Make sure this part fits

Chevrolet 25990067 Caliper Assembly, Rear Brake (W/O Brake Pads & Bracket

2011-2016 Chevrolet Impala

Customer Questions & Expert Answers (2)
GM 25990067 Caliper Assembly, Rear Brake (W/O Brake Pads & Bracket
  • Part Description
    CALIPER, Wheel Brake Cylinder/Caliper
  • Position
    Rear
  • Replaces
    18048684, 88965582
  • Manufacturer
    General Motors
Make sure this part fits
$111.51 MSRP: $219.58
You Save: $108.07 (50%)
Core Charge: $40.00
Ships in 1-2 Business Days
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Chevrolet
    Manufacturer Part Number25990067
    Part DescriptionCALIPER, Wheel Brake Cylinder/Caliper
    Other NamesCaliper
    Item Dimensions9.1 x 8.2 x 6.1 inches
    Item Weight7.40 Pounds
    PositionRear
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces18048684, 88965582
    ManufacturerGeneral Motors
    SKU25990067
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2011-2016 Chevrolet Impala6 Cyl 3.5L Flex, 6 Cyl 3.6L, 6 Cyl 3.9L FlexLS, LTZ
  • Customer Questions & Expert Answers

    Q:
    I would like to confirm if this is the correct part number for my vehicle. Please advise. Thank you. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 25990067 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to remove and install brake calipers? Posted by Customer
    A:
    Dust created by the brake system is harmful to your health. Never blow it out with compressed air and don't inhale any of it. An approved filtering mask should be worn when working on the brakes. Do not, under any circumstances, use petroleum-based solvents to clean brake parts. Use brake system cleaner only. If replacement is indicated (usually because of fluid leakage), it is recommended that the calipers be replaced, not overhauled. New and factory rebuilt units are available on an exchange basis, which makes this job quite easy. Always replace the calipers in pairs-never replace just one of them. This procedure applies to front and rear disc brakes. Removal: Loosen the wheel lug nuts, raise the end of the vehicle you're working on and support it securely on jack stands. Block the wheels at the opposite end. Remove the wheels. Depress the caliper piston with a C-clamp just enough to allow the pad to clear the disc (On front brakes and rear brakes with parking brake shoes (instead of actuator-type calipers), depress the caliper pistons into the bottom of their bores with a large C-clamp). Caution: Do not attempt to depress the piston into the caliper on later models with parking brake actuator-type calipers. Disconnect the brake line from the caliper and plug it to keep contaminants out of the brake system and to prevent losing any more brake fluid than is necessary (Brake caliper mounting details: Brake line fitting Caliper mounting bolts Caliper mounting bracket bolts). Note: If you're simply removing the caliper for access to other components, don't disconnect the brake line from the caliper. Remove the caliper mounting bolts (or guide pins on rear calipers). Note: On front calipers, hold the guide pin with a wrench to remove the mounting bolts (Hold the guide pin with one wrench while removing the lower caliper mounting bolt with another). Detach the caliper from its mounting bracket. Installation: Install the caliper by reversing the removal procedure. Remember to replace the copper sealing washers on either side of the brake line fitting with new ones. Tighten the caliper mounting bolts and the brake line banjo fitting bolt to the torque. Bleed the brake system. Install the wheels and lug nuts and lower the vehicle. Tighten the wheel lug nuts to the torque. Check the operation of the brakes thoroughly before placing the vehicle into normal service.
    Posted by GMPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 25990067, the Right Choice

To ensure reliability, purchase GM part # 25990067 Caliper Assembly, Rear Brake (W/O Brake Pads & Bracket. It is sometimes referred to as Chevrolet Brake Calipers. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Chevrolet Impala models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 25990067 Caliper Assembly, Rear Brake (W/O Brake Pads & Bracket. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Chevrolet parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly