Chevrolet 22847703 Rear Axle Assembly (3.42 Ratio)

You can Select Your Vehicle to check if 22847703 fits your vehicle.

After removing the differential cover, you need to remove the pinion shaft lock screw and withdraw the pinion shaft.

The final step is to tighten the wheel lug nuts to the proper torque specifications.

The initial steps to remove and install components in the front differential of selectable 4WD systems are as follows: Loosen the wheel lug nuts. Raise the vehicle securely on jackstands. Remove the right front wheel. Remove the differential carrier splash shield if equipped. Drain the lubricant from the front differential. For 4WD systems, unbolt the right driveaxle from the axleshaft flange and support it out of the way. Remove the front axle shift motor and, if applicable, disconnect the front stabilizer link or remove the front shock absorber/coil spring assembly. On 2500/3500 models, remove the front axle bracket bolts and slide the bracket forward for additional clearance. Support the differential carrier with a floor jack and a block of wood.

The initial steps are to loosen the rear wheel lug nuts, raise the rear of the vehicle, and support it securely on jackstands.

It is important to inspect the boots periodically for damage and leaking lubricant, as torn CV joint boots must be replaced immediately to prevent damage to the joints.

When diagnosing axle problems, it is important to check for other possible causes such as road or tire noise, and to isolate engine and transmission noises.

For models with a locking differential, you should rotate the differential until the shaft touches the case for access to the C-locks.

After raising the vehicle and supporting it on jackstands, a jack should be positioned under the rear axle differential housing.

Before installing the driveaxle, the splines on the stub shaft should be lubricated with multi-purpose grease.

The drive axle-to-axle shaft flange bolts should be removed while having an assistant apply the brake to prevent the driveaxle from turning.

No, overhauling the differential requires special tools and is not cost-effective for a do-it-yourselfer.

The initial steps to remove and install components in the front differential of selectable 4WD systems are as follows: Loosen the wheel lug nuts. Raise the vehicle securely on jackstands. Remove the right front wheel. Remove the differential carrier splash shield if equipped. Drain the lubricant from the front differential. For 4WD systems, unbolt the right driveaxle from the axleshaft flange and support it out of the way. Remove the front axle shift motor and, if applicable, disconnect the front stabilizer link or remove the front shock absorber/coil spring assembly. On 2500/3500 models, remove the front axle bracket bolts and slide the bracket forward for additional clearance. Support the differential carrier with a floor jack and a block of wood.

It is also important to check the driveaxle shafts for cracks, dents, and distortion.

To remove and install components in the front differential for AWD systems, follow these steps:Remove the stabilizer bar link and, if applicable, the front shock absorber.

For leaf spring models, the spring U-bolts should be disconnected, followed by removing the springplates. Then, the jack can be lowered under the differential to remove the rear axle assembly.

After removing the differential cover, you need to remove the pinion shaft lock screw and withdraw the pinion shaft.

To check for wear in the CV joints and driveaxle shafts, grasp each axle and rotate it in both directions while holding the CV joint housings, feeling for play indicating worn splines or sloppy CV joints.

The differential allows the outer rear wheel to turn at a higher speed than the inner tire when going around a corner.

The outer ends of the driveaxles are equipped with ball-and-cage type CV joints capable of angular but not axial movement.

The initial steps to remove and install components in the front differential of selectable 4WD systems are as follows: Loosen the wheel lug nuts. Raise the vehicle securely on jackstands. Remove the right front wheel. Remove the differential carrier splash shield if equipped. Drain the lubricant from the front differential. For 4WD systems, unbolt the right driveaxle from the axleshaft flange and support it out of the way. Remove the front axle shift motor and, if applicable, disconnect the front stabilizer link or remove the front shock absorber/coil spring assembly. On 2500/3500 models, remove the front axle bracket bolts and slide the bracket forward for additional clearance. Support the differential carrier with a floor jack and a block of wood.

The initial steps are to loosen the rear wheel lug nuts, raise the rear of the vehicle, and support it securely on jackstands.

The next step is to drain the differential lubricant and remove the differential cover.

If the vehicle has a differential carrier splash shield, it should be removed after removing the driveaxle/hub nut.

4WD models use a fully independent front axle assembly.