How to remove and install the door latch assembly,Door Handle and Door Lock Cylinder on Chevrolet Malibu?

Before the actual welding begins it is required to turn off the cable from the negative terminal of the battery. The door latch procedure is as follows: it is applicable to a 2016 and later Malibu, and for a 2015 and earlier, there would be similar steps. First, you have to take of the door trim panel as well as the watershield. Next, remove the door window glass and the door window glass regulator; for 2015 and the earlier model, you have only removed the left side bolts of the window regulator. Move on to the removal of the window guide rear track having first unscrewed the lower bolt together with disconnecting wiring harness clips. Turn the outside handle clockwise and anti-clockwise to unlock and take it off, followed by removing the handle inner bracket; disconnect the electrical connector, take out the latch mounting fasteners, and then pull the latch assembly through the door opening. If needed, remove the rod and cables from the latch assembly, paying attention to the position of the lock rod and place all these components to the new latch assembly. In the process of installation, all the functions are reversed and then tested before reinstalling the door trim panel. If the model incorporates smart key entry system, then pull off the door trim panel along with the watershield, run the regulator to bring the glass into the upper most position. To disarm the outside handle, using the fingers, one has to twist off the layer made of hard plastic from the lock cylinder metal covering, undo the holding bolt and then finally pull up the handle towards the back of the car and rotate it further clockwise. If the vehicle is fitted with the smart key system, pull the handle electrical connector on the inside. The removal sequence is as follows; the consequent step will make the door trim panel function well before it is reattached. For the outside handle inner bracket: first, take out the window regulator assembly and also the window guide rear track, after which take out the outside handle. To release the inner bracket, there is a bolt to undo, the retaining tabs have to be pressed and the inner bracket has to be pulled towards the front of the car while the latch rod and cable are being detached. The procedure of its removal is vice versa, before removing, the door check must be tested for proper functioning, as well as the door trim panel is reinstalled back. For the lock cylinder, to open, the user has to take off the outside handle inner bracket and then press on tabs and the lock cylinder would be pulled out. The disassembly goes in a backward manner done to ensure all functions are checked before reinstalling the door trim panel. For 2015 and earlier models, if the vehicle has a smart key entry system, then the door trim panel and its related watershield must be removed, pass the relevant window motor constantly to shut the glass in its highest positions, and demate the outside handle electrical connector then. Should the lock cylinder has become stiff, more turn are likely to be necessary, but do not turn past two and half after the initial turn. Take off the small cover of the door and with the outside door handle pulled out, while at the same time rotating the lock cylinder screw in an anti clock wise direction, while sliding the handle backwards and rotating it anti-clockwise. The process is the opposite of the removal of the MPP, and all the connections are proved before the door trim panel is reattached. For the outside handle inner bracket, you will have to take off the door trim panel and the watershield, and then using the window motor to bring the glass up and then take off the window guide rear track. Remove the outside handle and lock cylinder, unscrew the bracket screw, depush safety clips which are made of plastic, detach the rods and, if any, electrical contacts. Carefully pull out the handle inner bracket and what is needed to be transferred to the new bracket and the installation is done in a reverse manner after cross-checking the functionalities before putting back the door trim panel.

Genuine Chevrolet Malibu Door Handle

Inside Door Handle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

117 Door Handles found

View related parts
Chevrolet Malibu Handle Assembly, Front/Rear Side Door Outside *Ex Brt Chrom
Part Number: 22867272
$37.68 MSRP: $56.08
You Save: $18.40 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front and Rear
- Replaces: 15929514, 22835654
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2012 Chevrolet Malibu | LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.2L, 4 Cyl 2.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.6L
View related parts
Chevrolet Malibu Handle, Rear Compartment Lid Pull *Black
Part Number: 95460708
$12.65 MSRP: $19.17
You Save: $6.52 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Rear Compartment; Handle, Pull Handle
- Position: Rear
- Replaces: 12785350
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2016 Chevrolet Malibu | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
Chevrolet Malibu Handle Kit, Front Side Door Outside (Chrome Button)
Part Number: 13577716
$171.87 MSRP: $258.12
You Save: $86.25 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE KIT, Door Outside Handle; Outside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chevrolet Malibu | LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Chevrolet Malibu Handle Kit, Front Side Door Outside
Part Number: 13521820
$72.34 MSRP: $108.15
You Save: $35.81 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle Kit, Front S/D O/S; Inside Handle, Outside Handle
- Position: Front
- Replaces: 13511135
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2024 Chevrolet Malibu | L 4 DOOR NOTCHBACK, LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LT HYBRID 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK, RS 4 DOOR NOTCHBACK | 4 Cyl 1.5L, 4 Cyl 1.8L, 4 Cyl 2.0L
View related parts
Chevrolet Malibu Handle Assembly, Front Side Door Outside *Service Primer
Part Number: 92233089
$65.20 MSRP: $98.80
You Save: $33.60 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chevrolet Malibu | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Chevrolet Malibu Handle Assembly, Rear Compartment Lid Inside
Part Number: 20814017
$22.19 MSRP: $33.17
You Save: $10.98 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Rear Compartment Lid Release or Ajar; Emergency Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chevrolet Malibu | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Chevrolet Malibu Handle,Front Side Door Outside
Part Number: 25936893
$96.59 MSRP: $143.76
You Save: $47.17 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chevrolet Malibu | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Chevrolet Malibu Handle Assembly, Rear Side Door Outside
Part Number: 10439378
$12.60 MSRP: $18.75
You Save: $6.15 (33%)
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Rear
- Replaces: 10285449, 10275251, 10275243, 10406557, 10275253, 10439616, 10406559, 10439606, 10439614, 10275241, 10439604, 10275257, 10308591, 10439612, 10439622, 10406581, 10439618, 10444212
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Chevrolet Malibu | 4 DOOR, 4 DOOR NOTCHBACK, CLASSIC 4 DOOR NOTCHBACK, LS 4 DOOR, LS 4 DOOR NOTCHBACK, LX 4 DOOR | 4 Cyl 2.2L, 4 Cyl 2.4L, 6 Cyl 3.1L
View related parts
Chevrolet Malibu Handle Assembly, Front Side Door Outside
Part Number: 10439372
$55.69 MSRP: $82.88
You Save: $27.19 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front
- Replaces: 10295457, 10439530, 10439532, 10275186, 10286428, 10256723, 10275184, 10439542, 10439514, 10444204, 10275190, 10275196, 10256725, 10281765, 10289475, 10439528, 10439536, 10439524, 10277104, 10406575, 10403777, 10288255, 10439516, 10298986, 10406551, 10439512
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Chevrolet Malibu | 4 DOOR, 4 DOOR NOTCHBACK, CLASSIC 4 DOOR NOTCHBACK, LS 4 DOOR, LS 4 DOOR NOTCHBACK, LX 4 DOOR | 4 Cyl 2.2L, 4 Cyl 2.4L, 6 Cyl 3.1L
View related parts
Chevrolet Malibu Handle Kit, Rear Side Door Outside
Part Number: 13577718
$132.37 MSRP: $197.02
