How do you remove the Fuel Level Sensor,Fuel Pump and Fuel Pump Driver Module?

To remove the fuel pump module, first relieve the fuel system pressure and disconnect the negative battery terminal. For 2002 and earlier models or early-build 2003 models without RPO FFS, loosen the lug nuts on the left or right-rear wheel, raise the vehicle, and remove the corresponding wheel. Drain the fuel tank and clean the fittings and fuel pump module area. Remove the fuel tank shield, disconnect the electrical connector and fuel supply line quick-connect fittings from the fuel pump module, and remove the fuel tank strap. Support the fuel tank and remove the fuel pump module bolts to take out the module from the tank. For the left tank, transfer the float arm to the new fuel pump module and align the gasket tab with the mark on the module. Tighten the bolts in a criss-cross pattern and complete the installation in reverse order. Add fuel to the tank, reconnect the battery, and check for fuel leaks. If the fuel pump module needs to be serviced, remove the fuel tank and disconnect any electrical connectors, jet line insert connector, fuel feed line, and additional fuel or EVAP lines connected to the module. Use a fuel sender lock ring tool or pliers to remove the module lock ring and carefully pull the fuel pump module out of the tank. Disconnect the jet line quick-connect fittings and remove the module from the tank. For models with LS9 engines, remove the fuel return line from the base of the module. If replacing the right fuel pump module, transfer the fuel tank pressure sensor to the new module. To replace the fuel level sensor, disconnect the wires at the module connector and press in on the tab to slide the sensor upward. Install a new fuel pump module O-ring and install the module. Verify that the fuel level sensor is not catching on anything inside the tank and complete the installation in reverse order. Add fuel to the tank, reconnect the battery, and check for fuel leaks. For the fuel pump driver module (FPDM) and relay, remove the carpet and access cover, disconnect the electrical connector from the FPDM or relay, release the mounting tabs, and remove the FPDM. The FPDM relay is secured with adhesive tape, so peel it up from the floor panel. Installation is the reverse of removal, and the FPDM must be programmed after replacement using a scan tool.

Genuine Chevrolet Corvette Fuel Pump

Gas Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Fuel Pumps found

View related parts
Chevrolet Corvette MODULE KIT,F/TNK F/PMP (W/O FUEL LVL SEN)
Part Number: 19420858
$337.16 MSRP: $708.32
You Save: $371.16 (53%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fuel Pump, Sending Unit
- Replaces: 19149689, 19149228, 19133432, 19417894, 19418613, 19302042, 19354664
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2013 Chevrolet Corvette | 2 DOOR, CONVERTIBLE, NOTCHBACK | 8 Cyl 5.7L, 8 Cyl 6.0L, 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette Pump Assembly, Fuel
Part Number: 12711662
$252.26 MSRP: $529.97
You Save: $277.71 (53%)
ADD TO CART
Product Specifications
- Other Name: Fuel Pump
- Replaced by: 12728002
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Pump Assembly, Fuel
Part Number: 12711668
$929.57 MSRP: $1952.85
You Save: $1023.28 (53%)
ADD TO CART
Product Specifications
- Other Name: Fuel Pump
- Replaces: 12679090, 12673410, 12642287, 12694529, 12688607
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2019 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE, Z06 2 DOOR CONVERTIBLE, Z06 2 DOOR PLAINBACK | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Pump Assembly, Fuel
Part Number: 12692704
$210.83 MSRP: $397.81
You Save: $186.98 (47%)
ADD TO CART
Product Specifications
- Other Name: Fuel Pump
- Replaced by: 12735881
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Corvette | LT2 AWD CONVERTIBLE, LT2 AWD COUPE, Stingray Convertible, STINGRAY CONVERTIBLE, Stingray Coupe, STINGRAY COUPE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette MODULE KIT,F/TNK F/PMP
Part Number: 19420818
$1567.27 MSRP: $2836.68
You Save: $1269.41 (45%)
ADD TO CART
Product Specifications
- Other Name: Fuel Pump, Sending Unit
- Replaces: 19207431
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | 2 DOOR SPECIAL | 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette MODULE KIT,F/TNK F/PMP
Part Number: 19420859
$395.36 MSRP: $830.58
You Save: $435.22 (53%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fuel Pump
- Replaces: 10337590, 19133430, 19417895, 19301842, 19149227, 19418614, 19354666
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 Chevrolet Corvette | 2 DOOR, CONVERTIBLE, NOTCHBACK | 8 Cyl 5.7L, 8 Cyl 6.0L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette PUMP ASM-FUEL
Part Number: 12735880
$102.98 MSRP: $184.72
You Save: $81.74 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | LT2 AWD CONVERTIBLE, LT2 AWD COUPE, Stingray Convertible, STINGRAY CONVERTIBLE, Stingray Coupe, STINGRAY COUPE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette PUMP ASM-FUEL
Part Number: 12711467
$178.35 MSRP: $321.36
You Save: $143.01 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fuel Pump
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | LT6 CONVERTIBLE, LT6 COUPE | 8 Cyl 5.5L
View related parts
Chevrolet Corvette PUMP ASM-FUEL
Part Number: 12711486
$178.35 MSRP: $321.36
You Save: $143.01 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fuel Pump
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | LT6 CONVERTIBLE, LT6 COUPE | 8 Cyl 5.5L
View related parts
Chevrolet Corvette Fuel Pump Assembly
Part Number: 25163463
Product Specifications
- Other Name: Pump Asm,Fuel ; Pump, Fuel Pump; Fuel Pump
- Replaces: 25117502, 25116053, 25117453, 25116168
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Fuel Pump
Part Number: 25168719
Product Specifications
- Other Name: Pump,Fuel
- Replaces: 25166252, 6472232, 25166717, 6472011
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Fuel Pump Assembly
Part Number: 25163464
Product Specifications
- Other Name: Pump Asm,Fuel ; Pump, Fuel Pump; Fuel Pump
- Replaces: 25117454
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Fuel Sender Assembly
Part Number: 19179534
Product Specifications
- Other Name: Sender Asm,Fuel ; Sender, Fuel Tank Meter/Pump; Fuel Gauge Sending Unit, Fuel Pump, Gauge
- Replaces: 25027510
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1996 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Fuel Sender Assembly
Part Number: 19180770
Product Specifications
- Other Name: Sender Asm,Fuel; Fuel Gauge Sending Unit, Fuel Pump, Gauge
- Replaces: 25094243, 25028725
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1995 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Fuel Tank Fuel Pump Module Kit (Acdelco)
Part Number: 19354816
Product Specifications
- Other Name: Module Kit,Fuel Tank Fuel Pump (Acdelco)
- Replaced by: 19420820
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE | 8 Cyl 6.0L, 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette Fuel Tank Fuel Pump Module Kit (W/O Fuel Level Sensor)
Part Number: 19354819
$214.15 MSRP: $385.86
You Save: $171.71 (45%)
Product Specifications
- Other Name: Module Kit,Fuel Tank Fuel Pump (W/O Fuel Level Sensor); Sending Unit
- Replaces: 19257053
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | 2 DOOR SPECIAL | 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette MODULE KIT,F/TNK F/PMP
Part Number: 19421166
$337.41 MSRP: $607.94
You Save: $270.53 (45%)
Product Specifications
- Other Name: Fuel Pump
- Replaces: 88895126, 12459860, 19354302, 89047748
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Chevrolet Corvette | 2 DOOR, CONVERTIBLE, NOTCHBACK | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Fuel Tank Fuel Pump Module Kit (W/O Fuel Level Sensor)
Part Number: 19354814
$409.20 MSRP: $737.30
You Save: $328.10 (45%)
Product Specifications
- Other Name: Module Kit,Fuel Tank Fuel Pump (W/O Fuel Level Sensor); Fuel Pump, Sending Unit
- Replaces: 19257051
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE | 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette Fuel Tank Fuel Pump Module Kit
Part Number: 19354300
Product Specifications
- Other Name: Module Kit,Fuel Tank Fuel Pump; Fuel Pump
- Replaces: 89047746, 12458242, 88896043
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Corvette | 2 DOOR, CONVERTIBLE, NOTCHBACK | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Fuel Tank Meter/Pump SENDER
Part Number: 25003533
Product Specifications
- Other Name: Sender,Fuel ; Sender, Fuel Tank Meter/Pump; Fuel Gauge Sending Unit, Gauge
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L

