How to remove and install Door Lock Cylinder,Door Latch Assembly and Door Handle?

To remove and install the front and back doors, perform the steps below. Start by raising the window, then detach the door trim panel and water shield. To avoid damaging the paintwork, carefully remove the door handle cover on the outside of the door. Then, remove the door outer panel. Remove rivets and disconnect handle linkage then take out handle mechanism from door. Move forward with door from inside while at it slide it so that you can remove actuating rod from lever of your door handle and pull out front lock rod to disconnect it from latch mechanism. Disconnect actuating rods on each side of latch mechanism from both sides of bolt lower part of jamb on which a door sits. Pull window run channel back down until it is clear of window then release upper weather strip to allow room for upward movement of glass panel. After disconnecting wires from latch mechanism, remove Door Latch Assembly mounting bolts and turn latch mechanism outward through hole in door access opening. If you haven't done so already, take off clip that holds lock cylinder rod in place before removing lock cylinder from within door frame itself. Reinstall in reverse order remembering to replace lock rod retainers after removal is done. For rear doors do this process by raising window first; next remove trim panel and water shield on a door; thirdly get rid of handle covers, outer panels for doors as well as their handles linked to them together with small screws; furthly slide inside a leftward-opening car or truck's bathroom member beneath around such some way indirectly behind between pushing her out beyond your own fingers at their owner's hand; moreover insert your fingers into position against an inwardly-facing rightward-facing one; finally pull forwards past where all those things belong even if out along its path until connected lines snap apart causing front end locks unlocked opening them upwards then unhooking any more electric controls (if necessary) after completely marking location where they are situated around these devices while removing each and every one of them too especially when discharging these assemblies via actuator screws so now bolts attached outside walls near tops including reinstallation procedures involving loosing up retainer clips until sliding back out again following their exits' orders without forgetting about everything else associated throughout lock's construction because that would prevent you from slamming door shut. For the rear door, do the same as described above. First of all, raise the window then take off the door trim panel and water shield. Remove door handle cover, door outer panel, rivets, and handle mechanism. Inside the door, slide the door handle forward and unlatch the actuating rod, then pull out and disconnect the front lock rod. Unhook the door handle actuating rod and remove the bolts from the window run channel. Remove foam insulator, weatherstrip mounting screws and pull rearwardly weather strip out. Disconnect electrical connectors from latch mechanism then mark actuating rods for reinstallation hence remove them. Remove Door Latch Assembly mounting bolts in reverse order then angle latch mechanism out of access hole on a car's entrance; finally replacing any needed lock rod retainers before reassembling everything into place once more if necessary.

Genuine Saturn LS Door Handle

Inside Door Handle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

29 Door Handles found

View related parts
Saturn LS Handle Asm,Front Side Door Pull *Medium Duty Dark.Pewter
Part Number: 22672469
$50.68 MSRP: $83.88
You Save: $33.20 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Front Door Trim; Pull Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Strap,Roof Rail Rear Asst *Opel Gray
Part Number: 90440502
$14.36 MSRP: $24.53
You Save: $10.17 (42%)
ADD TO CART
Product Specifications
- Other Name: HANDLE, Rear Quarter and Roof Rail Assist; Assist Strap
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Assembly, Rear Side Door Pull *Medium Duty Dark.Pewterr
Part Number: 24427349
$17.31 MSRP: $44.64
You Save: $27.33 (62%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Rear Side Door Trim Finish; Pull Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Front Side Door Inside *Medium Duty Dark Oak
Part Number: 22674213
$14.28 MSRP: $21.35
You Save: $7.07 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Front Side Door Inside *Ebony
Part Number: 22674217
$42.14 MSRP: $63.00
You Save: $20.86 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle, Inside; Inside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle,Front Side Door Outside *Unpainted
Part Number: 22686786
$15.63 MSRP: $25.43
You Save: $9.80 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Front Side Door Pull *Medium Duty Dark Oak
Part Number: 22672461
$55.65 MSRP: $81.56
You Save: $25.91 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Front Door Trim; Pull Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Assembly, Rear Side Door Pull *Medium Duty Dark Oak
Part Number: 24427347
$30.94 MSRP: $36.06
You Save: $5.12 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Rear Side Door Trim Finish; Pull Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Assembly, Rear Side Door Pull *Medium Duty Dark.Pewterr
Part Number: 24427352
$19.24 MSRP: $22.42
You Save: $3.18 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Rear Side Door Trim Finish; Pull Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Assembly, Rear Side Door Pull *Medium Duty Dark Oak
Part Number: 24427350
Product Specifications
- Other Name: HANDLE, Rear Side Door Trim Finish; Pull Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Front Side Door Inside *Medium Duty Dark Oak
Part Number: 22674214
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle,Front Side Door Outside *Black
Part Number: 22686772
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Lift Gate Inside Pull *Light Oak
Part Number: 90440506
Product Specifications
- Other Name: HANDLE, Rear Compartment Lift Window / Lift Gate / End Gate; Pull Handle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Lift Gate Inside Pull *Medium Duty Dark.Pewter
Part Number: 90440507
Product Specifications
- Other Name: HANDLE, Rear Compartment Lift Window / Lift Gate / End Gate; Pull Handle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Strap,Roof Rail Front Asst *Light Oak
Part Number: 90440501
Product Specifications
- Other Name: HANDLE, Rear Quarter and Roof Rail Assist; Assist Strap
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Rear Side Door Inside *Medium Duty Dark.Pewter
Part Number: 22674233
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Rear Side Door Inside *Medium Duty Dark Oak
Part Number: 22674225
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Rear Side Door Inside *Medium Duty Dark Oak
Part Number: 22674226
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Rear Side Door Inside *Ebony
Part Number: 22674229
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L
View related parts
Saturn LS Handle Asm,Rear Side Door Inside *Ebony
Part Number: 22674230
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L, 6 Cyl 3.0L

| Page 1 of 2 |Next >

1-20 of 29 Results

Saturn LS Door Handle

The Door Handle of Saturn LS vehicles provides the vital added functionality of the door opening through provided handle to get into the vehicle. Made from plastic or metal material, this handle is pivoted on a metal shaft that on a pull operation triggers the door latch. This mechanism guarantees the opportunity of getting in without worrying about particularities, which adds to the general pleasantness of the auto. Although the overview does not name other styles or types of the Door Handle installed on the Saturn LS vehicles it highlights their usefulness in day to day usage. This assures that the handles are able to stay strong even under extreme climate and are also able to withstand abuse normally associated with handling. As any other objects, door handles might be damaged from time to time even if the commercial ones are quite durable, so their periodic replacement might be needed.

Each OEM Saturn LS Door Handle we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Saturn LS Door Handle Parts Questions & Experts Answers

Handle Asm,Front Side Door Inside *Medium Duty Dark Oak
22674213
Q: How to remove and install Door Lock Cylinder,Door Latch Assembly and Door Handle?
A: To remove and install the front and back doors, perform the steps below. Start by raising the window, then detach the door trim panel and water shield. To avoid damaging the paintwork, carefully remove the door handle cover on the outside of the door. Then, remove the door outer panel. Remove rivets and disconnect handle linkage then take out handle mechanism from door. Move forward with door from inside while at it slide it so that you can remove actuating rod from lever of your door handle and pull out front lock rod to disconnect it from latch mechanism. Disconnect actuating rods on each side of latch mechanism from both sides of bolt lower part of jamb on which a door sits. Pull window run channel back down until it is clear of window then release upper weather strip to allow room for upward movement of glass panel. After disconnecting wires from latch mechanism, remove Door Latch Assembly mounting bolts and turn latch mechanism outward through hole in door access opening. If you haven't done so already, take off clip that holds lock cylinder rod in place before removing lock cylinder from within door frame itself. Reinstall in reverse order remembering to replace lock rod retainers after removal is done. For rear doors do this process by raising window first; next remove trim panel and water shield on a door; thirdly get rid of handle covers, outer panels for doors as well as their handles linked to them together with small screws; furthly slide inside a leftward-opening car or truck's bathroom member beneath around such some way indirectly behind between pushing her out beyond your own fingers at their owner's hand; moreover insert your fingers into position against an inwardly-facing rightward-facing one; finally pull forwards past where all those things belong even if out along its path until connected lines snap apart causing front end locks unlocked opening them upwards then unhooking any more electric controls (if necessary) after completely marking location where they are situated around these devices while removing each and every one of them too especially when discharging these assemblies via actuator screws so now bolts attached outside walls near tops including reinstallation procedures involving loosing up retainer clips until sliding back out again following their exits' orders without forgetting about everything else associated throughout lock's construction because that would prevent you from slamming door shut. For the rear door, do the same as described above. First of all, raise the window then take off the door trim panel and water shield. Remove door handle cover, door outer panel, rivets, and handle mechanism. Inside the door, slide the door handle forward and unlatch the actuating rod, then pull out and disconnect the front lock rod. Unhook the door handle actuating rod and remove the bolts from the window run channel. Remove foam insulator, weatherstrip mounting screws and pull rearwardly weather strip out. Disconnect electrical connectors from latch mechanism then mark actuating rods for reinstallation hence remove them. Remove Door Latch Assembly mounting bolts in reverse order then angle latch mechanism out of access hole on a car's entrance; finally replacing any needed lock rod retainers before reassembling everything into place once more if necessary.

Related Saturn LS Parts

Browse by Year

2000 Door Handle