How do you replace the TP sensor on Cadillac DeVille and DTS?

For the later models, TP sensor is a component of the throttle body and has to be replaced as a whole. Start by detaching the cable from the negative battery terminal. The IAC valve is positioned above the TP sensor and so it is prudent to unplug its electrical connector and set aside. Even though there are some hoses and pipes in front of the TP sensor, you can carefully remove mounting screws for TP sensor without removing any of them. Then, unplug the electrical connector from the TP sensor. For Throttle Body Removal: Unplug the electrical connector first, then take out the screws which mount that particular sensor. Once again, remove two screws used to mount the TP Sensor before pulling it off completely. If equipped with an old TPS O-ring, discard it before reinstalling a new O-ring to avoid any air leaks; note that even if you install your old TPS, use a fresh O-ring because air leakage might result when you reuse it. This reassembly takes place in reverse.

Genuine Cadillac Deville Throttle Position Sensor

TPS Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Throttle Position Sensors found

View related parts
Cadillac Deville Sensor,Throttle Position
Part Number: 17123852
$39.09 MSRP: $79.62
You Save: $40.53 (51%)
ADD TO CART
Product Specifications
- Other Name: SENSOR, Multi Port Fuel Injection Throttle Position; Actuator, Throttle Position Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1999 Cadillac Deville | 4 DOOR, DEVILLE, SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Deville Sensor Asm,Throttle Position
Part Number: 88893282
$101.67 MSRP: $184.86
You Save: $83.19 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Multi Port Fuel Injection Throttle Position; Throttle Position Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Cadillac Deville | DEVILLE, FUNERAL COACH, HIGH LUXURY, LIMOUSINE, SEVILLE, SLS, STS, TOURING 4 DOOR, TOURING SEDAN | 8 Cyl 4.6L
View related parts
Cadillac Deville Sensor,Throttle Position
Part Number: 17106684
Product Specifications
- Other Name: SENSOR KIT, Multi Port Fuel Injection Throttle Position; Throttle Position Sensor
- Replaces: 17112609
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1995 Cadillac Deville | 2 DOOR, 4 DOOR, 60 SPECIAL 4 DOOR, CONVERSION, TOURING 4 DOOR | 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Deville Sensor Asm,Tb Throttle Position
Part Number: 17106682
$68.75 MSRP: $123.33
You Save: $54.58 (45%)
Product Specifications
- Other Name: SENSOR KIT, Multi Port Fuel Injection Throttle Position; Throttle Position Sensor
- Replaces: 17112677, 17087654
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Cadillac Deville | 4 DOOR | 8 Cyl 4.6L

Cadillac Deville Throttle Position Sensor Parts Questions & Experts Answers

Sensor Asm,Throttle Position
88893282
Q: How do you replace the TP sensor on Cadillac DeVille and DTS?
A: For the later models, TP sensor is a component of the throttle body and has to be replaced as a whole. Start by detaching the cable from the negative battery terminal. The IAC valve is positioned above the TP sensor and so it is prudent to unplug its electrical connector and set aside. Even though there are some hoses and pipes in front of the TP sensor, you can carefully remove mounting screws for TP sensor without removing any of them. Then, unplug the electrical connector from the TP sensor. For Throttle Body Removal: Unplug the electrical connector first, then take out the screws which mount that particular sensor. Once again, remove two screws used to mount the TP Sensor before pulling it off completely. If equipped with an old TPS O-ring, discard it before reinstalling a new O-ring to avoid any air leaks; note that even if you install your old TPS, use a fresh O-ring because air leakage might result when you reuse it. This reassembly takes place in reverse.