Chevrolet Corvette Fuel Pump

The Fuel Pump of Chevrolet Corvette vehicles is in charge of pumping fuel in the vehicle's engine for better combustion. Usually, in the modern Corvette, an electrical immersed pump installed in the fuel tank is used for this purpose. In the case of a faulty fuel pump, problems with torque and power output of the car can develop and this can definitely become risky. The various signs that may point towards a faulty fuel pump includes: Slow operations; acceleration of poor quality; and starting problems. In its turn, it is suggested to consult with the fuel filter and, if the problems still exist, to analyze the fuel pressure for its proper operating.

Each OEM Chevrolet Corvette Fuel Pump we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Corvette Fuel Pump Parts Questions & Experts Answers

MODULE KIT,F/TNK F/PMP (W/O FUEL LVL SEN)
19420858
Q: How do you remove the Fuel Level Sensor,Fuel Pump and Fuel Pump Driver Module?
A: To remove the fuel pump module, first relieve the fuel system pressure and disconnect the negative battery terminal. For 2002 and earlier models or early-build 2003 models without RPO FFS, loosen the lug nuts on the left or right-rear wheel, raise the vehicle, and remove the corresponding wheel. Drain the Fuel Tank and clean the fittings and fuel pump module area. Remove the fuel tank shield, disconnect the electrical connector and fuel supply line quick-connect fittings from the fuel pump module, and remove the fuel tank strap. Support the fuel tank and remove the fuel pump module bolts to take out the module from the tank. For the left tank, transfer the float arm to the new fuel pump module and align the gasket tab with the mark on the module. Tighten the bolts in a criss-cross pattern and complete the installation in reverse order. Add fuel to the tank, reconnect the battery, and check for fuel leaks. If the fuel pump module needs to be serviced, remove the fuel tank and disconnect any electrical connectors, jet line insert connector, fuel feed line, and additional fuel or EVAP lines connected to the module. Use a fuel sender lock ring tool or pliers to remove the module lock ring and carefully pull the fuel pump module out of the tank. Disconnect the jet line quick-connect fittings and remove the module from the tank. For models with LS9 engines, remove the fuel return line from the base of the module. If replacing the right fuel pump module, transfer the fuel tank pressure sensor to the new module. To replace the fuel level sensor, disconnect the wires at the module connector and press in on the tab to slide the sensor upward. Install a new fuel pump module O-ring and install the module. Verify that the fuel level sensor is not catching on anything inside the tank and complete the installation in reverse order. Add fuel to the tank, reconnect the battery, and check for fuel leaks. For the fuel pump driver module (FPDM) and relay, remove the carpet and access cover, disconnect the electrical connector from the FPDM or relay, release the mounting tabs, and remove the FPDM. The FPDM relay is secured with adhesive tape, so peel it up from the floor panel. Installation is the reverse of removal, and the FPDM must be programmed after replacement using a scan tool.