How to replace a headlight for Oldsmobile Cutlass?

Whenever replacing the headlight, avoid turning the spring-loaded adjusting screws. Start by removing the headlight bezel screws and the decorative bezel. If applicable, use a cotter pin removal tool to unhook the spring from the retaining ring. Then, remove the retaining ring screws and withdraw the ring while supporting the light. Slightly pull the headlight unit outward and disconnect the electrical connector from the rear of the light. Remove the old light from the vehicle. Position the new unit close enough to connect the electrical connector, ensuring that the numbers molded into the lens are at the top. Install the retaining ring with its mounting screws and spring. Finally, install the decorative bezel and check for proper operation. Remember to adjust the headlight aim after installing a new headlight.

How to adjust the Headlight and remove the lighting switch?

Adjustment screws are provided at the front of the lamp to alter the lamp beam in both the horizontal and vertical planes. It is strongly recommended that this work is left to a service station having modern beam setting equipment, any adjustment at home being regarded as a temporary, emergency operation. With the headlights in the 'full on' position, reach up under the dashboard and depress the lighting switch shaft retainer while pulling gently on the lighting knob. Remove the shaft and knob assembly. Remove the nut which secures the-lighting switch to the carrier. For better access to the switch, remove the screws which secure the instrument cluster carrier and tilt the cluster. Unplug the electrical connector at the switch and remove the switch. Installation Is a reversal of removal. however, make sure that all ground connections are refastened and that the switch shaft is fully seated in the switch. The shaft retainer should lock the shaft into place. Disconnect the negative battery cable. Remove the cluster pad assembly. Remove the retaining screws and pull away the switch.

Genuine Oldsmobile Cutlass Headlight

Headlamp

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

27 Headlights found

View related parts
Oldsmobile Cutlass Headlight Capsule
Part Number: 5973931
$179.66 MSRP: $269.82
You Save: $90.16 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Capsule,Headlamp; Headlamp Assembly, Headlamp Capsule
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, CUTLASS CALAIS, CUTLASS CRUISER, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, STATION WAGON | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Oldsmobile Cutlass Headlamp Assembly, (W/ Parking & Turn Signal Lamp)
Part Number: 16524845
$79.18 MSRP: $151.68
You Save: $72.50 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Headlamp Assembly, (W/ Parking & Turn Signal Lamp) ; Headlamp Assembly, (W/ Park & T/Sig Lp); Composite Assembly, Headlamp Assembly
- Replaces: 16513401, 16519989
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Oldsmobile Cutlass | 2 DOOR, 4 DOOR | 6 Cyl 3.1L
View related parts
Oldsmobile Cutlass Headlamp Capsule Assembly, (Thin Wall)/Lh
Part Number: 5973932
$130.15 MSRP: $187.04
You Save: $56.89 (31%)
ADD TO CART
Product Specifications
- Other Name: Headlamp Assembly, Headlamp Capsule
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, CUTLASS CALAIS, CUTLASS CRUISER, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, STATION WAGON | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Oldsmobile Cutlass Headlamp Capsule Assembly
Part Number: 16505636
$180.20
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Capsule Assembly, Headlamp ; Capsule Assembly, Hdlp; Headlamp Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1990 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, SL 2 DOOR, SL 4 DOOR, SL STATION WAGON, STATION WAGON | 4 Cyl 2.3L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Oldsmobile Cutlass Capsule/Headlamp/Fog Lamp Headlamp
Part Number: 22618781
Product Specifications
- Other Name: Headlamp Asm ; Headlamp, Capsule/Headlamp/Fog Lamp; Composite Headlamp, Headlamp Assembly
- Replaces: 22604268, 22611382
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Oldsmobile Cutlass | SEDAN LEVEL I, SEDAN LEVEL II | 6 Cyl 3.1L
View related parts
Oldsmobile Cutlass Headlamp Capsule Assembly
Part Number: 16510744
Product Specifications
- Other Name: Capsule Assembly, Headlamp ; Capsule, Capsule/Headlamp/Fog Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1997 Oldsmobile Cutlass | 2 DOOR, INTERNAL 2 DOOR | 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.4L
View related parts
Oldsmobile Cutlass Capsule/Headlamp/Fog Lamp Headlamp
Part Number: 22618782
Product Specifications
- Other Name: Headlamp Asm ; Headlamp, Capsule/Headlamp/Fog Lamp; Composite Headlamp, Headlamp Assembly
- Replaces: 22611383
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Oldsmobile Cutlass | SEDAN LEVEL I, SEDAN LEVEL II | 6 Cyl 3.1L
View related parts
Oldsmobile Cutlass Headlight Assembly
Part Number: 16513310
Product Specifications
- Other Name: Headlamp Asm ; Capsule, Capsule/Headlamp/Fog Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1997 Oldsmobile Cutlass | 2 DOOR, INTERNAL 2 DOOR | 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.4L
View related parts
Oldsmobile Cutlass Headlight Capsule(Low Beam)
Part Number: 15194306
Product Specifications
- Other Name: Capsule,Headlamp(Low Beam) ; Capsule, Capsule/Headlamp/Fog Lamp; Headlamp Assembly, Headlamp Capsule
- Replaces: 5973929, 05973929
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, CUTLASS CALAIS, CUTLASS CRUISER, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, STATION WAGON | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Oldsmobile Cutlass Headlight Capsule(Low Beam)
Part Number: 15194307
Product Specifications
- Other Name: Capsule,Headlamp(Low Beam) ; Capsule, Capsule/Headlamp/Fog Lamp; Headlamp Assembly, Headlamp Capsule
- Replaces: 5973930, 05973930
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, CUTLASS CALAIS, CUTLASS CRUISER, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, STATION WAGON | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Oldsmobile Cutlass Head Left Lamp Assembly
Part Number: 16501995
Product Specifications
- Other Name: Lamp Assembly, Head Lh ; Capsule, Headlamp; Headlamp Assembly, Headlamp Capsule, Sealed Beam
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, CUTLASS CALAIS, CUTLASS CRUISER, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, STATION WAGON | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Oldsmobile Cutlass Head Right Lamp Assembly
Part Number: 16501996
Product Specifications
- Other Name: Lamp Assembly, Head Rh ; Capsule, Headlamp; Headlamp Assembly, Headlamp Capsule, Sealed Beam
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, CUTLASS CALAIS, CUTLASS CRUISER, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, STATION WAGON | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Oldsmobile Cutlass Capsule/Headlamp/Fog Lamp Headlamp
Part Number: 16520984
Product Specifications
- Other Name: Headlamp Asm ; Headlamp, Capsule/Headlamp/Fog Lamp; Composite Assembly, Headlamp Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1997 Oldsmobile Cutlass | 4 DOOR, INTERNAL 4 DOOR | 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.4L
View related parts
Oldsmobile Cutlass Capsule/Headlamp/Fog Lamp Headlamp
Part Number: 16520983
Product Specifications
- Other Name: Headlamp Asm ; Headlamp, Capsule/Headlamp/Fog Lamp; Composite Assembly, Headlamp Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1997 Oldsmobile Cutlass | 4 DOOR, INTERNAL 4 DOOR | 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.4L
View related parts
Oldsmobile Cutlass Headlamp Assembly, (W/ Parking & Turn Signal Lamp)
Part Number: 16524846
Product Specifications
- Other Name: Composite Assembly, Headlamp Assembly
- Replaces: 16513402, 16519990
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Oldsmobile Cutlass | 2 DOOR, 4 DOOR | 6 Cyl 3.1L
View related parts
Oldsmobile Cutlass Headlamp Capsule Assembly
Part Number: 16520813
Product Specifications
- Other Name: Capsule Assembly, Headlamp ; Capsule, Capsule/Headlamp/Fog Lamp; Headlamp Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, S 2 DOOR, S 4 DOOR, S STATION WAGON, SL 2 DOOR, SL 4 DOOR, SL STATION WAGON, STATION WAGON | 4 Cyl 2.2L, 4 Cyl 2.3L, 4 Cyl 2.5L, 6 Cyl 3.1L, 6 Cyl 3.3L
View related parts
Oldsmobile Cutlass Headlamp Assembly
Part Number: 16510743
Product Specifications
- Other Name: Headlamp Asm ; Capsule A; Composite Assembly, Composite Headlamp, Headlamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1997 Oldsmobile Cutlass | 2 DOOR, INTERNAL 2 DOOR | 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.4L
View related parts
Oldsmobile Cutlass Headlamp Assembly
Part Number: 16514626
Product Specifications
- Other Name: Headlamp Asm; Composite Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Oldsmobile Cutlass | 4 DOOR, INTERNAL 4 DOOR | 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.4L
View related parts
Oldsmobile Cutlass Headlight Assembly
Part Number: 16511775
Product Specifications
- Other Name: Headlamp Asm; Composite Assembly, Headlamp Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Oldsmobile Cutlass | 2 DOOR, 4 DOOR | 4 Cyl 2.3L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.4L
View related parts
Oldsmobile Cutlass Headlamp Assembly
Part Number: 16511776
Product Specifications
- Other Name: Headlamp Asm; Composite Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Oldsmobile Cutlass | 2 DOOR, 4 DOOR | 4 Cyl 2.3L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.4L

