How to remove and install an oil pan on 4.3L V6 Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

Disconnect the cable from the negative terminal of the battery. Raise the vehicle and support it securely on jackstands, drain the engine oil, and remove the oil filter. Remove the oil pan skid plate if equipped. Remove the lower crossmember from below the oil pan. On 4WD models, remove the front differential carrier. There is an engine wiring harness at the front of the oil pan. Disconnect the harness bracket. Disconnect the front exhaust Y pipe from the engine and the exhaust system and remove it from the vehicle. Remove the starter motor. Also, remove the plastic bell housing side covers. Disconnect the transmission cooler line bracket from the side of the oil pan. Disconnect the remaining wiring harness brackets. Remove the transmission-to-engine mounting bolts. Disconnect the electrical connector from the oil level sensor if equipped. Remove the transmission-to-oil pan bolts. Remove the oil pan bolts, then lower the pan from the engine. The pan will probably stick to the engine, so strike the pan with a rubber mallet until it breaks the gasket seal. Wash out the oil pan with solvent. Thoroughly clean the mounting surfaces of the oil pan and engine block of old gasket material and sealer. Wipe the gasket surfaces clean with a rag soaked in brake system cleaner. Apply a 3/16-inch wide, one-inch long bead of ATV sealant to the corners where the front cover meets the block and at the rear where the rear main cap meets the block. Then attach the new gasket to the pan, install the pan, and tighten the bolts/studs finger-light. The alignment of the rear face of the aluminum pan to the rear of the block is important. Measure between the rear face of the pan and the front face of the transmission bell housing with feeler gauges. Clearance should ideally be flush, but up to 0.011 inches is allowable. If the clearance is OK, tighten the pan bolts/studs in sequence to the torque specifications. The remainder of installation is the reverse of removal. Add the proper type and quantity of oil, start the engine, and check for leaks before placing the vehicle back in service.

How to remove and replace the oil pan on V8 Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

Disconnect the cable from the negative terminal of the battery. Raise the vehicle and support it securely on jackstands, drain the engine oil, and remove the oil filler. Remove the oil pan skid plate, if equipped. Unbolt the steering rack and allow it to hang out of the way. On 4WD vehicles, remove the front differential carrier. Remove the transmission bell housing covers from the rear of the engine block. Remove the crossmember. Remove the lower transmission-to-engine bolt(s). These bolts vary depending on the model of transmission used but all screw into the oil pan. Disconnect the wiring from the engine oil level sensor. Disconnect the wiring harness retainers from the oil pan. Disconnect the oil cooler lines from the oil pan on models with automatic transmissions. Remove all the oil pan bolts, then lower the pan from the engine. The pan will probably stick to the engine, so strike the pan with a rubber mallet until it breaks the gasket seal. Drill out the rivets securing the oil pan gasket to the oil pan and remove the old gasket. Wash out the oil pan with solvent. Thoroughly clean the mounting surfaces of the oil pan and engine block of old gasket material and sealant. Wipe the gasket surfaces clean with a rag soaked in brake system cleaner. Apply a 3/16-inch wide, one-inch long bead of ATV sealant to the corners of the block where the front cover and the rear cover meet the engine block. The gasket tabs protrude at these points and must have sealant around them. Attach the new gasket to the pan, install the pan, and tighten the bolts finger-tight. Be sure the oil gallery passages in the pan and the gasket are aligned properly. Install all of the oil pan mounting bolts snugly. Install the lower transmission mounting bolts snugly. Tighten the oil pan bolts and the transmission bolts to the correct torque specifications. The remainder of installation is the reverse of removal. Add the proper type and quantity of oil, start the engine, and check for leaks before placing the vehicle back in service.

Genuine Chevrolet Suburban Oil Pan

Oil Drain Pan

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

30 Oil Pans found

View related parts
Chevrolet Suburban Pan, Lower Oil
Part Number: 12669909
$45.71 MSRP: $79.53
You Save: $33.82 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan, Lwr Oil; Lower Oil Pan, Oil Pan
- Position: Lower
- Replaces: 12659686, 12623115
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Suburban | 1500 4 DOOR UTILITY | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Suburban Pan Assembly, Oil
Part Number: 12640746
$210.11 MSRP: $365.72
You Save: $155.61 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Replaces: 12627903, 12619776
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2019 Chevrolet Suburban | 3500 4 DOOR UTILITY | 8 Cyl 6.0L Flex
- 2007-2014 Chevrolet Suburban | 1/2 TON, 3/4 TON | 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 6.0L, 8 Cyl 6.0L Flex
View related parts
Chevrolet Suburban Pan Assembly, Oil
Part Number: 12609074
$201.78 MSRP: $351.19
You Save: $149.41 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Replaces: 12594603
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Suburban | 1/2 TON, 3/4 TON | 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 6.0L
View related parts
Chevrolet Suburban Pan,Oil
Part Number: 12557558
$141.67 MSRP: $246.56
You Save: $104.89 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan, Oil Pan Gasket
- Replaces: 12528916
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1999 Chevrolet Suburban | 1/2 TON, 3/4 TON | 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Suburban Pan Kit,Oil(W/Gasket)
Part Number: 12528916
$141.67 MSRP: $246.56
You Save: $104.89 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil
- Replaced by: 12557558
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1991 Chevrolet Suburban | 1/2 TON, 3/4 TON | 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Suburban Pan Assembly, Oil
Part Number: 98073535
$216.50 MSRP: $243.92
You Save: $27.42 (12%)
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil; Lower Oil Pan, Oil Pan
- Replaces: 97329637, 97360794, 97220006
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chevrolet Suburban | 2500 CREW CAB LONG BOX, 2500 CREW CAB STANDARD BOX, 2500 EXTENDED CAB LONG BOX, 2500 EXTENDED CAB STANDARD BOX, 2500 REGULAR CAB, 3/4 TON, 3500 CHASSIS EXTENDED CAB 161.5, 3500 CHASSIS EXTENDED CAB 185.5, 3500 CHASSIS REGULAR CAB 137.0, 3500 CHASSIS REGULAR CAB 161.5, 3500 CREW CAB, 3500 EXTENDED CAB, 3500 REGULAR CAB, CLASSIC 2500 CREW CAB LONG BOX, CLASSIC 2500 CREW CAB STANDARD BOX, CLASSIC 2500 EXTENDED CAB LONG BOX, CLASSIC 2500 EXTENDED CAB STANDARD BOX, CLASSIC 2500 REGULAR CAB, CLASSIC 3500 CHASSIS EXTENDED CAB 161.5, CLASSIC 3500 CREW CAB, CLASSIC 3500 EXTENDED CAB, CLASSIC 3500 REGULAR CAB, EXT 3/4 TON, XL 3/4 TON
View related parts
Chevrolet Suburban Pan,Oil (W/Filt Bypass)
Part Number: 12579273
$303.22 MSRP: $527.73
You Save: $224.51 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Replaces: 12573695, 12560393
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 Chevrolet Suburban | 1/2 TON, 1500 CREW CAB, 1500 CREW CAB LONG BOX, 1500 CREW CAB STANDARD BOX, 1500 EXTENDED CAB LONG BOX, 1500 EXTENDED CAB STANDARD BOX, 1500 REGULAR CAB LONG BOX, 1500 REGULAR CAB STANDARD BOX, 2500 CREW CAB LONG BOX, 2500 CREW CAB STANDARD BOX, 2500 EXTENDED CAB LONG BOX, 2500 EXTENDED CAB STANDARD BOX, 2500 REGULAR CAB, 3/4 TON, 3500 CHASSIS EXTENDED CAB 161.5, 3500 CHASSIS EXTENDED CAB 185.5, 3500 CHASSIS REGULAR CAB 137.0, 3500 CHASSIS REGULAR CAB 161.5, 3500 CREW CAB, 3500 EXTENDED CAB, 3500 REGULAR CAB, 4 DOOR 1/2 TON, CLASSIC 1500 CREW CAB LONG BOX, CLASSIC 1500 EXTENDED CAB LONG BOX, CLASSIC 1500 EXTENDED CAB STANDARD BOX, CLASSIC 1500 REGULAR CAB LONG BOX, CLASSIC 1500 REGULAR CAB STANDARD BOX, CLASSIC 2500 CREW CAB LONG BOX, CLASSIC 2500 CREW CAB STANDARD BOX, CLASSIC 2500 EXTENDED CAB LONG BOX, CLASSIC 2500 EXTENDED CAB STANDARD BOX, CLASSIC 2500 REGULAR CAB, CLASSIC 3500 CHASSIS EXTENDED CAB 161.5, CLASSIC 3500 CREW CAB, CLASSIC 3500 EXTENDED CAB, CLASSIC 3500 REGULAR CAB, EXT 1/2 TON, EXT 3/4 TON, XL 1/2 TON, XL 3/4 TON, YUKON/DENALI | 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 6.0L
View related parts
Chevrolet Suburban PAN ASM-A/TRNS FLUID
Part Number: 24043538
$49.17 MSRP: $85.53
You Save: $36.36 (43%)
ADD TO CART
Product Specifications
- Other Name: Oil Pan, Transmission Pan
- Replaces: 24293671
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Suburban | 1/2 TON | 6 Cyl 3.0L Diesel, 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Suburban Pan Assembly, Oil
Part Number: 12684605
$220.79 MSRP: $348.96
You Save: $128.17 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pan, Upper Oil Pan
- Replaces: 12659685, 12619977, 12659831, 12666995, 12707241, 12668476
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Suburban | 1500 4 DOOR UTILITY | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Suburban Pan Assembly, Oil
Part Number: 12707243
$173.08 MSRP: $273.56
You Save: $100.48 (37%)
ADD TO CART
Product Specifications
- Other Name: Oil Pan
- Replaced by: 12732268
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Suburban | 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Suburban Pan Assembly, A/Trns Fluid
Part Number: 24045038
$37.78 MSRP: $65.72
You Save: $27.94 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pan, Transmission Pan
- Replaces: 24288996, 24274735, 24278775, 24291926, 24279518
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2022-2023 Chevrolet Suburban | 1/2 TON | 8 Cyl 5.3L
View related parts
Chevrolet Suburban Pan Assembly, Oil
Part Number: 12597153
$344.70 MSRP: $544.81
You Save: $200.11 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Replaces: 12558216
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004 Chevrolet Suburban | 1500 EXTENDED CAB LONG BOX, 1500 EXTENDED CAB STANDARD BOX, 1500 REGULAR CAB LONG BOX, 1500 REGULAR CAB STANDARD BOX, CLASSIC 1500 EXTENDED CAB LONG BOX, CLASSIC 1500 EXTENDED CAB STANDARD BOX, CLASSIC 1500 REGULAR CAB LONG BOX, CLASSIC 1500 REGULAR CAB STANDARD BOX
View related parts
Chevrolet Suburban Pan Assembly, Oil
Part Number: 10240721
$172.65 MSRP: $272.76
You Save: $100.11 (37%)
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1999 Chevrolet Suburban | 1/2 TON, 3/4 TON | 8 Cyl 7.4L
View related parts
Chevrolet Suburban Pan Assembly, Lwr Oil
Part Number: 55506665
$55.52 MSRP: $87.32
You Save: $31.80 (37%)
Product Specifications
- Other Name: Oil Pan
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Suburban | 1/2 TON | 6 Cyl 3.0L Diesel
View related parts
Chevrolet Suburban Pan Kit,W/Gasket & Magnet
Part Number: 8685921
Product Specifications
- Other Name: PAN KIT, Transmission Oil Pan; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Chevrolet Suburban | 3/4 TON | 8 Cyl 5.7L
View related parts
Chevrolet Suburban Pan Kit,W/Magnet
Part Number: 8679931
Product Specifications
- Other Name: PAN KIT, Transmission Oil Pan; Oil Pan, Pan Gasket, Transmission Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Chevrolet Suburban | 1/2 TON, 3/4 TON | 8 Cyl 5.7L, 8 Cyl 6.2L Diesel, 8 Cyl 6.5L Diesel, 8 Cyl 7.4L
View related parts
Chevrolet Suburban Pan Kit,Automatic Transmission Fluid (Pht M33 Transmission
Part Number: 24229660
Product Specifications
- Other Name: PAN KIT, Transmission Oil Pan; Transmission Pan
- Replaces: 24229791
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chevrolet Suburban | 1/2 TON, 1500 CREW CAB, 1500 CREW CAB LONG BOX, 1500 CREW CAB STANDARD BOX, 1500 EXTENDED CAB LONG BOX, 1500 EXTENDED CAB STANDARD BOX, 1500 REGULAR CAB LONG BOX, 1500 REGULAR CAB STANDARD BOX, 4 DOOR 1/2 TON, CLASSIC 1500 CREW CAB LONG BOX, CLASSIC 1500 EXTENDED CAB LONG BOX, CLASSIC 1500 EXTENDED CAB STANDARD BOX, CLASSIC 1500 REGULAR CAB LONG BOX, CLASSIC 1500 REGULAR CAB STANDARD BOX, EXT 1/2 TON, XL 1/2 TON, YUKON/DENALI | 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 6.0L, 8 Cyl 8.1L
View related parts
Chevrolet Suburban Pan Assembly, Oil
Part Number: 12559020
Product Specifications
- Other Name: PAN, Engine Oil
- Replaces: 12529174
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1999 Chevrolet Suburban | 3/4 TON | 8 Cyl 5.7L
View related parts
Chevrolet Suburban Pan,Oil
Part Number: 10054809
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1995 Chevrolet Suburban | 1/2 TON, 3/4 TON
- 1985-1988 Chevrolet Suburban | 1/2 TON, 3/4 TON
View related parts
Chevrolet Suburban Pan,Oil
Part Number: 14082348
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1986 Chevrolet Suburban | 1/2 TON, 3/4 TON | 8 Cyl 5.0L, 8 Cyl 5.7L

| Page 1 of 2 |Next >

1-20 of 30 Results

Chevrolet Suburban Oil Pan

The Chevrolet Suburban Oil Pan plays a vital role of lubrication of the engine where the oil is stored and circulated over the engine for maximum lubrication at any given time. The oil pan holds the used engine oil and accumulates it below the engine through a holding pan to avoid leakage while reheating during re-use. Again, the majority of Chevrolet Suburban cars employ some form of oil sumping, in this case wet sumping, whereby the oil pump draws the oil from the pan using the pick-up tube to lubricate the other parts of the engine before the mobilized oil falls back into the pan. The earlier models used stamped steel oil pans but modern engines use cast aluminum reservoirs that can easily be modified to enhance the performance and durability. All in all, the Chevrolet Suburban Oil Pan is one of its key components necessary for the normal operation of the engine and for its durability due to the availability of oil.

Each OEM Chevrolet Suburban Oil Pan we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Suburban Oil Pan Parts Questions & Experts Answers

Pan Assembly, Oil
12609074
Q: How to remove and install an oil pan on 4.3L V6 Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?
A: Disconnect the cable from the negative terminal of the battery. Raise the vehicle and support it securely on jackstands, drain the engine oil, and remove the oil filter. Remove the oil pan skid plate if equipped. Remove the lower crossmember from below the oil pan. On 4WD models, remove the front differential carrier. There is an engine wiring harness at the front of the oil pan. Disconnect the harness bracket. Disconnect the front exhaust Y pipe from the engine and the exhaust system and remove it from the vehicle. Remove the starter motor. Also, remove the plastic bell housing side covers. Disconnect the transmission cooler line bracket from the side of the oil pan. Disconnect the remaining wiring harness brackets. Remove the transmission-to-engine mounting bolts. Disconnect the electrical connector from the oil level sensor if equipped. Remove the transmission-to-oil pan bolts. Remove the oil pan bolts, then lower the pan from the engine. The pan will probably stick to the engine, so strike the pan with a rubber mallet until it breaks the gasket seal. Wash out the oil pan with solvent. Thoroughly clean the mounting surfaces of the oil pan and engine block of old gasket material and sealer. Wipe the gasket surfaces clean with a rag soaked in brake system cleaner. Apply a 3/16-inch wide, one-inch long bead of ATV sealant to the corners where the front cover meets the block and at the rear where the rear main cap meets the block. Then attach the new gasket to the pan, install the pan, and tighten the bolts/studs finger-light. The alignment of the rear face of the aluminum pan to the rear of the block is important. Measure between the rear face of the pan and the front face of the transmission bell housing with feeler gauges. Clearance should ideally be flush, but up to 0.011 inches is allowable. If the clearance is OK, tighten the pan bolts/studs in sequence to the torque specifications. The remainder of installation is the reverse of removal. Add the proper type and quantity of oil, start the engine, and check for leaks before placing the vehicle back in service.
Pan Assembly, Oil
12609074
Q: How to remove and replace the oil pan on V8 Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?
A: Disconnect the cable from the negative terminal of the battery. Raise the vehicle and support it securely on jackstands, drain the engine oil, and remove the oil filler. Remove the oil pan skid plate, if equipped. Unbolt the steering rack and allow it to hang out of the way. On 4WD vehicles, remove the front differential carrier. Remove the transmission bell housing covers from the rear of the engine block. Remove the crossmember. Remove the lower transmission-to-engine bolt(s). These bolts vary depending on the model of transmission used but all screw into the oil pan. Disconnect the wiring from the engine oil level sensor. Disconnect the wiring harness retainers from the oil pan. Disconnect the oil cooler lines from the oil pan on models with automatic transmissions. Remove all the oil pan bolts, then lower the pan from the engine. The pan will probably stick to the engine, so strike the pan with a rubber mallet until it breaks the gasket seal. Drill out the rivets securing the oil pan gasket to the oil pan and remove the old gasket. Wash out the oil pan with solvent. Thoroughly clean the mounting surfaces of the oil pan and engine block of old gasket material and sealant. Wipe the gasket surfaces clean with a rag soaked in brake system cleaner. Apply a 3/16-inch wide, one-inch long bead of ATV sealant to the corners of the block where the front cover and the rear cover meet the engine block. The gasket tabs protrude at these points and must have sealant around them. Attach the new gasket to the pan, install the pan, and tighten the bolts finger-tight. Be sure the oil gallery passages in the pan and the gasket are aligned properly. Install all of the oil pan mounting bolts snugly. Install the lower transmission mounting bolts snugly. Tighten the oil pan bolts and the transmission bolts to the correct torque specifications. The remainder of installation is the reverse of removal. Add the proper type and quantity of oil, start the engine, and check for leaks before placing the vehicle back in service.