How do you remove and install the Slave Cylinder on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

To disconnect the retainer clip from the clutch slave cylinder pushrod, ensuring the Clutch Slave Cylinder is not damaged when the clutch pedal is depressed, start by raising the vehicle and securely supporting it on jackstands. For 1994 and 1995 models, disconnect the hydraulic line from the Clutch Slave Cylinder by removing the cotter pin and pulling the line straight off its fitting. Then, remove the two Clutch Slave Cylinder mounting nuts and detach the Clutch Slave Cylinder. Install the Clutch Slave Cylinder on the clutch housing, ensuring the pushrod is seated in the release lever pocket. Connect the hydraulic line to the Clutch Slave Cylinder and secure it with a new cotter pin. For 1996 and later models, removal involves removing the transmission and the two Clutch Slave Cylinder retaining bolts. Slide the Clutch Slave Cylinder off the transmission input shaft and inspect the clutch disc and pressure plate assembly while the transmission is removed. Replace as necessary. Clean off the transmission input shaft and coat it with multi-purpose grease. Slide the new Clutch Slave Cylinder onto the input shaft, install the retaining bolts, and tighten them to the specified torque. Finally, install the transmission, fill the clutch fluid reservoir with the recommended fluid, bleed the clutch hydraulic system, and lower the vehicle by removing the jackstands.

Genuine GMC Sonoma Clutch Slave Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Clutch Slave Cylinders found

View related parts
GMC Sonoma Cylinder Asm,Clutch Actuator
Part Number: 24264182
$168.34 MSRP: $266.08
You Save: $97.74 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Clutch Hydraulic Release Slave/Actuator; Slave Cylinder
- Replaces: 15018532, 15727249, 15998501, 12565145, 15046288, 15742944
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2001 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
GMC Sonoma Cylinder Assembly, Clutch Actuator
Part Number: 20958083
$184.75 MSRP: $292.00
You Save: $107.25 (37%)
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Clutch Hydraulic Release Slave/Actuator; Slave Cylinder
- Replaced by: 19432064
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2004 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
GMC Sonoma Cylinder,Clutch Actuator
Part Number: 15679690
$108.59 MSRP: $170.86
You Save: $62.27 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Clutch Hydraulic Release Slave/Actuator; Slave Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 GMC Sonoma | PICKUP | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Cylinder Asm,Clutch Actuator
Part Number: 12387940
Product Specifications
- Other Name: CYLINDER, Clutch Hydraulic Release Slave/Actuator; Slave Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 6 Cyl 4.3L
View related parts
GMC Sonoma Cylinder Asm,Clutch Actuator
Part Number: 15580493
Product Specifications
- Other Name: CYLINDER, Clutch Hydraulic Release Slave/Actuator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 GMC Sonoma | PICKUP | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Cylinder Assembly, Clutch Slave
Part Number: 15534378
Product Specifications
- Other Name: CYLINDER, Clutch Hydraulic Release Slave/Actuator; Slave Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 GMC Sonoma | PICKUP | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L

GMC Sonoma Clutch Slave Cylinder

The Clutch Slave Cylinder is an essential part of the GMC Sonama, manual transmission systems used in the car's engine; together with the clutch master cylinder it helps to disengage the clutch every time the pedal is pressed. This hydraulic part transmits the force of the driver into hydraulic pressure to protrude a particular rod that gets in touch to a lever or fork to effect safe shifting of gears. In the past GMC Sonoma cars have used hydraulic clutch slave cylinders which are widely considered more effective than mechanical rods. Misfires of the clutch slave cylinder can result to poor feel of the pedals, poor shifting of the gears and may even damage the transmission system hence making any service or repair necessary for proper drivability of the car.

Each OEM GMC Sonoma Clutch Slave Cylinder we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Sonoma Clutch Slave Cylinder Parts Questions & Experts Answers

Cylinder Asm,Clutch Actuator
24264182
Q: How do you remove and install the Slave Cylinder on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: To disconnect the retainer clip from the clutch slave cylinder pushrod, ensuring the Clutch Slave Cylinder is not damaged when the clutch pedal is depressed, start by raising the vehicle and securely supporting it on jackstands. For 1994 and 1995 models, disconnect the hydraulic line from the Clutch Slave Cylinder by removing the cotter pin and pulling the line straight off its fitting. Then, remove the two Clutch Slave Cylinder mounting nuts and detach the Clutch Slave Cylinder. Install the Clutch Slave Cylinder on the clutch housing, ensuring the pushrod is seated in the release lever pocket. Connect the hydraulic line to the Clutch Slave Cylinder and secure it with a new cotter pin. For 1996 and later models, removal involves removing the transmission and the two Clutch Slave Cylinder retaining bolts. Slide the Clutch Slave Cylinder off the transmission input shaft and inspect the Clutch Disc and Pressure Plate assembly while the transmission is removed. Replace as necessary. Clean off the transmission input shaft and coat it with multi-purpose grease. Slide the new Clutch Slave Cylinder onto the input shaft, install the retaining bolts, and tighten them to the specified torque. Finally, install the transmission, fill the clutch fluid reservoir with the recommended fluid, bleed the clutch hydraulic system, and lower the vehicle by removing the jackstands.