How to replace disc brake pads?

Disc brake pads must be replaced on both front or both rear wheels at the same time-never replace the pads on only one wheel. Also, the dust created by the brake system is harmful to your health. Never blow it out with compressed air and don't inhale any of it. An approved filtering mask should be worn when working on the brakes. Do not, under any circumstances, use petroleum-based solvents to clean brake parts. Use brake system cleaner only! This procedure applies to front and rear disc brakes. Remove the cap from the brake fluid reservoir and remove about two-thirds of the fluid. Brake fluid will damage paint. Cover all painted surfaces around the work area and be careful not to spill fluid during this procedure. Clean any spilled fluid immediately and rinse the area with lots of water. Loosen the wheel lug nuts, raise the end of the vehicle you're working on and support it securely on jack stands. Block the wheels at the opposite end. Remove the wheels. Work on one brake assembly at a time, using the assembled brake for reference if necessary. Inspect the brake disc carefully. If machining is necessary, follow the information to remove the disc, at which time the pads can be removed as well. On front brakes and rear brakes with parking brake shoes (instead of actuator-type calipers), push the piston back into its bore to provide room for the new brake pads. A C-clamp can be used to accomplish this. As the piston is depressed to the bottom of the caliper bore, the fluid in the master cylinder will rise. Make sure that it doesn't overflow. If necessary, siphon off some of the fluid. Do not attempt to depress the piston into the caliper on later models with parking brake actuator-type calipers. Once you have installed the new pads, proceed. Install the wheel and lug nuts, lower the vehicle and tighten the lug nuts to the torque. Apply and release the brake pedal several times to bring the pads into contact with the brake discs. Check the brake fluid level and add fluid, if necessary. Check the operation of the brakes in an isolated area before driving the vehicle in traffic.

Genuine Chevrolet Impala Brake Pad

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Brake Pads found

View related parts
Chevrolet Impala Pad Kit,Front Disc Brake
Part Number: 19152666
$68.30 MSRP: $135.52
You Save: $67.22 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Replaces: 18042214, 18045380, 18048030, 18042442, 88964119
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Pad Kit,Front Disc Brake
Part Number: 19207421
$115.13 MSRP: $217.22
You Save: $102.09 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Replaces: 88967233
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2016 Chevrolet Impala | LS, LS POLICE CAR, LT, LT 3.5, LTZ, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.6L, 6 Cyl 3.9L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Pad Kit,Rear Disc Brake
Part Number: 18048690
$85.02 MSRP: $154.58
You Save: $69.56 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Rear Pad
- Position: Rear
- Replaces: 19209499
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2016 Chevrolet Impala | LS, LTZ | 6 Cyl 3.5L Flex, 6 Cyl 3.6L, 6 Cyl 3.9L Flex
View related parts
Chevrolet Impala Pad Kit, Front Disc Brk
Part Number: 84233325
$80.16 MSRP: $159.04
You Save: $78.88 (50%)
ADD TO CART
Product Specifications
- Other Name: Brake Pad, Front Pad
- Position: Front
- Replaces: 23316342, 20963796
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
Chevrolet Impala Pad Kit,Front Disc Brake
Part Number: 19207501
$74.09 MSRP: $167.69
You Save: $93.60 (56%)
ADD TO CART
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Replaces: 15270292
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2010 Chevrolet Impala | LS, LS POLICE CAR, LT, LT 3.5, LTZ, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Pad Kit,Rear Disc Brake
Part Number: 18042417
$40.82 MSRP: $115.71
You Save: $74.89 (65%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Rear Pad
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | IMPALA, LS, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Pad Kit, Rear Disc Brk
Part Number: 85143529
$76.75 MSRP: $152.29
You Save: $75.54 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Pad, Rear Pad
- Position: Rear
- Replaces: 13237768, 84144898, 20978663, 22846361
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | LS 4 DOOR NOTCHBACK, LT 4 DOOR NOTCHBACK, LTZ 4 DOOR NOTCHBACK | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
Chevrolet Impala Pad Kit,Front Disc Brake
Part Number: 18029828
$32.62 MSRP: $114.00
You Save: $81.38 (72%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Chevrolet Impala | IMPALA, LS, POLICE CAR | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Pad Kit,Rear Disc Brake
Part Number: 19209340
$74.94 MSRP: $134.42
You Save: $59.48 (45%)
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Rear Pad
- Position: Rear
- Replaces: 88967229, 18045984
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2010 Chevrolet Impala | LS, LS POLICE CAR, LT, LT 3.5, LTZ, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Pad Kit,Front Disc Brake
Part Number: 19152057
Product Specifications
- Other Name: PAD KIT, Brake; Front Pad
- Position: Front
- Replaces: 12321452, 18024914, 12510010, 18024921, 18024904, 18024920
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | CLASSIC 4 DOOR, CLASSIC STATION WAGON, LS 4 DOOR | 8 Cyl 5.7L
View related parts
Chevrolet Impala Pad Kit,Rear Disc Brake
Part Number: 19152685
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Rear Pad
- Position: Rear
- Replaces: 18023377, 18029844
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chevrolet Impala | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Pad Kit,Front Disc Brake
Part Number: 19260481
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2016 Chevrolet Impala | LS, LTZ | 6 Cyl 3.5L Flex, 6 Cyl 3.6L, 6 Cyl 3.9L Flex
View related parts
Chevrolet Impala Pad Kit,Front Disc Brake
Part Number: 18024928
Product Specifications
- Other Name: PAD KIT, Brake; Front Pad
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | CLASSIC 4 DOOR, CLASSIC STATION WAGON, LS 4 DOOR | 8 Cyl 5.7L
View related parts
Chevrolet Impala Pad Kit,Rear Disc Brake
Part Number: 18021521
Product Specifications
- Other Name: PAD KIT, Brake; Rear Pad
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | CLASSIC 4 DOOR, LS 4 DOOR | 8 Cyl 5.7L
View related parts
Chevrolet Impala Pad Kit,Front Disc Brake
Part Number: 19167302
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Replaces: 18024931
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Impala | LUMINA | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Impala Pad Kit,Front Disc Brake
Part Number: 18024927
Product Specifications
- Other Name: PAD KIT, Brake; Front Pad
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | CLASSIC 4 DOOR, LS 4 DOOR | 8 Cyl 5.7L

Chevrolet Impala Brake Pad

Chevrolet Impala Brake Pad is part of the braking system that is used in producing the friction that is needed on the brake rotors to enable the stopping of the car. These pads are made up of a friction material that is deposited on a metal base plate and are eventually used up by natural wear and tear and therefore need to be replaced. Most of Impala models have wear sensors or wear indicators that inform clients when the pads reach their barest minimum measurements to be replaced. A number of brake pad materials have been fitted to Chevrolet Impala cars over the years ranging from the non- metallic, semi metallic, full metallic and ceramic. All of them has unique characteristics concerning friction, wear and noise. In addition to this, the associated hardware such as clips and springs should also be replaced for the brake pad to work for as long as possible and to perfection. Service intervals should be carried out with brake system in normal condition at least every 50,000 miles to guarantee better braking and avoid matters like brake fade.

Each OEM Chevrolet Impala Brake Pad we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Impala Brake Pad Parts Questions & Experts Answers

Pad Kit,Rear Disc Brake
18048690
Q: How to replace disc brake pads?
A: Disc brake pads must be replaced on both front or both rear wheels at the same time-never replace the pads on only one wheel. Also, the dust created by the brake system is harmful to your health. Never blow it out with compressed air and don't inhale any of it. An approved filtering mask should be worn when working on the brakes. Do not, under any circumstances, use petroleum-based solvents to clean brake parts. Use brake system cleaner only! This procedure applies to front and rear disc brakes. Remove the cap from the brake fluid reservoir and remove about two-thirds of the fluid. Brake fluid will damage paint. Cover all painted surfaces around the work area and be careful not to spill fluid during this procedure. Clean any spilled fluid immediately and rinse the area with lots of water. Loosen the wheel lug nuts, raise the end of the vehicle you're working on and support it securely on jack stands. Block the wheels at the opposite end. Remove the wheels. Work on one brake assembly at a time, using the assembled brake for reference if necessary. Inspect the Brake Disc carefully. If machining is necessary, follow the information to remove the disc, at which time the pads can be removed as well. On front brakes and rear brakes with Parking Brake Shoes (instead of actuator-type calipers), push the piston back into its bore to provide room for the new brake pads. A C-clamp can be used to accomplish this. As the piston is depressed to the bottom of the caliper bore, the fluid in the master cylinder will rise. Make sure that it doesn't overflow. If necessary, siphon off some of the fluid. Do not attempt to depress the piston into the caliper on later models with parking brake actuator-type calipers. Once you have installed the new pads, proceed. Install the wheel and lug nuts, lower the vehicle and tighten the lug nuts to the torque. Apply and release the brake pedal several times to bring the pads into contact with the brake discs. Check the brake fluid level and add fluid, if necessary. Check the operation of the brakes in an isolated area before driving the vehicle in traffic.