How to check and replace the knock sensor and Ignition Control Module for Chevrolet C1500 and K1500?

The knock sensor is liable for sensing irregular engine vibrations and minimizing spark knock. This results in a greater degree of AC output voltage, which is then given to ECM/PCM to retard the timing. Depending on the year and engine application, the location of this sensor can be different but normally it is found at the rear of the engine block or even at the side of cylinder head. For checking resistance of this sensor, remove electric connector and measure resistance between terminal and vital part of engine's body. If it falls outside this range, it should therefore be replaced. While running engine again, connect back connector and use voltmeter to verify an AC voltage signal here. Voltage ought to rise with increase in speed of an engine. If there is no any voltage signal available then knock sensor must be replaced because it has failed completely. When replacing this knock sensor just disconnect negative battery terminal before removing distributor or oil pressure sending unit if necessary; disconnect electrical connector and remove knocker from your engine block; installation is opposite to removal process. On 1988 -1995 models, ESC module located near throttle body however starting 1996 up to 2000 model years incorporated Knock Sensor Module with PCM as stated above; therefore remove PCM along with Knock Sensor Module cover also take out Knock Sensor by pinching retaining tabs & pulling up vertically straight; align tabs on notches press down until retaining clips snap into place for installing Knock Sensor Module while finally install PCM cover as well as Knock Sensor Module cover too.

Genuine Chevrolet C1500 Knock Sensor

Engine Knock Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Knock Sensors found

View related parts
Chevrolet C1500 Sensor,Knock
Part Number: 10456288
$44.79 MSRP: $93.01
You Save: $48.22 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); ESC Sensor, Knock Sensor
- Replaces: 10456018
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1999 Chevrolet C1500 | C1500 EXTENDED CAB LONG BOX, C1500 EXTENDED CAB STANDARD BOX, C1500 REGULAR CAB LONG BOX, C1500 REGULAR CAB STANDARD BOX | 6 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L Diesel, 8 Cyl 7.4L
View related parts
Chevrolet C1500 Sensor,Knock
Part Number: 10456549
$35.57 MSRP: $114.39
You Save: $78.82 (69%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); ESC Sensor, Knock Sensor
- Replaces: 10456031
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1995 Chevrolet C1500 | C1500 EXTENDED CAB LONG BOX, C1500 EXTENDED CAB STANDARD BOX, C1500 REGULAR CAB LONG BOX, C1500 REGULAR CAB STANDARD BOX | 6 Cyl 4.3L, 8 Cyl 5.7L, 8 Cyl 7.4L
View related parts
Chevrolet C1500 Sensor,Knock
Part Number: 10456146
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); ESC Sensor, Knock Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Chevrolet C1500 | C1500 EXTENDED CAB LONG BOX, C1500 EXTENDED CAB STANDARD BOX, C1500 REGULAR CAB LONG BOX, C1500 REGULAR CAB STANDARD BOX | 6 Cyl 4.3L
View related parts
Chevrolet C1500 Sensor,Knock
Part Number: 10456287
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Control Module, ESC Sensor, Knock Sensor, Sensor
- Replaces: 10456017
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1999 Chevrolet C1500 | C1500 EXTENDED CAB LONG BOX, C1500 EXTENDED CAB STANDARD BOX, C1500 REGULAR CAB LONG BOX, C1500 REGULAR CAB STANDARD BOX | 6 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 6.2L Diesel, 8 Cyl 7.4L
View related parts
Chevrolet C1500 Knock, Sensor O/L
Part Number: 10456019
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Knock Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1995 Chevrolet C1500 | C1500 EXTENDED CAB LONG BOX, C1500 EXTENDED CAB STANDARD BOX, C1500 REGULAR CAB LONG BOX, C1500 REGULAR CAB STANDARD BOX | 8 Cyl 5.0L
View related parts
Chevrolet C1500 Sensor,Knock
Part Number: 10456082
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); ESC Sensor, Knock Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Chevrolet C1500 | C1500 EXTENDED CAB LONG BOX, C1500 EXTENDED CAB STANDARD BOX, C1500 REGULAR CAB LONG BOX, C1500 REGULAR CAB STANDARD BOX | 6 Cyl 4.3L
View related parts
Chevrolet C1500 Sensor,Knock
Part Number: 10456075
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Knock Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1998 Chevrolet C1500 | C1500 EXTENDED CAB LONG BOX, C1500 EXTENDED CAB STANDARD BOX, C1500 REGULAR CAB LONG BOX, C1500 REGULAR CAB STANDARD BOX | 6 Cyl 4.3L

Chevrolet C1500 Knock Sensor

Chevrolet C1500 cars have the Knock Sensor that is responsible for the detection of the knock and send a signal to the power train control which in turn adjusts the ignition timing accordingly. Usually piezoelectric, the sensor measures vibrations and translates them into electrics signals to record pressure spikes, described as knock. This is possible because ignition timing can be precisely adjusted to enhance performance, while at the same time eliminating possibility of damage to the engine. Some of the contemporary systems can even control timings for each cylinder and boost pressure to achieve the premier efficiency and durability in various modes. Chevrolet C1500 Knock Sensor is an important component that assists in proper running of the engine and preventing any mishaps.

Each OEM Chevrolet C1500 Knock Sensor we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet C1500 Knock Sensor Parts Questions & Experts Answers

Sensor,Knock
10456549
Q: How to check and replace the knock sensor and Ignition Control Module for Chevrolet C1500 and K1500?
A: The knock sensor is liable for sensing irregular engine vibrations and minimizing spark knock. This results in a greater degree of AC output voltage, which is then given to ECM/PCM to retard the timing. Depending on the year and engine application, the location of this sensor can be different but normally it is found at the rear of the engine block or even at the side of cylinder head. For checking resistance of this sensor, remove electric connector and measure resistance between terminal and vital part of engine's body. If it falls outside this range, it should therefore be replaced. While running engine again, connect back connector and use voltmeter to verify an AC voltage signal here. Voltage ought to rise with increase in speed of an engine. If there is no any voltage signal available then knock sensor must be replaced because it has failed completely. When replacing this knock sensor just disconnect negative battery terminal before removing distributor or oil pressure sending unit if necessary; disconnect electrical connector and remove knocker from your engine block; installation is opposite to removal process. On 1988 -1995 models, ESC module located near throttle body however starting 1996 up to 2000 model years incorporated Knock Sensor Module with PCM as stated above; therefore remove PCM along with Knock Sensor Module cover also take out Knock Sensor by pinching retaining tabs & pulling up vertically straight; align tabs on notches press down until retaining clips snap into place for installing Knock Sensor Module while finally install PCM cover as well as Knock Sensor Module cover too.