My Garage
My Account
Cart
Genuine Chevrolet S10 Intake Manifold
Engine Intake Manifold- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
21 Intake Manifolds found
| Page 1 of 2 |Next >
1-20 of 21 Results
Chevrolet S10 Intake Manifold
The Intake Manifold of Chevrolet S10 vehicles helps in the distribution of either air or air/fuel mixture to the cylinders of the engine in order to gain the optimal power of the engine. Constructed often from plastic due to the materials lighter weight and superior heat dispersal properties the intake manifold maintains the equal distribution of its runners for improved combustion. Many manifolds come pre-drilled for coolant flow for better engine performance, and some are equipped with sensors that enable monitoring of the flow and pattern; types provide more horsepower and torque to the engine due to efficient distribution of the air/fuel mix. Variable length intake manifolds also prolong efficiency by controlling the speed and pressure of air delivery depending on the load requirement of the engine; all this leading to production more powerful and fuel efficient engines generally.
Each OEM Chevrolet S10 Intake Manifold we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Chevrolet S10 Intake Manifold Parts Questions & Experts Answers
- Q: How to replace an intake manifold in 2.2L four cylinder engine on Chevrolet S10?A:Disconnect the cable from the negative battery terminal. Remove the air intake duct assembly. Remove the PCV valve and hose connecting the intake manifold to the valve cover. Remove the upper intake manifold (1997 and earlier MFI models only). Tag and disconnect all electrical connectors at the throttle body and manifold. Remove the fuel lines and any wiring attached to the lower intake manifold. Remove the fuel rail bracket. Remove the spark plug wires from the coil pack. Mark the spark plug wires for reassembly. Pull them up through the intake manifold and lay them over the left side of the engine. Remove the bolt holding the heater hose tube to the right rear of the manifold. Remove the mounting nuts and separate the manifold from the Cylinder Head. Remove the EGR tube for cleaning. Remove the old gasket and transfer all components still attached to the old manifold to the new one. Before installing the manifold, clean the cylinder head and manifold gasket surfaces. Apply a thin coat of RTV sealant to the intake manifold and cylinder head mating surfaces. Place a new gasket on the manifold, hold the manifold in position against the cylinder head, and install the mounting nuts finger tight. Tighten the mounting nuts in several steps and in the correct sequence. Install the remaining components in the reverse order of removal.
- Q: How to remove and install the intake manifold in 4.3L V6 engine on Chevrolet S10?A:First off, disconnect the negative battery cable. For 1994 and 1995 VIN Z models, take out the upper fan shroud, air cleaner assembly, drain the cooling system, and disconnect the radiator as well as heater hoses. Also disassemble the spark plug wires, coil and distributor by unbolting emission relays bracket and remove rear braces from drive belt tensioner, remembering to mark relationship of distributor rotor with respect to other parts before removal. Disconnect the fuel lines at TBI unit; remove accelerator cables, cruise control cables, TV cables from manifold; detach vacuum brake booster pipe; label manifold lines & wires and remove them. Move up EGR hose whilst loosening manifold mounting bolts. Prying front of manifold loose after removing all bolts for that purpose is now allowed. In case of 1996 or later models you will need to start from taking out upper fan shroud then move on to air cleaner assembly followed by draining cooling system plus disconnecting upper hoses from radiator as well as heater. Next unbolt EGR valve and take off ignition coil carefully. Remove small brace between intake manifold & AC compressor then turn engine to TDC for number one piston-prior to removing distributor. Old gasket material must be removed to guarantee clean mating surfaces during re-installation; apply RTV sealant if necessary. Be sure new gaskets are properly aligned when putting in place new intake manifold while sealant is still wet on it. Proceed accordingly tightening recommended sequence's bolts once more when finished reverse remaining steps beginning with starting engine thereafter checking for leaks.
Related Chevrolet S10 Parts
Browse by Year
2004 Intake Manifold 2003 Intake Manifold 2002 Intake Manifold 2001 Intake Manifold 2000 Intake Manifold 1999 Intake Manifold 1998 Intake Manifold 1997 Intake Manifold 1996 Intake Manifold 1995 Intake Manifold 1994 Intake Manifold 1993 Intake Manifold 1992 Intake Manifold 1991 Intake Manifold 1990 Intake Manifold 1989 Intake Manifold 1988 Intake Manifold 1987 Intake Manifold 1986 Intake Manifold 1985 Intake Manifold 1984 Intake Manifold 1983 Intake Manifold 1982 Intake Manifold