Make sure this part fits

GMC 16128251 Electric Spark Control Module Assembly

1985-1995 GMC

Customer Questions & Expert Answers (6)
GM 16128251 Electric Spark Control Module Assembly
  • Part Description
    Module Assembly, Electronic Spark Control ; Module, Distributor (Also Knock Sensor)
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine GMC
    Manufacturer Part Number16128251
    Part DescriptionModule Assembly, Electronic Spark Control ; Module, Distributor (Also Knock Sensor)
    Other NamesESC Control Module, ESC Module, Module
    Item Dimensions6.3 x 3.3 x 3.1 inches
    Item Weight0.70 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU16128251
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1988-1995, 1985 GMC C15006 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L DieselC1500 EXTENDED CAB LONG BOX, C1500 EXTENDED CAB STANDARD BOX, C1500 REGULAR CAB LONG BOX, C1500 REGULAR CAB STANDARD BOX, REGULAR CAB LONG BOX, REGULAR CAB STANDARD BOX
    1988-1995, 1985 GMC C25006 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L DieselC2500 EXTENDED CAB LONG BOX, C2500 EXTENDED CAB STANDARD BOX, C2500 REGULAR CAB, CREW CAB, REGULAR CAB
    1993-1995, 1988-1991, 1985 GMC C35008 Cyl 5.7L, 8 Cyl 6.2L Diesel, 8 Cyl 7.4LC3500 CAB CHASSIS 135.5, C3500 CAB CHASSIS 159.9, C3500 CAB CHASSIS 183.5, C3500 CREW CAB LONG WHEELBASE, C3500 EXTENDED CAB, C3500 REGULAR CAB, CAB CHASSIS 135.5, CAB CHASSIS 159.9, CREW CAB, REGULAR CAB
    1987-1992, 1985 GMC G15006 Cyl 4.3L1/2 TON CARGO, 1/2 TON PASSENGER
    1987-1992, 1985 GMC G25006 Cyl 4.3L3/4 TON CARGO, 3/4 TON PASSENGER
    1987-1992, 1985 GMC G35006 Cyl 4.3L1 TON CARGO, 1 TON COMMERCIAL/RECREATIONAL VEHICLE, 1 TON PASSENGER
    1992, 1987-1988, 1985 GMC Jimmy6 Cyl 4.3L1/2 TON, 2 DOOR, 4 DOOR
    1988-1995, 1985 GMC K15006 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L DieselK1500 EXTENDED CAB LONG BOX, K1500 EXTENDED CAB STANDARD BOX, K1500 REGULAR CAB LONG BOX, K1500 REGULAR CAB STANDARD BOX, REGULAR CAB LONG BOX, REGULAR CAB STANDARD BOX
    1988-1995, 1985 GMC K25006 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L DieselK2500 EXTENDED CAB LONG BOX, K2500 EXTENDED CAB STANDARD BOX, K2500 REGULAR CAB, REGULAR CAB
    1993-1995, 1988-1991, 1985 GMC K35008 Cyl 5.7L, 8 Cyl 6.2L Diesel, 8 Cyl 7.4LCAB CHASSIS 135.5, CAB CHASSIS 159.9, CREW CAB, K3500 CAB CHASSIS 135.5, K3500 CAB CHASSIS 159.9, K3500 CREW CAB LONG WHEELBASE, K3500 EXTENDED CAB, K3500 REGULAR CAB, REGULAR CAB
    View More
  • Customer Questions & Expert Answers

    Q:
    I am wonder if this is complete and correct part for my vehicle. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 16128251 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to check and replace the knock sensor and Ignition Control Module for Chevrolet C1500 and K1500? Posted by Customer
    A:
    The knock sensor is liable for sensing irregular engine vibrations and minimizing spark knock. This results in a greater degree of AC output voltage, which is then given to ECM/PCM to retard the timing. Depending on the year and engine application, the location of this sensor can be different but normally it is found at the rear of the engine block or even at the side of cylinder head. For checking resistance of this sensor, remove electric connector and measure resistance between terminal and vital part of engine's body. If it falls outside this range, it should therefore be replaced. While running engine again, connect back connector and use voltmeter to verify an AC voltage signal here. Voltage ought to rise with increase in speed of an engine. If there is no any voltage signal available then knock sensor must be replaced because it has failed completely. When replacing this knock sensor just disconnect negative battery terminal before removing distributor or oil pressure sending unit if necessary; disconnect electrical connector and remove knocker from your engine block; installation is opposite to removal process. On 1988 -1995 models, ESC module located near throttle body however starting 1996 up to 2000 model years incorporated Knock Sensor Module with PCM as stated above; therefore remove PCM along with Knock Sensor Module cover also take out Knock Sensor by pinching retaining tabs & pulling up vertically straight; align tabs on notches press down until retaining clips snap into place for installing Knock Sensor Module while finally install PCM cover as well as Knock Sensor Module cover too.
    Posted by GMPartsGiant Specialist
    Q:
    What voltage reading are you looking for at the module's positive terminal, and what does it indicate for the 1997 Chevrolet Astro? Posted by Customer
    A:
    Check for voltage at the module's positive terminal with the ignition switch turned On. If it reads less than ten volts, there might be a fault in the wire between the module's positive terminal and the ignition coil's positive connector or the ignition coil's primary circuit to the ignition switch.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Ignition Control Module
    Q:
    How can the module be tested if there are suspicions of malfunction for the 1994 Chevrolet C1500? Posted by Customer
    A:
    The module can be tested with special equipment.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Ignition Control Module
    Q:
    What precautions should be taken when replacing a knock sensor, and what are the general steps for its replacement for the 1999 Chevrolet C1500? Posted by Customer
    A:
    When replacing the knock sensor, disconnect the negative battery terminal and remove the distributor or oil pressure sending unit if necessary. Disconnect the electrical connector and remove the knock sensor from the engine block. Installation is the reverse of removal.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Ignition Control Module
    Q:
    Is it necessary to remove the distributor from the engine for the 1999 Chevrolet K1500? Posted by Customer
    A:
    No, it is not necessary to remove the distributor from the engine for 1988 through 1995 models.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Ignition Control Module
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 16128251, the Right Choice

Your vehicle deserves only genuine OEM GM parts and accessories. To ensure reliability, purchase GM part # 16128251 Electric Spark Control Module Assembly. It is sometimes referred to as GMC Igniter, GMC Ignition Control Module. Our GM parts and accessories are expedited directly from authorized GM dealers strategically located all across the U.S. and are backed by the manufacturer's 12 month, 12,000 mile warranty. OEM GM parts are the best for restoring your vehicle to factory condition performance. This part fits specific GMC C2500, Suburban, Yukon models.

Affordable, reliable and built to last, GM part # 16128251 Electric Spark Control Module Assembly stands out as the smart option. GMPartsGiant.com is your prime online source with the biggest and best selection of genuine GM parts and accessories at giant discounted prices. We have the OEM GM parts and accessories you need at the wholesale prices. GMPartsGiant.com has you covered no matter what type of GM vehicle you drive. For detailed GMC parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly