Make sure this part fits

Chevrolet 96069422 Cylinder Head

1994-1995 Chevrolet Tracker

Customer Questions & Expert Answers (6)
GM 96069422 Cylinder Head
  • Part Description
    Head,Cyl
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Chevrolet
    Manufacturer Part Number96069422
    Part DescriptionHead,Cyl
    Item Weight17.30 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU96069422
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1994-1995 Chevrolet Tracker4 Cyl 1.6L2 DOOR HARD TOP, CONVERTIBLE
  • Customer Questions & Expert Answers

    Q:
    I am wonder if this is complete and correct part for my vehicle. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 96069422 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to remove and reinstall a cylinder head on SOHC engine? Posted by Customer
    A:
    Allow the engine to cool completely before following this procedure. Position the number one piston at Top Dead Center. Disconnect the negative cable from the battery. Drain the cooling system and remove the spark plugs. Remove the intake manifold. Remove the exhaust manifold. Remove the distributor, including the cap and wires. On carbureted models, remove the fuel pump. Remove the timing belt. Remove the camshaft cover. On 16-valve engines, also remove the camshaft and intake rocker arms. Using a 14 mm socket, loosen the cylinder head bolts, 1/4-turn at a time, in the reverse of the sequence shown until they can be removed by hand. Carefully lift the cylinder head straight up and place the head on wooden blocks to prevent damage to the sealing surfaces. If the head sticks to the engine block, dislodge it by prying against a protrusion on the head casting. Note: Cylinder head disassembly and inspection procedures are covered in Part B. It's a good idea to inspect the camshaft and have the head checked for war page, even if you're just replacing the gasket. Remove all traces of old gasket material from the block and head. Do not allow anything to fall into the engine. Clean and inspect all threaded fasteners and be sure the threaded holes in the block are clean and dry. Place a new gasket and the cylinder head in position. The cylinder head bolts should be tightened in several stages following the proper sequence to the torque. Reinstall the timing belt. Reinstall the remaining parts in the reverse order of removal. Be sure to refill the cooling system and check all fluid levels. Rotate the crankshaft clockwise slowly by hand through two complete revolutions. Recheck the camshaft timing marks. Start the engine and set the ignition timing. Run the engine until normal operating temperature is reached. Check for leaks and proper operation. Shut off the engine, remove the camshaft cover and retorque the cylinder head bolts, unless the gasket manufacturer states otherwise. Recheck the valve adjustment.
    Posted by GMPartsGiant Specialist
    Q:
    How should the block and head be prepared for cylinder head installation for the 1999 Chevrolet Tracker? Posted by Customer
    A:
    Clean the block and head, install knock pins, and place a new gasket.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Cylinder Head
    Q:
    What are the essential steps for effectively cleaning a cylinder head and its associated components during an engine overhaul for the 1998 Chevrolet Tracker? Posted by Customer
    A:
    To effectively clean a cylinder head and associated components during an engine overhaul, follow these steps:Remove old gasket material and sealant from head gasket, intake manifold, and exhaust manifold surfaces.Clear accumulated scale from coolant passages.Eliminate deposits from holes using a stiff wire brush.Clean threaded holes with an appropriate-sized tap.Use compressed air to remove debris.Clean rocker arm shaft oil holes.Utilize solvent to clean and dry the cylinder head and components.Consider using caustic decarbonizing chemicals with caution.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Cylinder Head
    Q:
    How should the springs be compressed during installation for the 2001 Chevrolet Tracker? Posted by Customer
    A:
    Use a valve spring compressor to compress the springs.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Cylinder Head
    Q:
    What precautions should be taken when removing valves from a SOHC cylinder head for the 1994 Chevrolet Tracker? Posted by Customer
    A:
    Before removing valves from a SOHC cylinder head, arrange to label and store them, along with their related components, so they can be kept separate and reinstalled in the same valve guides they were removed from. Use a spring compressor to compress the springs, remove the keepers, then carefully release the compressor to remove the retainer, spring, spring seat, and valve. Also, remove the oil seal from the guide.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Cylinder Head
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 96069422, the Right Choice

To ensure reliability, purchase GM part # 96069422 Cylinder Head. It is sometimes referred to as Chevrolet Cylinder Head. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Chevrolet Tracker models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 96069422 Cylinder Head. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Chevrolet parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly