When and how to replace the Coolant Temperature Sensor for Buick Skylark,Oldsmobile Omega and Pontiac Phoenix?

The coolant temperature indicator system includes an instrument panel lamp and a coolant temperature sensor or sender, situated at the left rear of the cylinder head on L4 engines, and at the rear of the right head on V6 engines. In place of a temperature sensor, the transducer replaces it if a temperature gauge is used on the instrument cluster. Where there is unusual indication or fault development, check first the coolant level in the system and then ensure that connecting wiring between gauge and sender unit is secure. When turning the ignition switch to the ON position with the starter motor turning, the indicator lamp should be illuminated (Overheated engine indication). The lamp may not be lit if; the bulb is burned out, the ignition switch is faulty or the circuit is open. Once the engine starts, the lamp should go out and remain so unless it overheats. The lamp may fail to go out because of a defective temperature sender unit or a faulty ignition switch or grounded wiring between the lamp and the sender unit. If you were going to change this Sensor unit, it would simply be unscrewed from the cylinder head after which another one could be installed in its place. There will be some loss of coolant so check levels after replacement has been installed.

Genuine Pontiac Phoenix Coolant Temperature Sensor

Coolant Water Temperature Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Coolant Temperature Sensors found

View related parts
Pontiac Phoenix Sensor Asm,Engine Coolant Temperature Gage
Part Number: 10045847
$38.92 MSRP: $73.46
You Save: $34.54 (48%)
ADD TO CART
Product Specifications
- Other Name: SENSOR, Computer Control Sensors; Coolant Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Pontiac Phoenix | 2 DOOR, 4 DOOR, LJ 2 DOOR, LJ 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
View related parts
Pontiac Phoenix Switch,Fan Control
Part Number: 3040674
Product Specifications
- Other Name: SWITCH, Engine Air Cooling(Electrical); Fan Switch, Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Pontiac Phoenix | 2 DOOR, 4 DOOR, LJ 2 DOOR, LJ 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
View related parts
Pontiac Phoenix Switch Asm,Efe Heater Engine Coolant Temperature
Part Number: 25036601
Product Specifications
- Other Name: SWITCH; Coolant Temperature Switch, EFE Temperature Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Pontiac Phoenix | 2 DOOR, 4 DOOR, LJ 2 DOOR, LJ 4 DOOR | 6 Cyl 2.8L
View related parts
Pontiac Phoenix Sensor Assembly, Engine Wtr Temperature(1 Terminal)
Part Number: 8993146
Product Specifications
- Other Name: SENSOR; Temperature Sending Unit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Pontiac Phoenix | 2 DOOR, 4 DOOR, LJ 2 DOOR, LJ 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
View related parts
Pontiac Phoenix Switch Pkg, Coolant Temperature
Part Number: 25036371
Product Specifications
- Other Name: SWITCH, Coolant Temperature (Engine Unit); Temperature Sending Unit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Pontiac Phoenix | 2 DOOR, 4 DOOR, LJ 2 DOOR, LJ 4 DOOR | 4 Cyl 2.5L

Pontiac Phoenix Coolant Temperature Sensor

The Coolant Temperature Sensor is a very vital component in any vehicle, and in the Pontiac Phoenix especially it will monitor the temperature of the coolant so that the engine will be running optimally. DTIM delivers information which is crucial in maintaining the control of the performance and fuel efficiency of the engine. Different model cars of Phoenix may have used Coolant Temperature Sensors of different kinds over the years, whereby different types might look different or be based on different technology but all perform the basic role of the component. Such deviations may impact on the extent to which it detects and reports temperature to the Engine control unit. In conclusion, the Coolant Temperature Sensor is significantly important to the health and efficiency of the engine in Pontiac Phoenix automobiles.

Each OEM Pontiac Phoenix Coolant Temperature Sensor we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Pontiac Phoenix Coolant Temperature Sensor Parts Questions & Experts Answers

Sensor Asm,Engine Coolant Temperature Gage
10045847
Q: When and how to replace the Coolant Temperature Sensor for Buick Skylark,Oldsmobile Omega and Pontiac Phoenix?
A: The coolant temperature indicator system includes an instrument panel lamp and a coolant temperature sensor or sender, situated at the left rear of the cylinder head on L4 engines, and at the rear of the right head on V6 engines. In place of a temperature sensor, the transducer replaces it if a temperature gauge is used on the instrument cluster. Where there is unusual indication or fault development, check first the coolant level in the system and then ensure that connecting wiring between gauge and sender unit is secure. When turning the ignition switch to the ON position with the starter motor turning, the indicator lamp should be illuminated (Overheated engine indication). The lamp may not be lit if; the bulb is burned out, the ignition switch is faulty or the circuit is open. Once the engine starts, the lamp should go out and remain so unless it overheats. The lamp may fail to go out because of a defective temperature sender unit or a faulty ignition switch or grounded wiring between the lamp and the sender unit. If you were going to change this Sensor unit, it would simply be unscrewed from the cylinder head after which another one could be installed in its place. There will be some loss of coolant so check levels after replacement has been installed.