My Garage
My Account
Cart
Genuine Chevrolet Colorado CV Boot
Axle Boot- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
6 CV Boots found
Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Cv Joint
Part Number: 23474674$29.10 MSRP: $73.22You Save: $44.12 (61%)
Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Tri, Pot Joint
Part Number: 23474673$50.15 MSRP: $87.29You Save: $37.14 (43%)Ships in 1-3 Business Days
Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Cv Joint Inner
Part Number: 84243437$70.98 MSRP: $111.70You Save: $40.72 (37%)
Chevrolet Colorado Boot Kit,Front Wheel Drive Shaft Cv Joint (Inboard & Outboard)
Part Number: 89040354
Chevrolet Colorado Boot Kit, Front Wheel Drive Shaft Cv Joint Outer
Part Number: 84243444$67.11 MSRP: $105.60You Save: $38.49 (37%)
Chevrolet Colorado Boot Kit,Front Wheel Drive Shaft Double Offset Joint (Outboard)
Part Number: 89040355
Chevrolet Colorado CV Boot
The CV Boot in Chevrolet Colorado vehicles is an important guard that protects the CV Joint whereby the power from the transaxle to the wheels is transferred. There are several forms of CV Joints used on the Colorado vehicles including the fixed on the outermost end and the plunging on the inner side. The CV Boot is intended to arrest exposure of the CV Joint to contaminants and to conserve the lubricant, thus reducing joint failure. It is therefore recommended and advised that Chevrolet Colorado vehicles underwent frequent inspection of the CV Boot for any signs of damage and this is aimed at promoting the maximum performance as well as the durability of the CV Joint.
Each OEM Chevrolet Colorado CV Boot we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Chevrolet Colorado CV Boot Parts Questions & Experts Answers
- Q: How to replace CV joint boots?A: Before starting the job of replacing CV boots, it is important to explore all options. A complete rebuilt driveaxles can be obtained on an exchange basis which is less time consuming. Check the cost and availability of parts before disassembling the vehicle. The driveaxle should be placed in a vise lined with rags to protect the axleshaft when replacing the inner boot. Check for excessive play and smooth operation of the CV joint. Where a boot is torn, a joint must be removed, cleaned, and inspected for damage. Some models may have a protective cover which has to be removed in order to get at the boots. The old boot clamps must be cut off and the wire retainer ring pried off to replace the inner boot. Then, the outer race may come out by pulling it off while the snap-ring should be removed from the axleshaft. Prying apart the inner race and cage helps in removing balls inside it. Lastly, inspect for damage of inner race, cage, and balls that are present in any model. Wrap Axle Shaft splines with tape so as not to damage the boot, slide small clamp and then boot onto the axleshaft. Put inner race and cage assembly in place then pack CV joint grease into the bearing. Insert outer race over inner race then install retaining ring. To seat this boot properly into its housing or seal grooves on axle, secure these two boot clamps accordingly. Do not remove this outer CV joint from axle shaft. In order to replace the outer boot from here, remove the inner CV joint and boot. Cut off clamps then remove the outer boot from the axle shaft. Clean the outer CV joint assembly using solvent then check for wear and damage. If any components of a CV joint are excessively worn, replace the entire axle assembly. Use tape wrap around splines on shafts, insert new boots & clamps onto shafts. The outer CV joint needs to be repacked with new CV grease as well as spreading some grease inside the new boot. Place the outer boot on this CV joint then install new boot clamps. Reassemble the inner CV joint and boot as well as installing the driveaxle.
