Chevrolet 12247409 Fuel Tank Pressure Sensor Assembly

You can Select Your Vehicle to check if 12247409 fits your vehicle.

To replace the fuel pressure sensor, start by relieving the system fuel pressure. Then, raise the vehicle and support it securely on jackstands. Disconnect the electrical connector from the fuel pressure sensor and unscrew it from the fuel supply line. Remove the old fuel pressure sensor O-ring and replace it with a new one coated in clean engine oil. Securely tighten the fuel pressure sensor. Before lowering the vehicle, test for leaks by turning the ignition switch key to the ON position for two seconds, then to the OFF position for ten seconds, and finally back to the ON position. Inspect the area around the fuel pressure sensor for leaks. To remove the fuel pump driver module, locate it under the vehicle mounted to the outside of the driver's side frame rail. Raise the front of the vehicle and support it securely on jackstands. Disconnect the electrical connector from the fuel pump driver module and remove the module from its mounting bracket by removing the nut. To install the fuel pump driver module, simply reverse the removal process.

The Evaporative Emissions Control (EVAP) system is a system designed to prevent the escape of fuel system vapors containing unburned hydrocarbons into the atmosphere. On hot days, fuel vapors that are trapped in the fuel tank continue to expand until they reach a certain pressure limit. The liquid fuels expelled from this tank move through the evaporative valve and canister, where they temporarily collect before being burnt up in an operating engine. There are times when the Powertrain Control Module (PCM) opens up the canister purge solenoid when suitable conditions are met like; warmed up engine, vehicle is at speed or there's a moderate to heavy load on the engine. This allows fuel vapour in the canister to be drawn into the intake manifold chamber for mixing with air/fuel mixture before it gets used in the combustion chambers. Both component and layout of EVAP system are critical including EVAP canister located above fuel tank consisting of activated carbon to hold vapours, fuel tank pressure sensor atop of fuel pump/fuel level sensor module and EVAP canister vent solenoid behind left rear wheel well fender liner which normally is opened but seals off for inspection/maintenance on EVAP system. It should be noted that with its duty cycle dependent on factors like vacuum in intake manifolds and data from sensors, vapor flow from canister to intake manifold is regulated by EVAP canister purge solenoid under PCM control. With all these advantages it must be remembered that troubleshooting an EVAP system requires specialized tools and training because these problems cannot be detected by ordinary people using normal senses, although some symptoms may be indicative of related problems. These include smelling gasoline on warm days primarily caused by loose or broken EVAP hose connections among other things. One method consists of removing the gas cap and listening for pressure release as signs of too much vaporized petrol within tanks, while professionals need full diagnostic test. The replacement of the EVAP canister purge solenoid on V6 engines requires removal of electrical connections, lines, and a mounting bolt for installation or reinstallation procedures since it is lodged at the left front part of the intake manifold. On the other hand, in case of V8 engines, you have to remove an engine cover to access the EVAP canister purge valve that is located at the top of rear intake manifold portion prior to disconnecting electrical connector and lines for removal and installation purposes. The EVAP canister vent solenoid located behind the left rear wheel well can be accessed by jacking up and securing the vehicle; disconnecting all electrical connectors, hoses then slide solenoid upward to remove or reinstall it. Finally, raising the vehicle disconnecting labeled hoses with electrical connectors then detaching it from its mounting bracket completes EVAP canister situated on top fuel tank's installation process. Above all, fuel tank pressure sensor atop fuel pump/fuel level sensor module mounting flange needs a raised motorcar body coupled with removal of fuel tank before eventually dismantling and reinstalling sensor by means of undoing electric plug.

After removing the fuel pump flow control module, you should install the new module in the reverse order of removal.

To install the high-pressure fuel line, clean the fittings, apply oil to the threads, and install the new high-pressure fuel line.

It is located behind the left rear wheel well and can be accessed by raising and securing the vehicle, disconnecting the electrical connector and hoses, and sliding the solenoid up for removal and reinstallation.

To replace the fuel pump flow control module, you need to disconnect the electrical connector and remove the three mounting bolts before removing the module from its bracket.

After raising the vehicle on jackstands, you should disconnect the electrical connector.

After raising the vehicle on jackstands, you should disconnect the electrical connector.

The first step is to relieve the system fuel pressure and raise the vehicle on jackstands.

You should tighten the fuel pressure sensor securely.