How do I remove Brake Pad?

To remove all components except for Brembo brakes, start by removing the cap from the brake fluid reservoir. Then, loosen the wheel lug nuts and raise the vehicle, supporting it securely on jackstands. Remove the wheels and inspect the brake disc. Use a C-clamp to push the piston back into its bore, making sure the fluid in the master cylinder doesn't overflow. Rotate the caliper away from the disc and remove the outer brake pad, followed by the inner pad. Inspect and replace the support plates if necessary, and lubricate the contact areas on the mounting bracket. For installation, apply anti-squeal compound to the new brake pads and rotate the piston on rear calipers. Install the inner pad with the brake wear sensor positioned correctly, then install the new outer pad. Clean and lubricate the caliper guide pins before installing them, and tighten the guide pin bolts to the specified torque. After completing the job, depress the brake pedal to bring the pads into contact with the disc and check the brake fluid level and operation of the brakes before normal use. For removal with Brembo brake pads, follow the same initial steps of removing the cap, loosening lug nuts, raising the vehicle, and removing the wheels. Inspect the brake disc and then use a punch and hammer to remove the lower caliper guide pin and pad retainer. Remove the upper caliper guide pin and push the caliper pistons back into their bores. Finally, remove the pads from the caliper. To install the new pads, clean the caliper assembly and then reverse the removal steps. After completing the installation, depress the brake pedal to bring the new pads into contact with the disc, check the brake fluid level, and carefully test the brake operation before normal use.

Genuine Chevrolet Cobalt Brake Pad

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Brake Pads found

View related parts
Chevrolet Cobalt Pad Kit, Front Disc Brake
Part Number: 25808929
$170.20 MSRP: $337.69
You Save: $167.49 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chevrolet Cobalt | LEVEL 4 PERFORMANCE/SC (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 4 DOOR | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.4L
View related parts
Chevrolet Cobalt Pad Kit, Front Disc Brake
Part Number: 25809846
$35.47 MSRP: $66.93
You Save: $31.46 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Replaces: 15243704
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Cobalt | LEVEL THREE (SS) 2 DOOR, LEVEL THREE (SS) 4 DOOR | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.4L
View related parts
Chevrolet Cobalt Pad Kit, Front Disc Brake
Part Number: 10366667
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Replaces: 25906723
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2010 Chevrolet Cobalt | 2 DOOR, 4 DOOR, LEVEL 4 PERFORMANCE (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 2 DOOR, LEVEL ONE (LS) 2 DOOR, LEVEL ONE (LS) 4 DOOR, LEVEL THREE (SS) 2 DOOR, LEVEL THREE (SS) 4 DOOR, LEVEL TWO (LT) 2 DOOR, LEVEL TWO (LT) 4 DOOR | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.4L
View related parts
Chevrolet Cobalt Pad Kit,Rear Disc Brake
Part Number: 15271565
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Rear Pad
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chevrolet Cobalt | LEVEL 4 PERFORMANCE/SC (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 4 DOOR | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.4L
View related parts
Chevrolet Cobalt Pad Kit, Rear Disc Brake
Part Number: 10365723
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Rear Pad
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Cobalt | LEVEL 4 PERFORMANCE (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 2 DOOR, LEVEL THREE (SS) 2 DOOR, LEVEL THREE (SS) 4 DOOR | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.4L
View related parts
Chevrolet Cobalt Pad Kit, Front Disc Brake
Part Number: 20772243
Product Specifications
- Other Name: PAD KIT, Brake; Front Pad
- Position: Front
- Replaces: 20772242
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chevrolet Cobalt | LEVEL THREE (SS) 2 DOOR, LEVEL THREE (SS) 4 DOOR, LEVEL TWO (LT) 2 DOOR, LEVEL TWO (LT) 4 DOOR | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.4L
View related parts
Chevrolet Cobalt Pad Kit, Front Disc Brake
Part Number: 25894320
Product Specifications
- Other Name: PAD KIT, Brake; Brake Pad, Front Pad
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2007 Chevrolet Cobalt | LEVEL 4 PERFORMANCE (SS) 2 DOOR, LEVEL 4 PERFORMANCE/SC (SS) 2 DOOR | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.4L

Chevrolet Cobalt Brake Pad

Chevrolet Cobalt Brake Pad are crucial parts of the car's braking system that help the car to come to a halt by rubbing the rotating brake discs. These pads are metallic and synthetic in nature including copper, steel or aluminum alloy to have tolerance to heat since the pads mainly function through friction to transfer kinetic energy to thermal energy. Generally, there are two pads for every rotor and they are operated by a caliper that is located very close to it. Brakes have pads which get worn out and need replacement in certain period of time, and there are warning lights that signal the driver that is the time to replace them. It is essential to teach about the brake pads' variations named as non-metallic, semi-metallic, fully metallic, and ceramic are regarding friction material, wear, operation noise. This is why the brake pads should be maintained as frequently and as accurately as stated in the owners' manual to prevent things such as brake fade or more rotor wear.

Each OEM Chevrolet Cobalt Brake Pad we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Cobalt Brake Pad Parts Questions & Experts Answers

Pad Kit, Front Disc Brake
25808929
Q: How do I remove Brake Pad?
A: To remove all components except for Brembo brakes, start by removing the cap from the brake fluid reservoir. Then, loosen the wheel lug nuts and raise the vehicle, supporting it securely on jackstands. Remove the wheels and inspect the Brake Disc. Use a C-clamp to push the piston back into its bore, making sure the fluid in the master cylinder doesn't overflow. Rotate the caliper away from the disc and remove the outer brake pad, followed by the inner pad. Inspect and replace the support plates if necessary, and lubricate the contact areas on the mounting bracket. For installation, apply anti-squeal compound to the new brake pads and rotate the piston on rear calipers. Install the inner pad with the brake wear sensor positioned correctly, then install the new outer pad. Clean and lubricate the caliper guide pins before installing them, and tighten the guide pin bolts to the specified torque. After completing the job, depress the brake pedal to bring the pads into contact with the disc and check the brake fluid level and operation of the brakes before normal use. For removal with Brembo brake pads, follow the same initial steps of removing the cap, loosening lug nuts, raising the vehicle, and removing the wheels. Inspect the brake disc and then use a punch and hammer to remove the lower caliper guide pin and pad retainer. Remove the upper caliper guide pin and push the caliper pistons back into their bores. Finally, remove the pads from the caliper. To install the new pads, clean the caliper assembly and then reverse the removal steps. After completing the installation, depress the brake pedal to bring the new pads into contact with the disc, check the brake fluid level, and carefully test the brake operation before normal use.