How do you remove the ignition switch and Ignition Lock Cylinder?

To remove the ignition lock cylinder, start by disconnecting the negative battery cable and removing the steering column covers. Then, remove the Park lock switch and slide off the theft deterrent control module if applicable. Next, place the key in the lock and rotate it clockwise to the Accessory position. Push in the retainer pin and pull out the key and ignition lock cylinder from the housing. To replace the ignition lock/switch housing, remove the multi-function switch/airbag coil and its mounting plate from the column. Remove the shear bolt from the ignition switch housing by drilling a hole in the center and using a screw extractor. If you only need to remove the electrical portion of the ignition switch, disconnect the electrical connector and remove the switch. To install the ignition lock cylinder, align the retainer with the slot in the housing and push it in until it snaps into position. When installing the new shear bolt, tighten it until the shear head breaks off. Finally, reverse the steps for reinstallation.

Genuine Chevrolet Colorado Ignition Lock Cylinder

Ignition Key Lock Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Ignition Lock Cylinders found

View related parts
Chevrolet Colorado Cylinder Kit,Ignition Lock (Uncoded)
Part Number: 20766607
$30.01 MSRP: $56.62
You Save: $26.61 (47%)
ADD TO CART
Product Specifications
- Other Name: CYLINDER KIT, Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2018 Chevrolet Colorado | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB LS - 6'2" BOX, CREW CAB LT - 6'2" BOX, EXTENDED CAB - 6'2" BOX, LS CREW CAB - 5'2" BOX, LS EXTENDED CAB - 6'2" BOX, LT CREW CAB - 5'2" BOX, LT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.5L, 4 Cyl 2.8L Diesel, 6 Cyl 3.6L
View related parts
Chevrolet Colorado Ign Start Switch
Part Number: 89022365
$29.92 MSRP: $49.53
You Save: $19.61 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Ignition Switch; Cylinder & Keys, Ignition Lock Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 Chevrolet Colorado | CREW CAB, EXTENDED CAB, EXTENDED LENGTH, PICKUP | 4 Cyl 2.8L, 4 Cyl 2.9L, 5 Cyl 3.5L, 5 Cyl 3.7L, 8 Cyl 5.3L
View related parts
Chevrolet Colorado Cylinder Assembly, Ign Lk
Part Number: 13528553
$73.37 MSRP: $109.66
You Save: $36.29 (34%)
Product Specifications
- Replaces: 13526234
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2021 Chevrolet Colorado | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB LS - 6'2" BOX, CREW CAB LT - 6'2" BOX, EXTENDED CAB - 6'2" BOX, LS CREW CAB - 5'2" BOX, LS EXTENDED CAB - 6'2" BOX, LT CREW CAB - 5'2" BOX, LT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.5L, 4 Cyl 2.8L Diesel, 6 Cyl 3.6L

Chevrolet Colorado vehicles Possess an Ignition Lock Cylinder that enables the drivers to switch on their Cars through a slot near the steering wheel after placing and turning the key. This cylinder is part of the ignition switch and is uniquely made to have some keys and tumbler holes to make it secured. Gradually, new technologies have enhanced the principle of the keyless start system, but ignition lock cylinders are still used in many vehicles and are quite secure. Despite their rather sturdy construction, these cylinders may wear out after some time and bring about problems that may include a challenge in rotating the key or occupying the car's engine. To these concerns, there are replacement switches, lock cylinders and other related parts to help gain timely normalcy and safety together with the functionality of the car.

Chevrolet Colorado Ignition Lock Cylinder Parts Questions & Experts Answers

Ign Start Switch
89022365
Q: How do you remove the ignition switch and Ignition Lock Cylinder?
A: To remove the ignition lock cylinder, start by disconnecting the negative battery cable and removing the steering column covers. Then, remove the Park lock switch and slide off the theft deterrent control module if applicable. Next, place the key in the lock and rotate it clockwise to the Accessory position. Push in the retainer pin and pull out the key and ignition lock cylinder from the housing. To replace the ignition lock/switch housing, remove the multi-function switch/airbag coil and its mounting plate from the column. Remove the shear bolt from the ignition switch housing by drilling a hole in the center and using a screw extractor. If you only need to remove the electrical portion of the ignition switch, disconnect the electrical connector and remove the switch. To install the ignition lock cylinder, align the retainer with the slot in the housing and push it in until it snaps into position. When installing the new shear bolt, tighten it until the shear head breaks off. Finally, reverse the steps for reinstallation.