Make sure this part fits

Cadillac 20765171 Front Shock Absorber Assembly

2007-2010 Cadillac Escalade

Customer Questions & Expert Answers (19)
GM 20765171 Front Shock Absorber Assembly
  • Part Description
    Absorber Assembly, Front Shock ; Absorber, Front And Rear Suspension
  • Position
    Front
  • Replaces
    20813217, 25871217, 25876832, 15846889
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Cadillac
    Manufacturer Part Number20765171
    Part DescriptionAbsorber Assembly, Front Shock ; Absorber, Front And Rear Suspension
    Other NamesShock, Strut
    Item Dimensions26.5 x 6.1 x 6.2 inches
    Item Weight6.90 Pounds
    PositionFront
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces20813217, 25871217, 25876832, 15846889
    ManufacturerGeneral Motors
    SKU20765171
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2007-2010 Cadillac Escalade8 Cyl 6.0L, 8 Cyl 6.0L Flex, 8 Cyl 6.2L, 8 Cyl 6.2L Flex1/2 TON, EXT 1/2 TON, YUKON XL/DENALI XL/ESCALADE ESV, YUKON/DENALI/ESCALADE
  • Customer Questions & Expert Answers

    Q:
    I would like to confirm if this is the correct part number for my vehicle. Please advise. Thank you. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 20765171 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    What should be done if fluid leakage is observed for the 2013 Chevrolet Avalanche? Posted by Customer
    A:
    If leakage is noted, it's advisable to replace the shocks as a set.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How do you remove the 2009 Chevrolet Avalanche? Posted by Customer
    A:
    Start by loosening the front wheel lug nuts, raising the vehicle, and removing the wheel. Support the outer end of the lower control arm with a floor jack and detach the tie-rod end from the steering knuckle. Remove the upper mounting nuts and the two bolts that attach the lower end of the shock absorber to the lower control arm. Pull the shock out from below.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How can the shock absorber be installed for the 2013 Chevrolet Avalanche? Posted by Customer
    A:
    The shock absorber can be installed by reversing the removal steps and tightening the fasteners to the torque specifications.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How do you remove the 2013 Chevrolet Tahoe? Posted by Customer
    A:
    Follow the same steps as removing the coil-over shock absorber model, but use a backup wrench on the stem to remove the upper mounting nut and related hardware. Remove the lower mounting nut and bolt, noting the direction in which the bolt points.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What is the first step to remove the shock absorber from the 2007 Chevrolet Suburban? Posted by Customer
    A:
    The first step is to raise the rear of the vehicle and support it securely on jackstands placed underneath the frame rails.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What should be done to prevent the 2012 GMC Sierra from rolling off the stands? Posted by Customer
    A:
    The front wheels should be blocked to prevent the vehicle from rolling off the stands.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What should be done if the 2008 Chevrolet Tahoe is equipped with a ride control system? Posted by Customer
    A:
    If the vehicle is equipped with a ride control system, the electrical connector and the airline should be disconnected from the shock absorber.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What are the initial steps for inspecting 2007 Chevrolet Silverado suspension and shocks? Posted by Customer
    A:
    Start by parking the vehicle on level ground, turning off the engine, and setting the parking brake. Check the tire pressures. Push down at one corner of the vehicle and then release it while noting the movement of the body. It should stop moving and come to rest in a level position within one or two bounces.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How do you install the 2007 Chevrolet Suburban? Posted by Customer
    A:
    To install, reverse the removal steps and tighten the mounting fasteners to the torque specifications. If equipped with a suspension control system, reconnect the electrical connector to the top of the shock absorber.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    Besides leakage, what should you inspect on the shocks for the 2012 Chevrolet Suburban? Posted by Customer
    A:
    Inspect the shocks to ensure they are securely mounted and undamaged. Check the upper mounts for damage and wear.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How do you install the coil-over shock absorber2013 Chevrolet Silverado? Posted by Customer
    A:
    To install, reverse the removal steps and tighten the mounting fasteners to the torque specifications. If equipped with a suspension control system, reconnect the electrical connector to the top of the shock absorber.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How can you check for movement at the steering knuckle-to-control arm balljoint for the 2007 Chevrolet Tahoe? Posted by Customer
    A:
    Have an assistant grasp the lower edge of the tire and move the wheel in and out while you look for movement at the steering knuckle-to-control arm balljoint. If there is any movement, the suspension balljoint(s) must be replaced.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How should the rear axle be supported during the removal process of the 2013 Chevrolet Silverado? Posted by Customer
    A:
    The rear axle should be supported with a floor jack placed under the axle tube closest to the shock absorber being removed.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What might be the issue if the 2013 GMC Sierra continues to move up and down or fails to return to its original position? Posted by Customer
    A:
    If the vehicle continues to move up and down or fails to return to its original position, it may indicate a worn or weak shock absorber.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How do you install the 2012 GMC Sierra? Posted by Customer
    A:
    To install, reverse the removal steps and ensure the lower mounting bolt is pointing in the same direction as before.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How do you install the 2008 GMC Yukon? Posted by Customer
    A:
    To install, reverse the removal steps and tighten the mounting fasteners to the torque specifications. If equipped with a suspension control system, reconnect the electrical connector to the top of the shock absorber.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What might be the issue if the 2014 GMC Yukon continues to move up and down or fails to return to its original position? Posted by Customer
    A:
    If the vehicle continues to move up and down or fails to return to its original position, it may indicate a worn or weak shock absorber.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What should be done after supporting the rear axle for the 2011 GMC Yukon? Posted by Customer
    A:
    After supporting the rear axle, the shock absorber upper and lower mounting fasteners should be removed.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shock Absorber
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 20765171, the Right Choice

To ensure reliability, purchase GM part # 20765171 Front Shock Absorber Assembly. It is sometimes referred to as Cadillac Shock Absorber. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Cadillac Escalade models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 20765171 Front Shock Absorber Assembly. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Cadillac parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly