My Garage
My Account
Cart
Genuine Pontiac Vibe Coil Springs
Strut Spring- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
11 Coil Springs found
Pontiac Vibe Front Springs
Part Number: 88970153$43.41 MSRP: $87.54You Save: $44.13 (51%)Ships in 1-2 Business Days
Pontiac Vibe Rear Spring
Part Number: 19184408$94.66 MSRP: $131.95You Save: $37.29 (29%)Ships in 1-2 Business Days
Pontiac Vibe Rear Spring
Part Number: 19184407$88.89 MSRP: $131.95You Save: $43.06 (33%)Ships in 1-2 Business Days
Pontiac Vibe Front Springs
Part Number: 19184395$39.33 MSRP: $50.07You Save: $10.74 (22%)Ships in 1-2 Business DaysPontiac Vibe Front Springs
Part Number: 19184399$39.92 MSRP: $50.84You Save: $10.92 (22%)Ships in 1-2 Business Days
Pontiac Vibe Rear Spring
Part Number: 88972249$99.65 MSRP: $131.95You Save: $32.30 (25%)Ships in 1-2 Business Days
Pontiac Vibe Coil Springs
Coil springs are found to be used in the suspension of the Pontiac Vibe vehicles where they are tasked with carrying the weight of the car as well as shock coming from the ground. These coil springs acts as shock absorbers which allow the car to maintain correct height, alignment of the wheels as well as correcting situations like abnormal wearing of tires and bottoming. Different coil springs have been used in different years in the models of Pontiac Vibe including linear rate springs, progressive springs as well as the dual rate springs. Linear rate springs deliver the same stiffness independently of the load and the load piled on them while progressive springs absorb effectively the load, providing bigger stiffness when the loads increase. Micro-lite II key springs have two different rates for better outcome. Also, variable coil springs can be found which enables a certain ride height in order to accommodate the wheel and tire combinations. In general, the coil springs of the Pontiac Vibe automobiles have proved to work effectively in providing the optimal balance and comfort during operations.
Each OEM Pontiac Vibe Coil Springs we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Pontiac Vibe Coil Springs Parts Questions & Experts Answers
- Q: What steps should be followed for disassembling and reassembling strut or coil spring assemblies on Pontiac Vibe?A: Look under the hood for any leakages, loss of damping ability or any form of physical damage on the struts or coil springs before a job is done because these units are non-serviceable and have to be replaced once there is a problem. While strut assemblies with springs commonly are used, these parts may be ordered on an exchange basis, which is convenient. So before getting into the process of dismantling the vehicle, get to know the prices of Body parts and if they are easily available. To disassemble, the Strut assembly or rear shock absorber/coil spring assembly is removed and then mounted on a vise-the jaws of which are covered with wood or rags not to pinch the absorber/spring. After using a tool manufacturer's instruction place a spring compressor over the upper spring seat and get a confirmation when the pressure from the spring is relieved by jiggling the spring. Locate the position of the upper and lower spring seat and suspension support bracket, and then remove the damper shaft nut, and lock it if needed. Take out the nut and suspension support, it is necessary that you turn the bearing and observe its condition and check the rubber part of the support for signs of wearing. Raise the spring seat together with the upper insulator off the shaft of the damper and inspect the rubber spring seat for signs of wear. It is advisable to have the ends of the compressed spring facing your body's direction; then ease it off the assembly and place it aside securely. Next, slide the rubber bumper off the damper shaft and look at the condition of the lower insulator to see if it needs to be replaced. For reassembly, if replacing the lower insulator, insert it on the location and fitting, extend the damper rod to placing the rubber bumper. Position the coil spring on the lower insulator with the end slot of it devoted to the recessed part. Next screw in the upper insulator followed by the spring seat by ensuring that the flats on the damper shaft fit into the corresponding ones in the spring seat. Install the dust seal and suspension support so that their marks are the same when aligned and bolt the suspension support to the frame using a new nut and tighten. Last, either reinstall the strut assembly/ or the rear shock absorber and coil spring in the same manner as described above.
