GM 12605565 Filter Assembly, Oil (Cap W/Filter & Seal)

You can Select Your Vehicle to check if 12605565 fits your vehicle.

On these vehicles, there is an oil life indicator system that lights on the instrument panel as a signal to change the oil depending on factors that are used to determine that the oil is 'used up.' The vehicle manufacturer normally recommend more than 3000 miles before an oil change though frequent change of the oil is advised for a longer life of the engine. In case of choosing to trust the oil life indicator, do not go beyond 10, 000 miles without changing the oil. Because of this, it is recommended that the oil be changed frequently to avoid excess engine wear which results from contaminated oil. To start with, ensure that you have assemble all equipment that will be required and have rags in case of wiping down accidents. Lifting of the vehicle as illustrated gives easy access to the oil drain plug and filter. Find the oil drain plug and filter with care having in mind that the exhaust will be hot. The engine should first be warmed in order to ease circulation of the oil, the vehicle should then be parked at a level ground with the oil filler cap removed. Chock the wheels, place a drain pan under the drain plug and then remove the plug by using the right tools while exercising a lot of care since the plug might be hot. Afterwards, let the oil drain and while doing so one should check it for the presence of metal particles, the plug and the region around the plug should be cleaned before finally replacing the plug accurately. Place the drain pan beneath the oil filter, unscrew the cap of the filter and free the housing of any debris. Coat a new O-ring seal and the filter element then lock the cap; After removing tools and materials, lower it, and pour in four quarts of new oil through the filler cap, and check the dip stick. Switch on the engine and look for areas where there is usual leakage tighten such point so that they do not leak again. Check the oil level again and put some more if there is a need for that. To do this, turn the ignition switch on but do not start the vehicle, then press the reset button that is in the underhood fuse/relay block and get to resetting the Change Engine Oil light. First few trips after the oil change, ensure to check for leaks and the level of the oil. Ensure that the used oil is properly disposed after cooling it by having it ready to be transferred to a recycling plant rather than employing wrong trends in discarding it.

Vehicles equipped with an oil life indicator system illuminate a light or message on the instrument panel to signal the need for an oil change, typically allowing for extended intervals compared to the traditional 3000-mile mark, but it's recommended not to exceed 10,000 miles between changes. Frequent oil changes are crucial for preventive maintenance as aging engine oil becomes diluted and contaminated, contributing to premature engine wear. Before initiating the oil change, ensure you have the necessary tools and ample rags or newspapers for oil spills. Access to the oil drain plug and filter is improved when the vehicle is raised on a hoist, driven onto ramps, or supported by jackstands. Start the engine and let it reach normal operating temperature, facilitating easier oil drainage. Park on a level surface, shut off the engine, and remove the oil filler cap. Raise the vehicle, supporting it securely with jackstands. Carefully position a drain pan beneath the engine's drain plug, remove the plug with a proper-sized wrench, and be cautious of hot exhaust components. After draining, inspect the old oil for metal particles, clean the drain plug, and the surrounding area, then reinstall and tighten it. Move the drain pan under the oil filter, unscrew the filter cap, and remove both the cap and element. Clean the housing and cap thoroughly. Install a new O-ring seal and a new filter element into the cap, then insert them into the filter housing, securely tightening the cap. Lower the vehicle, add fresh oil through the filler cap using a funnel, and check the oil level with the dipstick. Start the engine for a minute, inspect for oil leaks, and recheck the dipstick. During initial trips after the oil change, monitor for leaks and proper oil levels. Properly dispose of the old oil by checking with local facilities or recycling centers. Lastly, reset the "Change Engine Oil" light using either of the two specified methods, depending on your vehicle's features, ensuring the Oil Life Monitor is successfully reset.

Start the engine and let it reach normal operating temperature, facilitating easier oil drainage. Park on a level surface, shut off the engine, and remove the oil filler cap.

Regular oil changes and maintenance are essential for engine longevity and performance because they help keep the engine lubricated with clean oil, prevent premature wear, and ensure the engine operates at its best. This contributes to overall vehicle reliability and efficiency.

Access can be improved by raising the vehicle on a hoist, driving it onto ramps, or supporting it with jackstands.

Position the drain pan under the oil filter, loosen and remove the old filter, and empty its contents into the drain pan. Compare the old and new filters to ensure they match, clean the mounting area, and apply a light coat of oil to the new filter's gasket before installation.

Reset the Change Engine Oil light by pressing the reset button in the underhood fuse/relay block.

The oil life indicator system activates a light or message on the instrument panel when it's time to change the oil, considering various factors to determine oil wear.

Position the drain pan under the oil filter, remove the old filter, clean the mounting surface, install a new O-ring seal and filter, ensuring proper seating without over-tightening.

For V6 models, the oil filter should be removed and replaced using an oil filter wrench. For four-cylinder models, the canister-type oil filter can be accessed from the top of the engine.