| Page 1 of 2 |Next >

1-20 of 27 Results

Oldsmobile Cutlass Headlight Parts Questions & Experts Answers

Headlight Capsule(Low Beam)
15194306
Q: How to replace a headlight for Oldsmobile Cutlass?
A: Whenever replacing the headlight, avoid turning the spring-loaded adjusting screws. Start by removing the headlight bezel screws and the decorative bezel. If applicable, use a cotter pin removal tool to unhook the spring from the retaining ring. Then, remove the retaining ring screws and withdraw the ring while supporting the light. Slightly pull the headlight unit outward and disconnect the electrical connector from the rear of the light. Remove the old light from the vehicle. Position the new unit close enough to connect the electrical connector, ensuring that the numbers molded into the lens are at the top. Install the retaining ring with its mounting screws and spring. Finally, install the decorative bezel and check for proper operation. Remember to adjust the headlight aim after installing a new headlight.
Headlight Capsule
5973931
Q: How to adjust the Headlight and remove the lighting switch?
A: Adjustment screws are provided at the front of the lamp to alter the lamp beam in both the horizontal and vertical planes. It is strongly recommended that this work is left to a service station having modern beam setting equipment, any adjustment at home being regarded as a temporary, emergency operation. With the headlights in the 'full on' position, reach up under the dashboard and depress the lighting switch shaft retainer while pulling gently on the lighting knob. Remove the shaft and knob assembly. Remove the nut which secures the-lighting switch to the carrier. For better access to the switch, remove the screws which secure the instrument cluster carrier and tilt the cluster. Unplug the electrical connector at the switch and remove the switch. Installation Is a reversal of removal. however, make sure that all ground connections are refastened and that the switch shaft is fully seated in the switch. The shaft retainer should lock the shaft into place. Disconnect the negative battery cable. Remove the cluster pad assembly. Remove the retaining screws and pull away the switch.