Make sure this part fits

Cadillac 84008848 Front Lower Control Arm Assembly

2013-2019 Cadillac XTS

Customer Questions & Expert Answers (2)
GM 84008848 Front Lower Control Arm Assembly
  • Part Description
    Arm Assembly, Front Lwr Cont
  • Position
    Front Lower
  • Replaces
    84248218, 23121590
  • Manufacturer
    General Motors
Make sure this part fits
$132.48 MSRP: $230.61
You Save: $98.13 (43%)
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Cadillac
    Manufacturer Part Number84008848
    Part DescriptionArm Assembly, Front Lwr Cont
    Other NamesLower Control Arm
    Item Dimensions28.6 x 12.7 x 3.1 inches
    Item Weight6.30 Pounds
    PositionFront Lower
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces84248218, 23121590
    ManufacturerGeneral Motors
    SKU84008848
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2013-2019 Cadillac XTS6 Cyl 3.6L4 DOOR NOTCHBACK, LUXURY 4 DOOR NOTCHBACK, PLATINUM 4 DOOR NOTCHBACK, PREMIUM 4 DOOR NOTCHBACK
  • Customer Questions & Expert Answers

    Q:
    Do these parts fit my vehicle? Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 84008848 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How do I remove and replace the control arm? Posted by Customer
    A:
    To remove the control arm for 2009 and earlier models, mark the relationship of the control arm to the subframe while the vehicle is at normal ride height. The front wheel is removed after loosening the wheel lug nuts and raising the front of the vehicle on jackstands. If available, unplug or pull out of place ABS wheel speed sensor and harness from its position within control arm. After that, separate balljoint from steering knuckle and remove some fasteners connecting control arm with this subframe. In order to verify if there are any distortions or worn out parts, inspect the control arm and bushings checking for any damage which should be replaced only if damaged.Since all bolts were tight when they got installed, loosen them first before removing them during installation until you get them in numbers that do not exceed fifteen per square inch; alternatively use a torque wrench set between twenty five foot-pounds (25 ft lbs) and forty-five ft-lbs.For removal with GNB front suspension models 2010 onwards one has to look at how they can release front wheels' nuts loosen jack up their cars using jacks stands take away tires from axles disconnect height sensor plus w/harness then follow it up by undoing rear bushing-to-subframe fasteners nut bolt yoke on strut as well pawl finally unscrewed under front bracket above whole assembly install reverse new bolts are used tighten as per instruction manual.In case of GNA front suspension models 2010 onwards, one has to look at how they can release front wheels' nuts loosen jack up their cars using jacks stands take away tires from axles detach flange connector in addition pinch-bolt that joins two in proximity strucker others back pads allowing connection between shock absorber shaft end ears mountings would still remain intact otherwise pressed down farther rearwardly just behind inside bore wall underneath rubber disc small metal part lining onto other side only through existing hole inside upper lip separate bushing located near large bottom surface is pushed outwards at same time lower one goes inwards similarly cm beside main body over which will be positioned adequate space between two components because it's here your tool needs to get locked up against case we're discussing about repair field technicians won't this without certain knowledge concerning difficulty involved.To remove the control arm, special tools are necessary and it is recommended for the control arm to be taken for bushing replacement.
    Posted by GMPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 84008848, the Right Choice

To ensure reliability, purchase GM part # 84008848 Front Lower Control Arm Assembly. It is sometimes referred to as Cadillac Control Arm. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Cadillac XTS models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 84008848 Front Lower Control Arm Assembly. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Cadillac parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly