My Garage
My Account
Cart
Genuine Cadillac Eldorado Fuel Tank
Gas Tank- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Fuel Tanks found
Cadillac Eldorado Fuel Tank
The Fuel Tank of Cadillac Eldorado vehicles delivers liquid fuel and its vapors to engines as a storage chamber. Usually mounted at the rear, the structure of the tank always includes fuel filler pipe, vent and connections to engines. The Cadillac Eldorado fuel tanks come as both metallic as well as the plastic type where the metallic type comes in steel or aluminum stamped and welded from sheets while the plastic type is molded High Density Polyethylene (HDPE). There have been changes in the construction of the fuel tanks over time while where the fabricated tanks should fit, efforts are made on quality of the tanks to be replaced. In metal tanks, they are usually likely to develop corrosion and rust while in the case of plastic tanks, they are likely to crack under unfavourable conditions. Fuel tank is essential component of the Cadillac Eldorado transmission and is plays significant role in the safety and reliability of the fuel delivery system.
Each OEM Cadillac Eldorado Fuel Tank we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Cadillac Eldorado Fuel Tank Parts Questions & Experts Answers
- Q: How do you remove and install the fuel tank on Cadillac ElDorado?A: To remove the fuel tank from early model Fleetwood, Deville, Eldorado, and Seville vehicles, start by disconnecting the negative battery cable and relieving the fuel system pressure, followed by draining the fuel tank. Remove the fuel filler door assembly and disconnect the screw retaining the filler pipe-to-body bracket, then raise the vehicle and support it with jackstands. Detach the tank level sender lead connector and support the tank with a transmission jack or equivalent before removing the two tank retaining straps. Lower the tank enough to disconnect the ground lead and fuel hoses from the pump assembly, then carefully remove the tank to ensure all connections and hoses are disconnected. For installation, use a new Fuel Pump O-ring gasket to install the pump/sender assembly into the tank, ensuring the strainer does not block the float arm's full travel. Place the tank on the jack, position the sound insulators, and raise the tank to attach the electrical and hose connectors. Raise the tank to the proper position and loosely install the retaining straps, tightening them to 26 ft. lbs. (35 Nm) once the tank is correctly positioned. Connect the grounding strap and negative battery cable, then turn the ignition key to the ON position with the engine OFF to check for fuel leaks at the tank. For later models, disconnect the negative battery cable and relieve the fuel system pressure before raising the vehicle and supporting it with jackstands. Drain the fuel tank and detach the fuel feed and return quick-connect fittings by twisting the connections to loosen dirt, blowing out any debris if compressed air is available, and squeezing the plastic tabs to pull the connections apart. Detach the fuel sender electrical connector, then, with assistance, support the tank and remove the fuel tank strap retaining nuts and bolts, placing the tank in a suitable work area. For installation, position and support the tank with assistance, install the fuel tank straps and retaining nuts and bolts, tightening them to 26 ft. lbs. (34 Nm). Install the vapor pipe, attach the fuel sender electrical connector, and reconnect the fuel feed and return quick-connect fittings, applying a few drops of clean engine oil to the male connector pipe ends to ensure proper reconnection and prevent leaks. Push the connectors together until the retaining tabs snap into place, then pull on both ends of each connection to ensure they are secure. Lower the vehicle, turn the ignition switch to the ON position for 2 seconds, then to OFF for 5 seconds, and again turn to ON to check for leaks.
