle left.Turn key towards bottommost.Put petroleum lamp regulation control at any point.Prepare switch for either starting or emission mark.Fire-off switch should be turned right.Put control gear lever in neutral position.Run through limber-up phase.Gradually release brake.Having started braking, one should stop pushing pedals.Once you have pushed both buttons replace claw-type bolt.Rollback loop.For gun-fire discharge make two clicks.Then relax brake.Drag drive shaft carefully away.Open your throttle wide.Pull rudder bar backwards till contact becomes impossible.Release hand wheel slowly.Make water to bubble ifand when necessary.Latch gear wheel on corresponding index pin.Disconnect the throttle rod.