You Save: $64.65 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE KIT, Door Outside Handle; Door Trim Panel, Outside Handle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chevrolet Malibu | LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Chevrolet Malibu Handle Pkg, Front & Rear Side Door Outside *Atlantis Mount
Part Number: 22817278
$94.61 MSRP: $145.00
You Save: $50.39 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2015 Chevrolet Malibu | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Chevrolet Malibu Handle Assist Handle *G*Shale
Part Number: 22605901
$40.72 MSRP: $78.00
You Save: $37.28 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Rear Quarter and Roof Rail Assist; Assist Strap
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2003 Chevrolet Malibu | 4 DOOR, 4 DOOR NOTCHBACK, LS 4 DOOR, LS 4 DOOR NOTCHBACK, LX 4 DOOR | 4 Cyl 2.4L, 6 Cyl 3.1L
View related parts
Chevrolet Malibu Handle,Front Side Door Outside
Part Number: 22867552
$40.62 MSRP: $63.88
You Save: $23.26 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front
- Replaces: 15916609, 22836819
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2012 Chevrolet Malibu | 4 DOOR HYBRID, LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK | 4 Cyl 2.2L, 4 Cyl 2.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.6L
View related parts
Chevrolet Malibu Handle Assembly, Front S/D I/S *Chrome M
Part Number: 84593759
$22.01 MSRP: $34.61
You Save: $12.60 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Inside Handle
- Position: Front
- Replaces: 22853825
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chevrolet Malibu | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Chevrolet Malibu Handle Kit, Front Side Door Outside
Part Number: 13511252
$35.83 MSRP: $56.34
You Save: $20.51 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE KIT, Door Outside Handle; Outside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016 Chevrolet Malibu | L 4 DOOR NOTCHBACK, LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LT HYBRID 4 DOOR NOTCHBACK | 4 Cyl 1.5L, 4 Cyl 1.8L, 4 Cyl 2.0L
View related parts
Chevrolet Malibu Handle Assembly, Front S/D I/S *Int Br Chrom
Part Number: 84593760
$14.57 MSRP: $21.79
You Save: $7.22 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chevrolet Malibu | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L
View related parts
Chevrolet Malibu Handle Kit, Rear Side Door Outside
Part Number: 13521804
$63.45 MSRP: $94.87
You Save: $31.42 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle Kit, Rear S/D O/S; Door Handle, Outside Handle
- Position: Rear
- Replaces: 13518116, 13511133
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2018 Chevrolet Malibu | L 4 DOOR NOTCHBACK, LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LT HYBRID 4 DOOR NOTCHBACK | 4 Cyl 1.5L, 4 Cyl 1.8L, 4 Cyl 2.0L
View related parts
Chevrolet Malibu Handle Assembly, Front Side Door Inside *Chrome
Part Number: 22884885
$83.07 MSRP: $124.19
You Save: $41.12 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Front
- Replaces: 25996949
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2012 Chevrolet Malibu | 4 DOOR HYBRID, LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.6L
View related parts
Chevrolet Malibu Lever Assembly, Front & Rear Side Door Outside Handle *Less Finish
Part Number: 22672194
$30.96 MSRP: $46.29
You Save: $15.33 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: LEVER, Door Outside Handle; Outside Handle
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chevrolet Malibu | 4 DOOR HATCHBACK, 4 DOOR NOTCHBACK, BASE 4 DOOR NOTCHBACK, LS 4 DOOR HATCHBACK, LS 4 DOOR NOTCHBACK, LT 4 DOOR HATCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR HATCHBACK, LTZ 4 DOOR NOTCHBACK, MAXX SS 4 DOOR HATCHBACK, SS 4 DOOR NOTCHBACK | 4 Cyl 2.2L, 4 Cyl 2.4L, 6 Cyl 3.5L, 6 Cyl 3.6L, 6 Cyl 3.9L
View related parts
Chevrolet Malibu Handle Pkg, Front & Rear Side Door Outside *Chmp Silv Mount
Part Number: 22817277
Product Specifications
- Other Name: HANDLE PKG, Exterior Door
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chevrolet Malibu | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.0L, 4 Cyl 2.4L, 4 Cyl 2.5L

| Page 1 of 6 |Next >

1-20 of 117 Results

Chevrolet Malibu Door Handle

The operation of the Subject of the study known as Interior Door Handle of Chevrolet Malibu enables occupants to leave the car comfortably. This small lever works in a unison with the door by unhooking the hook from the latch as is the case with the handle from the exterior. Eventually, the door handle's inside part which is the Chevrolet Malibu's Interior Door Handle becomes worn out because of daily use specifically the driver side handle where it may result to spots that causes unattractive appearance. Tip: there are various Chevrolet Malibu models Different types of Interior Door Handles have been used in Chevrolet Malibu models, but the variations to each are not stated. Regardless of the style, the primary mechanism remains consistent: a bar which interacts with the door latch assembly. Any problems with the Interior Door Handle or the latch assembly will affect the operation of the door locking system creating discomfort to users.

Each OEM Chevrolet Malibu Door Handle we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Malibu Door Handle Parts Questions & Experts Answers

Handle Assembly, Roof Rail Rear Asst *Light Ttnum
95025626
Q: How to remove and install the door latch assembly,Door Handle and Door Lock Cylinder on Chevrolet Malibu?
A: Before the actual welding begins it is required to turn off the cable from the negative terminal of the battery. The door latch procedure is as follows: it is applicable to a 2016 and later Malibu, and for a 2015 and earlier, there would be similar steps. First, you have to take of the door trim panel as well as the watershield. Next, remove the door window glass and the door window glass regulator; for 2015 and the earlier model, you have only removed the left side bolts of the Window Regulator. Move on to the removal of the window guide rear track having first unscrewed the lower bolt together with disconnecting wiring harness clips. Turn the outside handle clockwise and anti-clockwise to unlock and take it off, followed by removing the handle inner bracket; disconnect the electrical connector, take out the latch mounting fasteners, and then pull the latch assembly through the door opening. If needed, remove the rod and cables from the latch assembly, paying attention to the position of the lock rod and place all these components to the new latch assembly. In the process of installation, all the functions are reversed and then tested before reinstalling the door trim panel. If the model incorporates smart key entry system, then pull off the door trim panel along with the watershield, run the regulator to bring the glass into the upper most position. To disarm the outside handle, using the fingers, one has to twist off the layer made of hard plastic from the lock cylinder metal covering, undo the holding bolt and then finally pull up the handle towards the back of the car and rotate it further clockwise. If the vehicle is fitted with the smart key system, pull the handle electrical connector on the inside. The removal sequence is as follows; the consequent step will make the door trim panel function well before it is reattached. For the outside handle inner bracket: first, take out the window regulator assembly and also the window guide rear track, after which take out the outside handle. To release the inner bracket, there is a bolt to undo, the retaining tabs have to be pressed and the inner bracket has to be pulled towards the front of the car while the latch rod and cable are being detached. The procedure of its removal is vice versa, before removing, the door check must be tested for proper functioning, as well as the door trim panel is reinstalled back. For the lock cylinder, to open, the user has to take off the outside handle inner bracket and then press on tabs and the lock cylinder would be pulled out. The disassembly goes in a backward manner done to ensure all functions are checked before reinstalling the door trim panel. For 2015 and earlier models, if the vehicle has a smart key entry system, then the door trim panel and its related watershield must be removed, pass the relevant window motor constantly to shut the glass in its highest positions, and demate the outside handle electrical connector then. Should the lock cylinder has become stiff, more turn are likely to be necessary, but do not turn past two and half after the initial turn. Take off the small cover of the door and with the outside door handle pulled out, while at the same time rotating the lock cylinder screw in an anti clock wise direction, while sliding the handle backwards and rotating it anti-clockwise. The process is the opposite of the removal of the MPP, and all the connections are proved before the door trim panel is reattached. For the outside handle inner bracket, you will have to take off the door trim panel and the watershield, and then using the window motor to bring the glass up and then take off the window guide rear track. Remove the outside handle and lock cylinder, unscrew the bracket screw, depush safety clips which are made of plastic, detach the rods and, if any, electrical contacts. Carefully pull out the handle inner bracket and what is needed to be transferred to the new bracket and the installation is done in a reverse manner after cross-checking the functionalities before putting back the door trim panel.