How do I remove and install a Steering Knuckle?

To remove the driveaxle/hub assembly, start by loosening the driveaxle/hub nut and also for the wheel lug nuts. Then lift up vehicle and support it well on jackstands. Take off the wheel and put a mark on position of strut to steering knuckle. Loosen but do not remove bolts for strut to steering knuckles. Remove tie rod end from steering knuckle arm and if necessary, take out hub and bearing assembly from knuckle. Remove ball joint from steering knuckle, press driveaxle from hub with wire supporting it at end and finally separate strut from steering knuckle. For installation of drive axle/hub assembly guide the knuckle and hub assembly into position thereby inserting driveaxle into hub. Push down the knuckle into strut flange while fitting bolts and nuts, without tightening them yet.Connect balljoint to the steering knuckle then tighten its nut until specified torque is reached.Connect tie-rod end to the steering knuckle arm then firmly tighten strut bolt nuts as well as balljoint-to-control arm bolt/nuts, tie-rod nut in addition to cotter pins.Replace all broken cotter pins.Place brake disc on hub, install caliper plus wheel speed sensor.Install another new Drive Axle/Hub Nut tightening securely.Put back wheel plus lug nuts; lower vehicle upon which tighten lug nuts according to specified torque.Use appropriate wrench to finally tighten Drive Axle/Hub Nut specifically to referred torsion value.

Genuine Chevrolet Equinox Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Steering Knuckles found

View related parts
Chevrolet Equinox Knuckle Assembly, Rear Suspension
Part Number: 84034344
$73.73 MSRP: $128.32
You Save: $54.59 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: KNUCKLE, Rear Wheel; Knuckle
- Position: Rear
- Replaced by: 87825520
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2021 Chevrolet Equinox | 4 DOOR BASE (GMNA), 4 DOOR LT (GMNA), 4 DOOR LTZ (GMNA) | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L
View related parts
Chevrolet Equinox Steering Knuckle
Part Number: 84210077
$61.88 MSRP: $107.70
You Save: $45.82 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering ; Knuckle, Strg; Knuckle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2021 Chevrolet Equinox | 4 DOOR BASE (GMNA), 4 DOOR LT (GMNA), 4 DOOR LTZ (GMNA) | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L
View related parts
Chevrolet Equinox Knuckle Assembly, Rear Suspension
Part Number: 84034343
$77.53 MSRP: $128.32
You Save: $50.79 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: KNUCKLE, Rear Wheel; Knuckle
- Position: Rear
- Replaced by: 87825519
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2021 Chevrolet Equinox | 4 DOOR BASE (GMNA), 4 DOOR LT (GMNA), 4 DOOR LTZ (GMNA) | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L
View related parts
Chevrolet Equinox Steering Knuckle
Part Number: 84210076
$61.29 MSRP: $106.67
You Save: $45.38 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering ; Knuckle, Strg; Knuckle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2021 Chevrolet Equinox | 4 DOOR BASE (GMNA), 4 DOOR LT (GMNA), 4 DOOR LTZ (GMNA) | 4 Cyl 1.5L, 4 Cyl 1.6L Diesel, 4 Cyl 2.0L
View related parts
Chevrolet Equinox Rear Suspension Knuckle Assembly
Part Number: 23337210
$74.57 MSRP: $117.33
You Save: $42.76 (37%)
Product Specifications
- Other Name: Knuckle Assembly, Rear Suspension; Knuckle
- Position: Rear
- Replaces: 22873264, 25918953, 25982348
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV, SUV AWD, SUV FWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Rear Suspension Knuckle Assembly
Part Number: 23337211
$74.57 MSRP: $117.33
You Save: $42.76 (37%)
Product Specifications
- Other Name: Knuckle Assembly, Rear Suspension; Knuckle
- Position: Rear
- Replaces: 25918954, 22873265
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV, SUV AWD, SUV FWD | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Steering Knuckle
Part Number: 22786978
$213.31 MSRP: $337.14
You Save: $123.83 (37%)
Product Specifications
- Other Name: Knuckle, Steering ; Knuckle, Steering; Knuckle
- Replaces: 25978806
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Steering Knuckle
Part Number: 22786979
$213.31 MSRP: $337.14
You Save: $123.83 (37%)
Product Specifications
- Other Name: Knuckle, Steering ; Knuckle, Steering; Knuckle
- Replaces: 25978805
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2017 Chevrolet Equinox | LS SUV, LT SUV, LTZ SUV | 4 Cyl 2.4L, 6 Cyl 3.0L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Rear Suspension Knuckle
Part Number: 89047805
Product Specifications
- Other Name: Knuckle,Rear Suspension; Knuckle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Equinox | SUV AWD, SUV FWD | 6 Cyl 3.4L
View related parts
Chevrolet Equinox Rear Suspension Knuckle
Part Number: 89047806
Product Specifications
- Other Name: Knuckle,Rear Suspension; Knuckle
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Equinox | SUV AWD, SUV FWD | 6 Cyl 3.4L
View related parts
Chevrolet Equinox Steering Knuckle Assembly
Part Number: 22702779
Product Specifications
- Other Name: Knuckle Assembly, Steering ; Knuckle, Steering; Knuckle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Equinox | SUV AWD, SUV FWD, SUV LT AWD, SUV LT FWD | 6 Cyl 3.4L
View related parts
Chevrolet Equinox Steering Knuckle Assembly
Part Number: 22702780
Product Specifications
- Other Name: Knuckle Assembly, Steering ; Knuckle, Steering; Knuckle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Equinox | SUV AWD, SUV FWD, SUV LT AWD, SUV LT FWD | 6 Cyl 3.4L
View related parts
Chevrolet Equinox Steering Knuckle
Part Number: 15837011
Product Specifications
- Other Name: Knuckle,Steering; Knuckle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2009 Chevrolet Equinox | SS SUV AWD, SS SUV FWD, SUV AWD, SUV FWD, SUV LT AWD, SUV LT FWD | 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Rear Suspension Knuckle Assembly
Part Number: 23343506
Product Specifications
- Other Name: Knuckle Assembly, Rear Suspension; Knuckle
- Position: Rear
- Replaces: 22864823, 25927799
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Chevrolet Equinox | SUV AWD, SUV FWD | 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Rear Suspension Knuckle Assembly
Part Number: 23343507
$293.17 MSRP: $463.36
You Save: $170.19 (37%)
Product Specifications
- Other Name: Knuckle Assembly, Rr Susp; Knuckle
- Position: Rear
- Replaces: 22864824, 25937773
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Chevrolet Equinox | SUV AWD, SUV FWD | 6 Cyl 3.4L, 6 Cyl 3.6L
View related parts
Chevrolet Equinox Knuckle Steering
Part Number: 15837014
Product Specifications
- Other Name: Knuckle,Steering; Knuckle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2009 Chevrolet Equinox | SS SUV AWD, SS SUV FWD, SUV AWD, SUV FWD, SUV LT AWD, SUV LT FWD | 6 Cyl 3.4L, 6 Cyl 3.6L

