How to remove and install steering rack boots on Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

To remove and install rack and pinion boots, loosen the wheel lug nuts, raise the front of the vehicle, and support it securely on jackstands. Remove the tie-rod ends and the locknuts. Remove the outer boot clamps with pliers, cut off the inner boot clamps, and throw them away. Mark the location of the breather tube in relation to the rack and pinion assembly, then remove the boots and the tube. Apply grease to the exposed ends of the toothed rack before installing new boots. To install new boots, install a new clamp on the inner end of the boot. Apply grease to the groove on the tie-rod and the mounting grooves on the rack and pinion. Line up the breather tube with the marks made during removal (if applicable) and slide the new boot onto the rack and pinion housing. Make sure the boot isn't twisted, then tighten the new inner clamp. Install the outer clamps and tie-rod end locknuts. Finally, install the tie-rod ends and have the front-end alignment checked and, if necessary, adjusted.

Genuine Chevrolet Tahoe Rack and Pinion Boot

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Rack and Pinion Boots found

View related parts
Chevrolet Tahoe Boot Kit,Steering Gear
Part Number: 15254057
$41.17 MSRP: $71.68
You Save: $30.51 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: BOOT KIT, Tie Rod End Dust; Boot Kit, Tie Rod Boot
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 4.8L, 8 Cyl 5.3L, 8 Cyl 5.3L Flex
View related parts
Chevrolet Tahoe Boot Kit, Steering Gear
Part Number: 22834081
$34.98 MSRP: $57.89
You Save: $22.91 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: BOOT KIT, Tie Rod End Dust; Boot Kit, Tie Rod Boot
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2021 Chevrolet Tahoe | 1500 4 DOOR UTILITY, 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Boot Kit, Steering Gear
Part Number: 15895648
$67.98 MSRP: $108.44
You Save: $40.46 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: BOOT KIT, Tie Rod End Dust; Boot Kit, Tie Rod Boot
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2013 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 6.0L, 8 Cyl 6.0L Flex
View related parts
Chevrolet Tahoe Boot,Steering Gear (Spool Shaft)
Part Number: 26048003
Product Specifications
- Other Name: SEAL, Steering Gear Hydraulic Valve; Dust Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 4.8L, 8 Cyl 5.3L, 8 Cyl 5.3L Flex

Chevrolet Tahoe Rack and Pinion Boot

The Rack and Pinion Boot that is used in Chevrolet Tahoe vehicles is an important rubber parts that act as a cover for the steering rack hence protecting it from dust and other unwanted substances that may wear out the rack and pinion system. Hence, the boot creates a seal at each end of the rack and plays the important aspect of avoiding any possible risk of failure. One should consider carrying out some checks and maintenance procedures on the Rack and Pinion Boot to prevent complications that could be as a result of the cracks or harm to the Rack and Pinion Boot.

Each OEM Chevrolet Tahoe Rack and Pinion Boot we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Tahoe Rack and Pinion Boot Parts Questions & Experts Answers

Boot Kit,Steering Gear
15254057
Q: How to remove and install steering rack boots on Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?
A: To remove and install rack and pinion boots, loosen the wheel lug nuts, raise the front of the vehicle, and support it securely on jackstands. Remove the tie-rod ends and the locknuts. Remove the outer boot clamps with pliers, cut off the inner boot clamps, and throw them away. Mark the location of the breather tube in relation to the rack and pinion assembly, then remove the boots and the tube. Apply grease to the exposed ends of the toothed rack before installing new boots. To install new boots, install a new clamp on the inner end of the boot. Apply grease to the groove on the tie-rod and the mounting grooves on the rack and pinion. Line up the breather tube with the marks made during removal (if applicable) and slide the new boot onto the rack and pinion housing. Make sure the boot isn't twisted, then tighten the new inner clamp. Install the outer clamps and tie-rod end locknuts. Finally, install the tie-rod ends and have the front-end alignment checked and, if necessary, adjusted.