How to remove and install the oil pump on 2.2L four cylinder engine on GMC Jimmy?

The oil pan is taken off first before removing and installing the oil pump. Take out the oil pump mounting bolt from the main bearing cap after that. The block should be separated from the oil pump and pick-up assembly. If there is a problem with the latter, replace it with a new one. When doing a complete engine overhaul, it is advisable to use a new oil pump rather than reusing the old one or rebuilding it. The oil pickup tube of an oil pump should be checked for any looseness if it's pressed into the body of the oil pump. It's dangerous to attempt tightening a loose one; instead, replace the entire pump assembly. Put the oil pump in place by turning its shaft to align tang of gear with slot on lower end of oil pump drive shaft. The retainer on lower side of the oil pump drive shaft will enable easy movement of the entire thing over to its position. If not, remove it twisting tang until properly aligned with driveshaft slot in pump. Tighten up this mount using its bolt you earlier detached. Put back your vehicle's engine and start placing some engine before checking if there are any leaks.

How to remove the oil pan and oil pump on 4.3L V6 engine on GMC Jimmy?

Remove the oil pan. While supporting the oil pump, remove the pump-to-rear main bearing cap bolt. On some models, the oil pan baffle must be removed first, since it's also held in place by the pump mounting bolt. Lower the pump and remove it along with the pump driveshaft. If a new oil pump is installed, make sure the pump driveshaft is mated with the shaft inside the pump. Position the pump on the engine and make sure the slot in the upper end of the driveshaft is aligned with the tang on the lower end of the distributor shaft. The distributor drives the oil pump, so it is absolutely essential that the components mate properly. Install the mounting bolt and tighten it. Install the oil pan and refill with fresh oil. The remainder of assembly is the reverse of the disassembly procedures.

Genuine GMC Jimmy Oil Pump

Oil Fluid Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Oil Pumps found

View related parts
GMC Jimmy Pump,Oil
Part Number: 93442037
$153.96 MSRP: $267.94
You Save: $113.98 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PUMP, Engine Oil Pump; Oil Pump
- Replaces: 12555283
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Pump Asm,Oil (W/ Screen)
Part Number: 19210599
$199.52 MSRP: $315.34
You Save: $115.82 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: PUMP, Engine Oil Pump; Oil Pump
- Replaces: 12555167, 19170290
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1991 GMC Jimmy | 1/2 TON
View related parts
GMC Jimmy Pump,Oil
Part Number: 93427692
$127.62 MSRP: $201.71
You Save: $74.09 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: PUMP, Engine Oil Pump; Oil Pump, Pump Assembly
- Replaces: 12555884, 03848907, 3848907, 12555284
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1993 GMC Jimmy | 1/2 TON, 2 DOOR, 4 DOOR | 6 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
GMC Jimmy Pump Asm,Oil
Part Number: 12366006
$65.23 MSRP: $131.54
You Save: $66.31 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PUMP, Engine Oil Pump; Oil Pump
- Replaces: 10008202, 10008206
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 GMC Jimmy | 2 DOOR, 4 DOOR
View related parts
GMC Jimmy Pump, Oil
Part Number: 14091485
$138.58 MSRP: $219.02
You Save: $80.44 (37%)
ADD TO CART
Product Specifications
- Other Name: PUMP, Engine Oil Pump; Oil Pump
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1989 GMC Jimmy | 1/2 TON
View related parts
GMC Jimmy Drive Asm, Oil Pump & Sensor (Includes Revolutions Per Minute Speed Sensor)
Part Number: 7849305
Product Specifications
- Other Name: DRIVE, Engine Oil Pump
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 GMC Jimmy | 1/2 TON | 8 Cyl 6.2L Diesel
View related parts
GMC Jimmy Pump Assembly, Oil
Part Number: 10118640
Product Specifications
- Other Name: PUMP, Engine Oil Pump; Oil Pump
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 GMC Jimmy | 2 DOOR, 4 DOOR
View related parts
GMC Jimmy Pump Assembly, Oil
Part Number: 10183985
Product Specifications
- Other Name: PUMP, Engine Oil Pump; Oil Pump
- Replaces: 88893902
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1991 GMC Jimmy | 1/2 TON | 8 Cyl 6.2L Diesel
View related parts
GMC Jimmy Body Kit,Automatic Transmission Fluid Pump
Part Number: 24230108
Product Specifications
- Other Name: BODY, Transmission Oil Pump
- Replaces: 08649964, 8649964
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
- 1997-1999 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
- 1985-1991 GMC Jimmy | 1/2 TON | 6 Cyl 2.8L, 6 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L Diesel
View More
View related parts
GMC Jimmy Body,Pump(Remanufacture)
Part Number: 8679988
Product Specifications
- Other Name: BODY, Transmission Oil Pump
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1990 GMC Jimmy | 1/2 TON | 6 Cyl 2.8L, 6 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L Diesel

