What is the location and function of the brake light switch for Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

The brake light switch is located on the brake pedal bracket and can be accessed by removing the trim panel beneath the steering column. If there is no voltage, use a test light to locate any short or open between the battery and the switch. If there is voltage at the switch, check if there is voltage on the ground side of the switch when the brake pedal is depressed. If there is no voltage, look for a short or open in the ground circuit and repair it. To replace the switch, remove the trim panel below the steering column, unplug the electrical connector, remove the retainer from the brake pedal pin, and unsnap the switch from the brake pedal pushrod. Installation is the reverse of removal. To adjust the switch, depress the brake pedal, insert the switch into its bracket, and push it in until it is fully seated. Slowly pull the brake pedal to the rear until there are no clicking sounds, indicating that the switch is adjusted. This can be verified with an ohmmeter or continuity tester by checking that the switch contacts are open at one inch or less of brake pedal travel, and closed thereafter.

Genuine Chevrolet Blazer Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Brake Light Switches found

View related parts
Chevrolet Blazer Switch Assembly, Stop Lamp & Cruise
Part Number: 25524845
$15.13 MSRP: $31.78
You Save: $16.65 (53%)
ADD TO CART
Product Specifications
- Other Name: SWITCH, Stop Lamp Switch; Brake Switch, Stoplamp Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1991 Chevrolet Blazer | 1/2 TON | 6 Cyl 2.8L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L Diesel
View related parts
Chevrolet Blazer Sensor Assembly, Brake Pedal Position
Part Number: 13597425
$12.78 MSRP: $24.11
You Save: $11.33 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Brake; Pedal Travel Sensor, Stoplamp Switch
- Replaces: 13583372
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2024 Chevrolet Blazer | HIGH COUNTRY/LTZ 4 DOOR SUV, L 4 DOOR SUV, LT 4 DOOR SUV, RS 4 DOOR SUV | 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
Chevrolet Blazer Sensor Assembly, Brake Pedal Position
Part Number: 13597424
$29.87 MSRP: $56.38
You Save: $26.51 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Brake; Pedal Travel Sensor, Sensor, Stoplamp Switch
- Replaces: 13583371
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Blazer | HIGH COUNTRY/LTZ 4 DOOR SUV, LT 4 DOOR SUV, RS 4 DOOR SUV | 4 Cyl 2.0L
View related parts
Chevrolet Blazer Switch,Stop Lamp
Part Number: 15961519
$20.60 MSRP: $38.86
You Save: $18.26 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SWITCH, Stop Lamp Switch; Stoplamp Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Chevrolet Blazer | 1/2 TON | 6 Cyl 4.3L, 8 Cyl 5.7L
View related parts
Chevrolet Blazer Switch,Stop Lamp
Part Number: 93801734
$12.86 MSRP: $20.50
You Save: $7.64 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SWITCH, Stop Lamp Switch; Stoplamp Switch
- Replaces: 12450076, 15732489
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Chevrolet Blazer | 1/2 TON | 6 Cyl 4.3L, 8 Cyl 5.7L, 8 Cyl 6.5L Diesel
View related parts
Chevrolet Blazer Switch,Stop Lamp
Part Number: 15128745
$13.06 MSRP: $24.64
You Save: $11.58 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SWITCH, Stop Lamp Switch; Stoplamp Switch, Switch
- Replaces: 15741137, 15981543
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2005 Chevrolet Blazer | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
Chevrolet Blazer Switch,Stop Lamp
Part Number: 15962182
Product Specifications
- Other Name: SWITCH, Stop Lamp Switch; Stoplamp Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1991 Chevrolet Blazer | 1/2 TON | 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L Diesel

Chevrolet Blazer Brake Light Switch

The Brake Light Switch is also installed in Chevrolet Blazer cars whereby it is responsible for turning on the brake light when the brake pedal of the car is pressed. This mechanism makes drivers behind the Blazer know when the vehicle is slowing down or stopping thus increasing road safety. Although the overview does not characterize different types or styles of Brake Light Switch used in different models of Blazer, the reader has to understand that their primary function remains more or less the same. The Brake Light Switch plays a very critical role in signaling and it gives an indication to other road users about braking actions.

Each OEM Chevrolet Blazer Brake Light Switch we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Blazer Brake Light Switch Parts Questions & Experts Answers

Switch,Stop Lamp
15128745
Q: What is the location and function of the brake light switch for Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: The brake light switch is located on the brake pedal bracket and can be accessed by removing the trim panel beneath the steering column. If there is no voltage, use a test light to locate any short or open between the battery and the switch. If there is voltage at the switch, check if there is voltage on the ground side of the switch when the brake pedal is depressed. If there is no voltage, look for a short or open in the ground circuit and repair it. To replace the switch, remove the trim panel below the steering column, unplug the electrical connector, remove the retainer from the brake pedal pin, and unsnap the switch from the brake pedal pushrod. Installation is the reverse of removal. To adjust the switch, depress the brake pedal, insert the switch into its bracket, and push it in until it is fully seated. Slowly pull the brake pedal to the rear until there are no clicking sounds, indicating that the switch is adjusted. This can be verified with an ohmmeter or continuity tester by checking that the switch contacts are open at one inch or less of brake pedal travel, and closed thereafter.