Warranty: This genuine part is guaranteed by GM's
factory warranty.
Fits the following Vehicles:
2018-2020 Buick Regal | 1SC 4 DOOR HATCHBACK, 1SL 4 DOOR HATCHBACK, 1SX 4 DOOR HATCHBACK, BASE 4 DOOR HATCHBACK, BASE 4 DOOR STATION WAGON | 4 Cyl 2.0L, 6 Cyl 3.6L
Warranty: This genuine part is guaranteed by GM's
factory warranty.
Fits the following Vehicles:
2018 Buick Regal | 1SC 4 DOOR HATCHBACK, 1SL 4 DOOR HATCHBACK, 1SL 4 DOOR STATION WAGON, 1SX 4 DOOR HATCHBACK, BASE 4 DOOR HATCHBACK, BASE 4 DOOR STATION WAGON | 4 Cyl 2.0L, 6 Cyl 3.6L
Warranty: This genuine part is guaranteed by GM's
factory warranty.
Fits the following Vehicles:
2018-2020 Buick Regal | 1SC 4 DOOR HATCHBACK, 1SL 4 DOOR HATCHBACK, 1SL 4 DOOR STATION WAGON, 1SX 4 DOOR HATCHBACK, BASE 4 DOOR HATCHBACK, BASE 4 DOOR STATION WAGON | 4 Cyl 2.0L, 6 Cyl 3.6L
Warranty: This genuine part is guaranteed by GM's
factory warranty.
Fits the following Vehicles:
2018-2020 Buick Regal | 1SC 4 DOOR HATCHBACK, 1SL 4 DOOR HATCHBACK, 1SL 4 DOOR STATION WAGON, 1SX 4 DOOR HATCHBACK, BASE 4 DOOR HATCHBACK, BASE 4 DOOR STATION WAGON | 4 Cyl 2.0L, 6 Cyl 3.6L
Warranty: This genuine part is guaranteed by GM's
factory warranty.
Fits the following Vehicles:
2018-2020 Buick Regal | 1SC 4 DOOR HATCHBACK, 1SL 4 DOOR HATCHBACK, 1SL 4 DOOR STATION WAGON, 1SX 4 DOOR HATCHBACK, BASE 4 DOOR HATCHBACK, BASE 4 DOOR STATION WAGON | 4 Cyl 2.0L, 6 Cyl 3.6L
Other Name: Latch Assembly, Rear S/D; Latch, Lock, Lock Actuator
Position: Rear
Replaced by: 13546554
Warranty: This genuine part is guaranteed by GM's
factory warranty.
Fits the following Vehicles:
2019-2020 Buick Regal | 1SC 4 DOOR HATCHBACK, 1SL 4 DOOR HATCHBACK, 1SL 4 DOOR STATION WAGON, 1SX 4 DOOR HATCHBACK, BASE 4 DOOR HATCHBACK, BASE 4 DOOR STATION WAGON | 4 Cyl 2.0L, 6 Cyl 3.6L
Q: How to remove and install a Buick Century and Regal door lock?
A: Make sure the window is up all the way. Then, remove both the upper and lower portions of the trim pad. Going in through the largest access hole, disengage the rod connecting the remote control to the lock as follows: Use a suitable prytool to slide the spring clip out of engagement. The clip must be slid on the lock lever until the ends of the clip no longer engage with the grooved section of the end of the lock rod. You don't need to remove the clip from the lock lever. There is a slot in the rear side of the clip so it can shift on the lock lever even though the lockrod passes right through it. Pull the lockrod out of the lock lever. If the car has electric locks, remove the solenoid. Remove the three screws mounting the lock onto the door lock pillar section of the door and remove the lock. On some models, it may be necessary to remove the inside remote handle and then remove the lock and the connecting rod together. On four door models, it will be necessary to remove the lock, then separate the lockrod from the lock on a work-bench, and install the rod onto the new lock. Install in exact reverse order. Tighten the lock mounting screws to 7-12 ft. lbs. (9-16 Nm).