Chevrolet Equinox Steering Knuckle

The Steering Knuckle of Chevrolet Equinox vehicles is still a control arm link that joins the front wheels with the suspension and steering assemblies. It is the place where control arms, tie rod ends and spindle or hubs to which the wheels are fixed are attached. Depending on the type of the drivetrain, the Knuckle may contain an integral spindle or just the hub with the roller bearing in form of tapered ones. In term of suspension, the transition from kingpins to ball joints is seen in steering knuckles to prove innovation of the equipment. An example of the function of the Knuckle is during replacing of ball joints or tie-rod ends, thus, constant check up of the Knuckle is often advised.

Each OEM Chevrolet Equinox Steering Knuckle we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Equinox Steering Knuckle Parts Questions & Experts Answers

Steering Knuckle
22786978
Q: How do I remove and install a Steering Knuckle?
A: To remove the driveaxle/hub assembly, start by loosening the driveaxle/hub nut and also for the wheel lug nuts. Then lift up vehicle and support it well on jackstands. Take off the wheel and put a mark on position of strut to steering knuckle. Loosen but do not remove bolts for strut to steering knuckles. Remove Tie Rod End from steering knuckle arm and if necessary, take out hub and bearing assembly from knuckle. Remove Ball Joint from steering knuckle, press driveaxle from hub with wire supporting it at end and finally separate strut from steering knuckle. For installation of drive axle/hub assembly guide the knuckle and hub assembly into position thereby inserting driveaxle into hub. Push down the knuckle into strut flange while fitting bolts and nuts, without tightening them yet.Connect balljoint to the steering knuckle then tighten its nut until specified torque is reached.Connect tie-rod end to the steering knuckle arm then firmly tighten strut bolt nuts as well as balljoint-to-control arm bolt/nuts, tie-rod nut in addition to cotter pins.Replace all broken cotter pins.Place brake disc on hub, install caliper plus wheel speed sensor.Install another new Drive Axle/Hub Nut tightening securely.Put back wheel plus lug nuts; lower vehicle upon which tighten lug nuts according to specified torque.Use appropriate wrench to finally tighten Drive Axle/Hub Nut specifically to referred torsion value.

Related Chevrolet Equinox Parts

Browse by Year

2021 Steering Knuckle 2020 Steering Knuckle 2019 Steering Knuckle 2018 Steering Knuckle 2017 Steering Knuckle 2016 Steering Knuckle 2015 Steering Knuckle 2014 Steering Knuckle 2013 Steering Knuckle 2012 Steering Knuckle 2011 Steering Knuckle 2010 Steering Knuckle 2009 Steering Knuckle 2008 Steering Knuckle 2007 Steering Knuckle 2006 Steering Knuckle 2005 Steering Knuckle