Make sure this part fits

Pontiac 91177686 Pump Kit, Oil (On Esn)

1996-1997 Pontiac Sunrunner

Customer Questions & Expert Answers (3)
GM 91177686 Pump Kit, Oil (On Esn)
  • Part Description
    PUMP, Engine Oil Pump
  • Replaces
    91176682, 91177558, 91177447, 91177121, 91172378
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Pontiac
    Manufacturer Part Number91177686
    Part DescriptionPUMP, Engine Oil Pump
    Other NamesOil Pump
    Item Dimensions12.7 x 5.8 x 5.7 inches
    Item Weight2.70 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces91176682, 91177558, 91177447, 91177121, 91172378
    ManufacturerGeneral Motors
    SKU91177686
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1996-1997 Pontiac Sunrunner4 Cyl 1.6L2 DOOR HARD TOP, CONVERTIBLE
  • Customer Questions & Expert Answers

    Q:
    I am wonder if this is complete and correct part for my vehicle. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 91177686 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to remove and inspect an oil pump in DOHC engine? Posted by Customer
    A:
    The oil pan is the first item to be removed, and then comes the oil pump pickup tube. Then, it is followed by removing of the oil pump sprocket cover bolts and detaching the sprocket cover. The chain guide nuts of the oil pump drive are loosened and pushed away from the chain a little bit to create some slack in it. Lastly, remove all of the mounting bolts holding down your pump before taking off its entire body or any other piece that might damage or hinder proper functioning. This will damage the center shaft in your oil pump if you try to separate it from your sprocket ring. For inspection purposes, this unit is taken apart whereupon every part gets cleaned thoroughly before being inspected for wear and tear cracks other damages. All parts should be replaced as necessary after being checked visually for wear, cracks, and other obvious signs of damage. This is followed by putting in place outer rotors of oil pumps whose clearance will later be measured between their peripheries and cases as well as from one rotor face to another using straightedges respectively. The free length of this spring must be measured on a flat metal surface such as a workbench or table before replacement if too short for purpose since relief valve spring has to be replaced when shortest possible than 1 inch for pressure regulation purposes on such pumps while still installed within system at time under them according some technical specifications typically used by various manufacturers such those contained herein. Lastly, petroleum jelly will fill up cavity while rotor faces go back into their spaces along with installation of rotors followed closely by fixing together two halves making housing complete when relief valve retainer also inserted which forms part comprising first figure shown below represents assembly line view for quick reference only-do not use these images unless explicitly stated otherwise.). Examination of excessive wear or damage should now take place using eyesight alone applied directly onto chains rollers attached between driver teeth plates; damaged unit could thus be replaced without needing to look further than that. Depending on the condition of the chain, it may need changing if worn or damaged in any way before removal from crankshaft becomes possible; this process alone requires removing crankshaft because it is now known as a unit with this inside and out. By carefully placing oil pump on block along accompanied by simple placement without tension, ensure that there's a provision for pump drive chain being supplied or installed while mounting completed above same block: through front side coincide onto its studs where lastly tightened. This is done by having an assistant pull the scale until the reading on it reached between 4.4 and 6.6 pounds of pressure when he pushes back so that your chain tightens itself up again with no more pulling required from his side whatsoever after which these nuts should be screwed down tightly against base posts holding shift lever housing's whole assembly right outwards just enough thereby allowing them touch each other always-never go too far apart!). You will then need to put back nut lock washer over bolt head leaving loose just like before then follow all other steps below secures lid securely tightening every screw onto pump housing back together after understanding what goes where, going ahead repair damages sealants or adhesive materials etc.; finally adding any remaining liquids into engine start run motor checking if there are no problems connected either directly related only those previously mentioned during discussion question about Leaks.).
    Posted by GMPartsGiant Specialist
    Q:
    What should be done after removing the parts for the 1997 Chevrolet Tracker? Posted by Customer
    A:
    Thoroughly clean all parts and remove any old gasket material from the sealing surfaces. Visually inspect all parts for wear, cracks, and damage. Replace any parts that are worn or damaged.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Oil Pump
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 91177686, the Right Choice

To ensure reliability, purchase GM part # 91177686 Pump Kit, Oil (On Esn). It is sometimes referred to as Pontiac Oil Pump, Pontiac Oil Pump Rotor Set. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Pontiac Sunrunner models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 91177686 Pump Kit, Oil (On Esn). You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Pontiac parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly