How do you remove and replace the rear stabilizer bar,stabilizer bar bushing and stabilizer bar link on Chevrolet Impala and Monte Carlo?

To remove and replace the rear sway bar bushing kit on a vehicle, start by loosening the rear wheel lug nuts and blocking the front wheels to prevent rolling. Then, raise the rear of the vehicle and support it securely on jackstands before removing the rear wheels. Next, detach the sway bar link from the sway bar bushing kit, and if necessary, remove the rear struts to remove one or both links entirely.

How do I remove and install a front stabilizer bar,stabilizer bar bushing and stabilizer bar link for Chevrolet Impala,Monte Carlo?

To remove the sway bar kit, start by loosening the front wheel lug nuts and raising the front of the vehicle. Support it securely on jackstands and remove the front wheels. Then, remove the sway bar link nut above the sway bar by holding the link bolt at the control arm bracket and remove the links. Next, remove the bolts from the sway bar bushing brackets and pry off the brackets from the bushings if necessary. Remove the bushings from the bar, noting the direction of the split in the bushings. After that, remove the pinch-bolt from the intermediate shaft coupler to the steering gear input shaft. Support the rear part of the subframe with a floor jack and remove the two rear subframe mounting bolts. Slowly and carefully lower the subframe with the floor jack just enough to remove the sway bar kit, ensuring that the steering gear input shaft and shaft coupler separate without binding. Also, check for any wiring harnesses or hoses that may come under tension as the subframe is lowered and detach them if necessary. Carefully remove the kit and inspect the link and bar bushings for any damage. To install the sway bar kit, start by cleaning the areas on the bar where the bushings are located. Lubricate the inside and outside of the bushings with vegetable oil to simplify reassembly. Then, install the brackets and bolts, tightening them to the proper torque specifications. Slowly and carefully raise the subframe with the floor jack while guiding the steering gear input shaft into the shaft coupler. Install the pinch-bolt and tighten it to the proper torque specifications. Install the rear subframe mounting bolts and tighten them to the suitable torque specifications. Make sure to reattach any wire harnesses or brackets that were removed to lower the subframe. Install the links, tightening the link nuts to the proper torque specifications. Finally, install the wheels and lug nuts, then lower the vehicle and tighten the wheel lug nuts to the correct torque specifications.

Genuine Chevrolet Monte Carlo Sway Bar Bushing

Stabilizer Sway Bar Bushing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Sway Bar Bushings found

View related parts
Chevrolet Monte Carlo Insulator,Front Stabilizer Shaft
Part Number: 10275555
$8.53 MSRP: $15.31
You Save: $6.78 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Front
- Replaces: 25833523, 10403188
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.8L, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Insulator, Front Stabilizer Shaft *Green
Part Number: 10284149
$9.85 MSRP: $17.67
You Save: $7.82 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Front
- Replaces: 10289145, 25833525
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.8L, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Insulator, Stabilizer Shaft Link
Part Number: 6270752
$1.11 MSRP: $1.86
You Save: $0.75 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1988 Chevrolet Monte Carlo | CLASSIC 4 DOOR, CLASSIC STATION WAGON, EL CAMINO, MONTE CARLO | 6 Cyl 3.8L, 6 Cyl 4.3L, 6 Cyl 4.3L Diesel, 8 Cyl 4.4L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Chevrolet Monte Carlo Insulator, Rear Stabilizer Shaft *Green
Part Number: 10351312
$8.50 MSRP: $15.24
You Save: $6.74 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Rear
- Replaces: 10284253
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.8L, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Insulator,Front Stabilizer Shaft
Part Number: 10152155
$4.13 MSRP: $10.95
You Save: $6.82 (63%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Insulator, Rear Stabilizer Shaft *Red
Part Number: 10351313
$8.70 MSRP: $15.62
You Save: $6.92 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.8L, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Insulator, Rear Stabilizer Shaft
Part Number: 10242081
$3.50 MSRP: $10.44
You Save: $6.94 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Insulator, Front Stabilizer Shaft
Part Number: 10284183
$14.24 MSRP: $19.37
You Save: $5.13 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Insulator, Rear Stabilizer Shaft
Part Number: 10284254
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft; Bushing, Stabilizer Bar Insulator
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | IMPALA, LS, POLICE CAR | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Insulator, Front Stabilizer Shaft
Part Number: 472118
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft; Bushing, Stabilizer Bar Bushing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1988 Chevrolet Monte Carlo | CLASSIC 4 DOOR, CLASSIC STATION WAGON, EL CAMINO, MONTE CARLO | 6 Cyl 3.8L, 6 Cyl 4.3L, 6 Cyl 4.3L Diesel, 8 Cyl 4.4L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Chevrolet Monte Carlo Insulator, Rear Stabilizer Shaft
Part Number: 10248630
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Monte Carlo | LS, LS 4 DOOR, LUMINA, MONTE CARLO | 6 Cyl 3.1L, 6 Cyl 3.4L
View related parts
Chevrolet Monte Carlo Insulator,Rear Stabilizer Shaft Link
Part Number: 10270252
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Insulator, Rear Stabilizer Shaft Link
Part Number: 10270253
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Monte Carlo | LS, LS 4 DOOR, LUMINA, MONTE CARLO | 6 Cyl 3.1L, 6 Cyl 3.4L
View related parts
Chevrolet Monte Carlo Insulator, Rear Stabilizer Shaft Link
Part Number: 10288585
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2001 Chevrolet Monte Carlo | LS, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Insulator, Rear Stabilizer Shaft
Part Number: 10288584
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2001 Chevrolet Monte Carlo | LS, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Insulator, Front Stabilizer Shaft
Part Number: 10289719
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft; Bushing, Stabilizer Bar Insulator
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 Chevrolet Monte Carlo | LS, LTZ, LUMINA, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Insulator, Front Stabilizer Shaft *Yellow
Part Number: 10275556
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft; Bushing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | IMPALA, LS, POLICE CAR | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Insulator,Front Stabilizer Shaft
Part Number: 10284182
Product Specifications
- Other Name: INSULATOR, Stabilizer Shaft
- Position: Front
- Replaces: 10233858, 14087734
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ 4 DOOR, LUMINA, MONTE CARLO | 6 Cyl 3.1L, 6 Cyl 3.4L

Chevrolet Monte Carlo Sway Bar Bushing

The Sway Bar Bushing on a Chevrolet Monte Carlo car contributes to how the car moves or handles through the road by firmly holding the sway bar. It has been found that, when these rubber bushings wear out, it alters the entire attachment of the sway bar and thus jeopardizes the safety level with destabilizing performance. Different types of Sway Bar Bushing might have been installed in different models of Monte Carlo over a period of time since the beginning, and they might have some different design and function to achieve the highest performance and safety in the road. To enhance free and safe driving of your Chevrolet Monte Carlo, it is proper to routinely inspect and maintain the Sway Bar Bushing.

Each OEM Chevrolet Monte Carlo Sway Bar Bushing we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Monte Carlo Sway Bar Bushing Parts Questions & Experts Answers

Insulator, Rear Stabilizer Shaft *Red
10351313
Q: How do you remove and replace the rear stabilizer bar,stabilizer bar bushing and stabilizer bar link on Chevrolet Impala and Monte Carlo?
A: To remove and replace the rear sway bar bushing kit on a vehicle, start by loosening the rear wheel lug nuts and blocking the front wheels to prevent rolling. Then, raise the rear of the vehicle and support it securely on jackstands before removing the rear wheels. Next, detach the sway bar link from the sway bar bushing kit, and if necessary, remove the rear struts to remove one or both links entirely.
Insulator, Front Stabilizer Shaft *Green
10284149
Q: How do I remove and install a front stabilizer bar,stabilizer bar bushing and stabilizer bar link for Chevrolet Impala,Monte Carlo?
A: To remove the sway bar kit, start by loosening the front wheel lug nuts and raising the front of the vehicle. Support it securely on jackstands and remove the front wheels. Then, remove the sway bar link nut above the sway bar by holding the link bolt at the control arm bracket and remove the links. Next, remove the bolts from the sway bar bushing brackets and pry off the brackets from the bushings if necessary. Remove the bushings from the bar, noting the direction of the split in the bushings. After that, remove the pinch-bolt from the intermediate shaft coupler to the steering gear input shaft. Support the rear part of the subframe with a floor jack and remove the two rear subframe mounting bolts. Slowly and carefully lower the subframe with the floor jack just enough to remove the sway bar kit, ensuring that the steering gear input shaft and shaft coupler separate without binding. Also, check for any wiring harnesses or hoses that may come under tension as the subframe is lowered and detach them if necessary. Carefully remove the kit and inspect the link and bar bushings for any damage. To install the sway bar kit, start by cleaning the areas on the bar where the bushings are located. Lubricate the inside and outside of the bushings with vegetable oil to simplify reassembly. Then, install the brackets and bolts, tightening them to the proper torque specifications. Slowly and carefully raise the subframe with the floor jack while guiding the steering gear input shaft into the shaft coupler. Install the pinch-bolt and tighten it to the proper torque specifications. Install the rear subframe mounting bolts and tighten them to the suitable torque specifications. Make sure to reattach any wire harnesses or brackets that were removed to lower the subframe. Install the links, tightening the link nuts to the proper torque specifications. Finally, install the wheels and lug nuts, then lower the vehicle and tighten the wheel lug nuts to the correct torque specifications.