Buick 11588728 Bolt, Heavy Hx Acorn Flange Head

You can Select Your Vehicle to check if 11588728 fits your vehicle.

Remove the spark plugs and the valve covers, camshafts and rocker arms. Thread an adapter into the spark plug hole and connect an air hose from a compressed air source to it. Most auto parts stores can supply the air hose adapter. Apply compressed air to the cylinder. The valves should be held in place by the air pressure. Using a socket and a hammer, gently tap on the top of each valve spring retainer several times, then use a valve-spring compressor to compress the spring. Remove the keepers with small needle-nose pliers or a magnet. Remove the valve spring and retainer. Remove the old Valve Stem Oil Seals, noting differences between the intake and exhaust seals. Wrap a rubber band or tape around the top of the valve stem so the valve won't fall into the combustion chamber, then release the air pressure. Inspect the valve stem for damage. Rotate the valve in the guide and check the end for eccentric movement. Move the valve up-and-down in the guide and make sure it does not bind. Reapply air pressure to the cylinder to retain the valve in the closed position, then remove the tape or rubber band from the valve stem. If you're working on an exhaust valve, fit the new exhaust Valve Stem Oil Seal on the valve stem and press it down over the valve guide. If you're working on an intake valve, install a new intake Valve Stem Oil Seal over the valve stem and press it down over the valve guide. Install the spring and retainer in position over the valve. Compress the valve spring assembly only enough to install the keepers in the valve stem. Position the keepers in the valve stem groove. Apply a small dab of grease to the inside of each keeper to hold it in place if necessary. Remove the pressure from the spring tool and make sure the keepers are seated. Disconnect the air hose and remove the adapter from the spark plug hole. Repeat the above procedure on the remaining cylinders. Install the rocker arm assemblies, camshafts, timing chains and the valve covers. Start the engine, then check for oil leaks and unusual sounds coming from the valve cover area. Allow the engine to idle for at least five minutes before revving the engine.

To start with, rotate the crankshaft until the number one piston is at Top Dead Center on the compression stroke. Put an adaptor into the spark plug hole and connect an air hose from a compressed air source to it. Then you apply compressed air to the cylinder to hold the valves in place. Prevent any parts or tools from falling into the engine by stuffing shop rags into the cylinder head holes around the valves. Tap gently on top of each valve spring retainer with a socket and hammer in order to break the seal between the valve keeper and the spring retainer. Use a small pair of needle nose pliers or a magnet to remove keepers compressed spring using valve-spring compressor. Remove both spring and retainer then replace old valve stem seals. Check whether there is any damage on the valve stem or eccentric movement or binding. If necessary, remove head for repair. Press new stem seals over valve guide until they are at specified depth. Install keepers in valve stem grooves by compressing spring and placing retainers then drop them in said sequence if need be use grease literally just to stick them down tiny bit of grease will do it this time if needed at all . Follow this process for other cylinders in line with their firing order sequence as shown below: Finally, reinstall rocker arm assemblies and valve covers; start engine, check for oil leaks or any other unusual sounds that may be heard from it. Leave engine idling for at least five minutes before revving it.

To replace the Valve Stem Oil Seals, start by removing the valve cover(s) from the cylinder head(s), and if replacing all seals, remove all spark plugs too. If replacing all seals, go according to firing order (1-6-5-4-3-2) and begin with cylinder number 1 i.e. skip 120 degrees clockwise for each cylinder. Position the piston in that selected cylinder at Top Dead Center on the compression stroke by rotating the crankshaft. For that target cylinder head, remove all rocker arms, pushrods, and support bars. Screw an adapter into the spark plug hole and attach a compressed air source which applies approximately 90 to 100 psi of pressure to retain valves position. Shop rags should be inserted into the holes on top of the cylinder heads to prevent foreign objects from entering into the engine. A removal tool such as a valve spring compressor can help compress retainers together with valve springs thus allowing keepers' elimination. Old Valve Stem Oil Seal is then taken out after getting rid of spring retainer or rotator together with its assembly. Keep the rubber band or tape on hand for holding down the valve stem so that it does not fall out when releasing air pressure later on. While installing, ensure there is no damage on valve stem but it moves freely in guide without sticking inside it. Air pressure should be reapplied to hold down the valve while taking off tape or rubber bands. After applying some engine oil for lubrication purposes around the stem ends of valves install new seals after tapping them gently with a deep socket or tool used for installation of a seal into place, care being taken not to twist or cock these seals in any way at this point also check if garter spring is properly positioned around the top of each seal before proceeding further with the installation process of valve spring and damper if applicable closely-wound spring coils facing towards cylinder head while securing either rotator or retainer for valve spring. Disconnect the air hose, remove the adapter from the spark plug hole, and repeat the process for the remaining cylinders, aligning each piston with TDC on the compression stroke. Finally, reinstall the rocker arms, support bars, and pushrods, followed by the valve cover(s), spark plug(s), and wires, and start and run the engine, checking for any oil leaks or unusual noises from the valve cover area.

Finally, reinstall the rocker arms, support bars, and pushrods, followed by the valve cover(s), spark plug(s), and wires.