How do you disconnect the brake pedal position sensor on Chevrolet Express and GMC Savana?

Disconnect the negative battery terminal. Next, disconnect the electrical connector to the brake light switch. Proceed to remove the bolt securing the brake light switch to the brake pedal, then remove the Brake Light Switch. For installation, install the Brake Light Switch, then install the mounting bolt and tighten it to the proper torque specifications. Finally, have the Brake Light Switch calibrated.

How to Troubleshoot and Replace the Brake Light Switch on Chevrolet Express and GMC Savana?

The brake light switch is located on the side and activates the brake lights when the pedal is depressed. If there is voltage, check for power at the brake light wires at the tail light housings. If there is no power, repair the circuit between the switch and the brake lights. If there is power, check for bad ground using a jumper wire connected to a good ground. To replace the switch, remove the left side under the dash panel and the heater/air conditioning duct. Unplug the electrical connector from the switch and remove the clip that retains the switch and pushrod to the pin on the brake pedal arm. Slip the brake light switch off the pin and install the new switch by reversing the removal procedure.

Genuine GMC Savana Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Brake Light Switches found

View related parts
GMC Savana Switch Assembly, Stop Lamp
Part Number: 15861245
$21.55 MSRP: $40.66
You Save: $19.11 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SWITCH, Stop Lamp Switch; Stoplamp Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2011 GMC Savana | 1 TON CARGO EXPRESS, 1 TON CARGO SAVANA, 1 TON COMMERCIAL/RV CUTAWAY, 1 TON PASSENGER, 1/2 TON CARGO EXPRESS, 1/2 TON CARGO SAVANA, 1/2 TON PASSENGER EXPRESS, 1/2 TON PASSENGER SAVANA, 3/4 TON CARGO EXPRESS, 3/4 TON CARGO SAVANA, 3/4 TON PASSENGER EXPRESS, 3/4 TON PASSENGER SAVANA | 6 Cyl 4.3L, 8 Cyl 4.8L, 8 Cyl 4.8L Flex, 8 Cyl 5.3L, 8 Cyl 6.0L, 8 Cyl 6.0L Flex, 8 Cyl 6.6L Diesel
View related parts
GMC Savana Sensor Assembly, Brake Pedal Position
Part Number: 13597415
$7.16 MSRP: $13.50
You Save: $6.34 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Brake; Brake Switch, Position Sensor, Stoplamp Switch
- Replaces: 22865566
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2024 GMC Savana | 1 TON CARGO SAVANA, 1 TON COMMERCIAL/RV CUTAWAY, 1 TON PASSENGER, 1/2 TON CARGO SAVANA, 1/2 TON PASSENGER SAVANA, 3/4 TON CARGO SAVANA, 3/4 TON PASSENGER SAVANA | 4 Cyl 2.8L Diesel, 6 Cyl 4.3L, 8 Cyl 4.8L Flex, 8 Cyl 5.3L, 8 Cyl 6.0L, 8 Cyl 6.0L Flex, 8 Cyl 6.6L, 8 Cyl 6.6L Diesel
View related parts
GMC Savana Sensor Assembly, Brake Pedal Position
Part Number: 13579088
$13.11 MSRP: $24.74
You Save: $11.63 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Brake; Stoplamp Switch
- Replaces: 22774281
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012 GMC Savana | 1 TON CARGO SAVANA, 1 TON COMMERCIAL/RV CUTAWAY, 1 TON PASSENGER, 1/2 TON CARGO SAVANA, 1/2 TON PASSENGER SAVANA, 3/4 TON CARGO SAVANA, 3/4 TON PASSENGER SAVANA | 6 Cyl 4.3L, 8 Cyl 4.8L Flex, 8 Cyl 5.3L, 8 Cyl 6.0L, 8 Cyl 6.0L Flex, 8 Cyl 6.6L Diesel
View related parts
GMC Savana Switch,Stop Lamp
Part Number: 15128874
$34.36 MSRP: $64.40
You Save: $30.04 (47%)
ADD TO CART
Product Specifications
- Other Name: SWITCH, Stop Lamp Switch; Stoplamp Switch
- Replaces: 15163032, 15038393, 25771554, 15161650, 15158767
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2007 GMC Savana | 1 TON CARGO SAVANA, 1 TON COMMERCIAL/RV CUTAWAY, 1 TON PASSENGER, 1/2 TON CARGO SAVANA, 1/2 TON PASSENGER SAVANA, 3/4 TON CARGO SAVANA, 3/4 TON PASSENGER SAVANA | 6 Cyl 4.3L, 8 Cyl 4.8L, 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 6.0L, 8 Cyl 6.6L Diesel
View related parts
GMC Savana Switch Assembly, Stop Lamp
Part Number: 93801733
Product Specifications
- Other Name: SWITCH, Stop Lamp Switch; Stoplamp Switch
- Replaces: 93441581, 11516282
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 GMC Savana | 1 TON CARGO EXPRESS, 1 TON CARGO SAVANA, 1 TON COMMERCIAL/RECREATIONAL VEHICLE EXPRESS, 1 TON COMMERCIAL/RECREATIONAL VEHICLE SAVANA, 1 TON PASSENGER, 1/2 TON CARGO, 1/2 TON CARGO EXPRESS, 1/2 TON CARGO SAVANA, 1/2 TON PASSENGER EXPRESS, 1/2 TON PASSENGER SAVANA, 3/4 TON CARGO EXPRESS, 3/4 TON CARGO SAVANA, 3/4 TON PASSENGER EXPRESS, 3/4 TON PASSENGER SAVANA | 6 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.5L Diesel, 8 Cyl 7.4L, 8 Cyl 8.1L

GMC Savana Brake Light Switch

Each OEM GMC Savana Brake Light Switch we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Savana Brake Light Switch Parts Questions & Experts Answers

Sensor Assembly, Brake Pedal Position
13597415
Q: How do you disconnect the brake pedal position sensor on Chevrolet Express and GMC Savana?
A: Disconnect the negative battery terminal. Next, disconnect the electrical connector to the brake light switch. Proceed to remove the bolt securing the brake light switch to the brake pedal, then remove the Brake Light Switch. For installation, install the Brake Light Switch, then install the mounting bolt and tighten it to the proper torque specifications. Finally, have the Brake Light Switch calibrated.
Sensor Assembly, Brake Pedal Position
13579088
Q: How to Troubleshoot and Replace the Brake Light Switch on Chevrolet Express and GMC Savana?
A: The brake light switch is located on the side and activates the brake lights when the pedal is depressed. If there is voltage, check for power at the brake light wires at the tail light housings. If there is no power, repair the circuit between the switch and the brake lights. If there is power, check for bad ground using a jumper wire connected to a good ground. To replace the switch, remove the left side under the dash panel and the heater/air conditioning duct. Unplug the electrical connector from the switch and remove the clip that retains the switch and pushrod to the pin on the brake pedal arm. Slip the brake light switch off the pin and install the new switch by reversing the removal procedure.