My Garage
My Account
Cart
Genuine Buick Enclave Axle Shaft
Car Axle Shaft- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
14 Axle Shafts found
Buick Enclave Cv Intermediate Shaft
Part Number: 20899365$104.96 MSRP: $264.12You Save: $159.16 (61%)
Buick Enclave Front Driver Side Half, Shaft Assembly
Part Number: 23231834$279.68 MSRP: $486.76You Save: $207.08 (43%)Ships in 1-2 Business Days
Buick Enclave Front Wheel Drive Shaft Assembly (Rh Proc)
Part Number: 25849949$289.99 MSRP: $504.72You Save: $214.73 (43%)Ships in 1-2 Business Days
Buick Enclave Shaft Assembly, Front Whl Drv Half
Part Number: 84609405$122.83 MSRP: $309.09You Save: $186.26 (61%)Ships in 1-2 Business Days
Buick Enclave Rear Wheel Drive Shaft Assembly
Part Number: 84088441$125.83 MSRP: $208.26You Save: $82.43 (40%)Ships in 1-2 Business Days
Buick Enclave Shaft Assembly, Front Whl Drv Half
Part Number: 84750308$261.40 MSRP: $454.94You Save: $193.54 (43%)Ships in 1-2 Business DaysBuick Enclave Shaft Assembly, Rear Whl Drv
Part Number: 84853345$122.81 MSRP: $194.06You Save: $71.25 (37%)Ships in 1-3 Business Days
Buick Enclave Shaft Assembly, Front Whl Drv
Part Number: 84686587$267.68 MSRP: $423.07You Save: $155.39 (37%)Ships in 1-2 Business DaysBuick Enclave Shaft Assembly, Rear Whl Drv
Part Number: 84598346$134.50 MSRP: $212.58You Save: $78.08 (37%)Ships in 1-3 Business Days
Buick Enclave Rear Wheel Drive Shaft Assembly
Part Number: 23219922$158.32 MSRP: $250.20You Save: $91.88 (37%)Ships in 1-3 Business Days
Buick Enclave Front Driver Side Half, Shaft Assembly
Part Number: 84445329$223.15 MSRP: $388.39You Save: $165.24 (43%)Ships in 1-3 Business Days
Buick Enclave Rear Wheel Drive Shaft Assembly
Part Number: 23219923$137.33 MSRP: $217.04You Save: $79.71 (37%)
Buick Enclave Axle Shaft
The Axle Shaft of Buick Enclave automobiles is a critical item that directs power from the differential to the drive wheels and also helps in independent rotation facilities that improve adhesion. These steel shafts are of different types including solid axles for trucks and old model cars and half shafts for cars that have independent suspension system. Distinct axles accommodate the differential as well as the axle shafts and half-shafts which transmits the power from the transaxle to the wheels. Due to rubbing on obstacles, the axle shafts undergo wear and tear, which can cause concerns such as noise and vibration Experienced seals wear and tear affects the proper functioning of the axle as it leads to loss of lubrication and contamination of the brakes. In summary, The Axle-Shaft provides support to the weight of the Buick enclave vehicle, transmits torque and provides proper angle to the wheels.
Each OEM Buick Enclave Axle Shaft we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Buick Enclave Axle Shaft Parts Questions & Experts Answers
- Q: How do you remove driveaxle?A: To remove the front axle shaft, start by removing the wheel center cover and breaking the axle shaft/hub nut loose using a large breaker bar. Loosen the wheel lug nuts, raise the vehicle, and support it on jackstands. Remove the wheel and, if necessary, the front inner fender splash shields. Disconnect the tie-rod end and stabilizer bar link from the steering knuckle. Remove the axle shaft/hub nut and discard it. Separate the control arm ball joint from the steering knuckle and swing the knuckle/hub assembly away from the vehicle to free the axle shaft. If removing the right axle shaft, pry the inner CV Joint off the intermediate shaft, and for the left axle shaft, pry the inner CV joint out of the transaxle. Carefully remove the axle shaft from the vehicle, supporting the CV joints. When installing the new axle shaft, replace the spring clip at the inner end and lubricate the differential or intermediate shaft seal with grease. Raise the axle shaft into position while supporting the CV joints and push the splined end of the inner CV joint into the differential side gear or onto the intermediate shaft. Ensure the spring clip locks in its groove and that the axle shaft retaining ring is securely seated in the transaxle or intermediate shaft. Install the washer on the outer CV end of the axle shaft. Apply grease to the outer CV joint splines and insert the stub axle into the hub. Reconnect the balljoint stud into the steering knuckle, tighten the bolt to specifications, and reinstall the tie-rod end and stabilizer-bar link. Install the front inner fender splash shields if removed, and install a new axle shaft hub nut. Lower the vehicle, tighten the lug nuts and axle shaft/hub nut to specifications, and install the wheel center cover. For the intermediate shaft removal, first remove the right front axle shaft, then take out the bolts mounting the intermediate shaft bearing retainer to the engine bracket. Pull the intermediate shaft from the transaxle. During installation, lubricate the lips of the transaxle seal with grease, carefully guide the intermediate shaft into the transaxle side gear, and install the mounting bolts hand-tight for the bearing support. Ensure the shaft is positively engaged into the transaxle, then tighten the nuts to specifications. Install a new spring clip on the right front axle shaft, and complete the rest of the installation in reverse. For rear (AWD) removal, start by removing the wheel center cover and breaking the Axle Shaft/hub nut loose with a large breaker bar. Block the front wheels, loosen the rear wheel lug nuts, raise the vehicle, and support it on jackstands. Remove the wheel, discard the Axle Shaft/hub nut, and use a brass punch or block of wood with a hammer to break the Axle Shaft loose from the wheel hub. Remove the hub and bearing assembly. If removing the right rear Axle Shaft, remove the muffler assembly. Pry the Axle Shaft out of the differential and remove it through the knuckle opening, removing and replacing the retaining ring with a new one. When installing the new Axle Shaft, install a new retaining ring on the inner end, apply a light film of grease to the inner CV joint stub shaft, guide the Axle Shaft through the knuckle opening, and insert the splined end of the inner CV joint into the differential, ensuring the spring clip locks in its groove. Install the hub and bearing assembly, a new Axle Shaft/hub nut, and the wheel center cover. Lower the vehicle, tighten the lug nuts and Axle Shaft/hub nut to specifications, and ensure the Axle Shaft is properly installed.
