How do you replace the door handle,Door Latch Assembly and Door Lock Cylinder on Chevrolet Camaro?

To gain access to the outside handle lever, the thumb turn cover plate has to be removed so that the retaining screw can be taken out. Third, remove the lock cylinder with trim bezel from inside the door as shown below photo. If at all possible, remove the outside door handle by pulling it out and towards the rear to break it from the handle reinforcement hole on the inside door. Check the outer door handles and the rubber seals around them and if they are worn or cracked replace them. Inside the door handle the door trim panel has to be taken out, the actuator cable has to be disconnected and then the handle had to be taken out. For the door latch or outside door handle reinforcement there is the following procedure to be followed Get the outside door handle lever off then get the door trim panel off. Unscrew the exterior retaining screw on the reinforcement of the outside door handle and then remove the reinforcement. Next, how to disconnect this assembly is by having removed latch mounting fasteners so that the complete assembly, which includes the latch and rods can be lowered after which the electrical connection can be disconnected and then finally pulling out this latch together with the rods. If not already done, the actuator rods can now be pulled off from the latch, by unscrewing the retaining clip on the latch and turning it till the lock rod detaches. Pull the cable connected to the inside door handle with the actuator and slid the latch off. Take the latch and outside door handle reinforcement and lay it on a clean working table and then remove the actuator rods from the latch or outside door handle reinforcement. For the door lock cylinder you have to open the door and then unlock the trim cap for the retaining screw by unscrewing it till it gets to the stop. Cock back the lock cylinder and the bezel and take off the gasket from the door. Release the lock cylinder bezel from lock cylinder and when replacing, put the gasket on the door, put the bezel on the lock cylinder and insert it in the outer part of the handle reinforcement. Otherwise, installation is practically the opposite of removal.

Genuine Chevrolet Camaro Door Handle

Inside Door Handle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Door Handles found

View related parts
Chevrolet Camaro Handle Kit, Front Side Door Outside
Part Number: 13521820
$72.34 MSRP: $108.15
You Save: $35.81 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle Kit, Front S/D O/S; Inside Handle, Outside Handle
- Position: Front
- Replaces: 13511135
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2024 Chevrolet Camaro | 2 DOOR CONVERTIBLE 1LS/1LT, 2 DOOR CONVERTIBLE 1LT, 2 DOOR CONVERTIBLE 1SS, 2 DOOR CONVERTIBLE 2LT, 2 DOOR CONVERTIBLE 2SS, 2 DOOR CONVERTIBLE HI PERFORMANCE, 2 DOOR CONVERTIBLE HIGH PERFORMANCE, 2 DOOR COUPE 1LS/1LT, 2 DOOR COUPE 1LT, 2 DOOR COUPE 1SS, 2 DOOR COUPE 2LT, 2 DOOR COUPE 2SS, 2 DOOR COUPE HI PERFORMANCE, 2 DOOR COUPE HIGH PERFORMANCE | 4 Cyl 2.0L, 6 Cyl 3.6L, 8 Cyl 6.2L
View related parts
Chevrolet Camaro Handle Assembly, Front Side Door Outside *Service Primer
Part Number: 92233089
$65.20 MSRP: $98.80
You Save: $33.60 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2015 Chevrolet Camaro | 2 DOOR CONVERTIBLE, 2 DOOR COUPE, LS 2 DOOR COUPE, LT 2 DOOR CONVERTIBLE, LT 2 DOOR COUPE, SS 2 DOOR CONVERTIBLE, SS 2 DOOR COUPE | 6 Cyl 3.6L, 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Camaro Handle Assembly, Front S/D I/S *Silver M
Part Number: 84602268
$21.60 MSRP: $32.16
You Save: $10.56 (33%)
ADD TO CART
Product Specifications
- Other Name: Inside Handle
- Position: Front
- Replaces: 84005971, 23366933
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2024 Chevrolet Camaro | 2 DOOR CONVERTIBLE 1LS/1LT, 2 DOOR CONVERTIBLE 1LT, 2 DOOR CONVERTIBLE 1SS, 2 DOOR CONVERTIBLE 2LT, 2 DOOR CONVERTIBLE 2SS, 2 DOOR CONVERTIBLE HI PERFORMANCE, 2 DOOR CONVERTIBLE HIGH PERFORMANCE, 2 DOOR COUPE 1LS/1LT, 2 DOOR COUPE 1LT, 2 DOOR COUPE 1SS, 2 DOOR COUPE 2LT, 2 DOOR COUPE 2SS, 2 DOOR COUPE HI PERFORMANCE, 2 DOOR COUPE HIGH PERFORMANCE | 4 Cyl 2.0L, 6 Cyl 3.6L, 8 Cyl 6.2L
View related parts
Chevrolet Camaro Handle Assembly, Aux R/Cmpt Lat Rel
Part Number: 84291438
$29.49 MSRP: $44.09
You Save: $14.60 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Emergency Handle
- Replaces: 23334425
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2024 Chevrolet Camaro | 2 DOOR CONVERTIBLE 1LS/1LT, 2 DOOR CONVERTIBLE 1LT, 2 DOOR CONVERTIBLE 1SS, 2 DOOR CONVERTIBLE 2LT, 2 DOOR CONVERTIBLE 2SS, 2 DOOR CONVERTIBLE HI PERFORMANCE, 2 DOOR CONVERTIBLE HIGH PERFORMANCE, 2 DOOR COUPE 1LS/1LT, 2 DOOR COUPE 1LT, 2 DOOR COUPE 1SS, 2 DOOR COUPE 2LT, 2 DOOR COUPE 2SS, 2 DOOR COUPE HI PERFORMANCE, 2 DOOR COUPE HIGH PERFORMANCE | 4 Cyl 2.0L, 6 Cyl 3.6L, 8 Cyl 6.2L
View related parts
Chevrolet Camaro Hdl Asm
Part Number: 20332647
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Handle, Outside Handle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1992 Chevrolet Camaro | 2 DOOR, 4 DOOR, RS 2 DOOR, RS CONVERTIBLE | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Hdl Asm
Part Number: 20332646
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Handle, Outside Handle
- Replaces: 20633580
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1992 Chevrolet Camaro | 2 DOOR, 4 DOOR, RS 2 DOOR, RS CONVERTIBLE | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Handle Assembly, Front S/D I/S *Silver M
Part Number: 84602267
$21.51 MSRP: $32.16
You Save: $10.65 (34%)
Product Specifications
- Other Name: Inside Handle
- Position: Front
- Replaces: 23366934, 84005969
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2024 Chevrolet Camaro | 2 DOOR CONVERTIBLE 1LS/1LT, 2 DOOR CONVERTIBLE 1LT, 2 DOOR CONVERTIBLE 1SS, 2 DOOR CONVERTIBLE 2LT, 2 DOOR CONVERTIBLE 2SS, 2 DOOR CONVERTIBLE HI PERFORMANCE, 2 DOOR CONVERTIBLE HIGH PERFORMANCE, 2 DOOR COUPE 1LS/1LT, 2 DOOR COUPE 1LT, 2 DOOR COUPE 1SS, 2 DOOR COUPE 2LT, 2 DOOR COUPE 2SS, 2 DOOR COUPE HI PERFORMANCE, 2 DOOR COUPE HIGH PERFORMANCE | 4 Cyl 2.0L, 6 Cyl 3.6L, 8 Cyl 6.2L
View related parts
Chevrolet Camaro Handle, Roof Lift Off Window Latch *Black
Part Number: 20255908
Product Specifications
- Other Name: HANDLE, Roof Panel; Handle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1992 Chevrolet Camaro | 2 DOOR, 4 DOOR, RS 2 DOOR, RS CONVERTIBLE | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Handle, Roof Lift Off Window Latch *Black
Part Number: 20255909
Product Specifications
- Other Name: HANDLE, Roof Panel; Handle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1992 Chevrolet Camaro | 2 DOOR, 4 DOOR, RS 2 DOOR, RS CONVERTIBLE | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 8 Cyl 5.0L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Handle Assembly, Front Side Door Inside * Black
Part Number: 16628402
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-2002 Chevrolet Camaro | 2 DOOR, CONVERTIBLE | 6 Cyl 3.4L, 6 Cyl 3.8L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Handle Assembly, Front Side Door Inside *Black
Part Number: 16628403
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-2002 Chevrolet Camaro | 2 DOOR, CONVERTIBLE | 6 Cyl 3.4L, 6 Cyl 3.8L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Handle Assembly, Front Side Door Outside *Paint To Mat
Part Number: 16628414
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front
- Replaces: 10287430, 10296258, 10287432, 10287438, 10297585, 10287428, 10296254
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-2002 Chevrolet Camaro | 2 DOOR, CONVERTIBLE | 6 Cyl 3.4L, 6 Cyl 3.8L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Handle Assembly, Front Side Door Outside *Paint To Mat
Part Number: 16628415
Product Specifications
- Other Name: HANDLE, Door Outside Handle; Outside Handle
- Position: Front
- Replaces: 10297586, 10287437, 10287433, 10297457, 10287439, 10296259, 10287425, 10287429, 10287431, 10296255
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-2002 Chevrolet Camaro | 2 DOOR, CONVERTIBLE | 6 Cyl 3.4L, 6 Cyl 3.8L, 8 Cyl 5.7L
View related parts
Chevrolet Camaro Hdl Assembly, Front Door Lock Remote Control
Part Number: 20220728
Product Specifications
- Other Name: HANDLE, Door Lock Inside Handle; Inside Handle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1992 Chevrolet Camaro | 2 DOOR, 4 DOOR, RS 2 DOOR, RS CONVERTIBLE | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.1L, 8 Cyl 5.0L, 8 Cyl 5.7L

Chevrolet Camaro Door Handle

One of the important role of the Interior Door Handle of Chevrolet Camaro car model is the ability to unlock the door and facilitate the exit of the car. This a small handle works in the same way as the external handle: it only unscrews the hook of the door from the latch. The Chevrolet Camaro's Interior Door Handle can wear out over a certain period, and probably due to frequent use of the driver's side handle would get some scratches and therefore bring some decline on the interior appearance of the Camaro. There are many interior door handles that have been used on different years of the Chevrolet Camaro and while certain differences are not described in detail. Regardless of the style, the primary mechanism remains consistent: a bar which unlocks the door latch assembly. If there is a problem on the Interior Door Handle or the latch assembly, it will result in operational problems, which is why it is crucial that this part should be preserved for the efficiency of the Chevrolet Camaro.

Each OEM Chevrolet Camaro Door Handle we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Camaro Door Handle Parts Questions & Experts Answers

Handle Assembly, Front Side Door Outside *Service Primer
92233089
Q: How do you replace the door handle,Door Latch Assembly and Door Lock Cylinder on Chevrolet Camaro?
A: To gain access to the outside handle lever, the thumb turn cover plate has to be removed so that the retaining screw can be taken out. Third, remove the lock cylinder with trim bezel from inside the door as shown below photo. If at all possible, remove the outside door handle by pulling it out and towards the rear to break it from the handle reinforcement hole on the inside door. Check the outer door handles and the rubber seals around them and if they are worn or cracked replace them. Inside the door handle the door trim panel has to be taken out, the actuator cable has to be disconnected and then the handle had to be taken out. For the door latch or outside door handle reinforcement there is the following procedure to be followed Get the outside door handle lever off then get the door trim panel off. Unscrew the exterior retaining screw on the reinforcement of the outside door handle and then remove the reinforcement. Next, how to disconnect this assembly is by having removed latch mounting fasteners so that the complete assembly, which includes the latch and rods can be lowered after which the electrical connection can be disconnected and then finally pulling out this latch together with the rods. If not already done, the actuator rods can now be pulled off from the latch, by unscrewing the retaining clip on the latch and turning it till the lock rod detaches. Pull the cable connected to the inside door handle with the actuator and slid the latch off. Take the latch and outside door handle reinforcement and lay it on a clean working table and then remove the actuator rods from the latch or outside door handle reinforcement. For the door lock cylinder you have to open the door and then unlock the trim cap for the retaining screw by unscrewing it till it gets to the stop. Cock back the lock cylinder and the bezel and take off the gasket from the door. Release the lock cylinder bezel from lock cylinder and when replacing, put the gasket on the door, put the bezel on the lock cylinder and insert it in the outer part of the handle reinforcement. Otherwise, installation is practically the opposite of removal.