GMC Jimmy Oil Pump

The Oil Pump within GE'S GMC Jimmy automobiles is a vital component for the continuous flow of oil in the internal combustion engine under high pressure to adequately lubricate and cool parts of the engine. It has the gears, springs, sealants or gasket and provides lubricant to such parts as the bearings or the pistons. GMC Jimmy vehicles use several types of oil pumps; the gear, trochoid, and vane pumps adopting mechanical pumps because of their efficiency in being driven by the crankshaft or camshaft. Sustaining a proper pressure of the oil, preferably 10 psi for every 1000 RPM, is crucial since too much and too little pressure can be dangerous to the engines. Since engines in different models of GMC Jimmy are high performance it could be that newer and more complex lubrication systems are incorporated such as the dry sump systems with multiple pumps for oil circulation and pressure. Maintenance such as changing engine oil and its filter is also mandatory in order to avoid formation of blockage to the system, for effectiveness and durability of an engine that is used in a vehicle.

Each OEM GMC Jimmy Oil Pump we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Jimmy Oil Pump Parts Questions & Experts Answers

Pump,Oil
93442037
Q: How to remove and install the oil pump on 2.2L four cylinder engine on GMC Jimmy?
A: The Oil Pan is taken off first before removing and installing the oil pump. Take out the oil pump mounting bolt from the main bearing cap after that. The block should be separated from the oil pump and pick-up assembly. If there is a problem with the latter, replace it with a new one. When doing a complete engine overhaul, it is advisable to use a new oil pump rather than reusing the old one or rebuilding it. The oil pickup tube of an oil pump should be checked for any looseness if it's pressed into the body of the oil pump. It's dangerous to attempt tightening a loose one; instead, replace the entire pump assembly. Put the oil pump in place by turning its shaft to align tang of gear with slot on lower end of oil pump drive shaft. The retainer on lower side of the oil pump drive shaft will enable easy movement of the entire thing over to its position. If not, remove it twisting tang until properly aligned with driveshaft slot in pump. Tighten up this mount using its bolt you earlier detached. Put back your vehicle's engine and start placing some engine before checking if there are any leaks.
Pump,Oil
93442037
Q: How to remove the oil pan and oil pump on 4.3L V6 engine on GMC Jimmy?
A: Remove the Oil Pan. While supporting the oil pump, remove the pump-to-rear main bearing cap bolt. On some models, the oil pan baffle must be removed first, since it's also held in place by the pump mounting bolt. Lower the pump and remove it along with the pump driveshaft. If a new oil pump is installed, make sure the pump driveshaft is mated with the shaft inside the pump. Position the pump on the engine and make sure the slot in the upper end of the driveshaft is aligned with the tang on the lower end of the distributor shaft. The distributor drives the oil pump, so it is absolutely essential that the components mate properly. Install the mounting bolt and tighten it. Install the oil pan and refill with fresh oil. The remainder of assembly is the reverse of the disassembly procedures.