My Garage
My Account
Cart
Genuine Chevrolet C1500 Idler Arm
Steering Idler Arm- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Idler Arms found
Chevrolet C1500 Arm Kit,Steering Linkage Idler
Part Number: 26016461$115.52 MSRP: $185.17You Save: $69.65 (38%)
Chevrolet C1500 Idler Arm
The Idler Arm in Chevrolet C1500 vehicles is an important part of vehicle steering mechanism specifically being the pivotal support to the center link on the side of vehicle frame towards the passenger's side. The Idler Arm, which works in conjunction with the Pitman arm, is used to hold the center link at the correct height so that the correct steering alignment is maintained on the system. As much as it plays a centralized role in the functioning of the vehicle, the Idler Arm can easily wear out; thus, it requires more frequent servicing where greasing is done using a grease gun when changing the oil. Maintenance of the Idler Arm also improves the steadiness of the steering as well as the lifespan of the Chevrolet C1500 steering linkage system.
Each OEM Chevrolet C1500 Idler Arm we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Chevrolet C1500 Idler Arm Parts Questions & Experts Answers
- Q: How to inspect and replace Center Link,Idler Arm,Pitman Arm and Tie Rod?A: To make sure that the front wheels maintain their alignment, you use a steering linkage to connect the steering gear with them. It encompasses various constituents like the Pitman arm, idler arm, relay rod, tie-rods and steering damper. The Pitman arm moves to and fro on the relay rod from its attachment on the steering gear shaft. On the other end is where the relay rod is supported by an idler arm. The tie-rod assemblies transmit this motion of the relay rod to the steering knuckles. For inspection of steering system: set wheels straight ahead and lock steering wheel; jack up one side of vehicle and attach dial indicator to measure any play in system; if it exceeds specified limit inspect for loosened or damaged components which need replacement; also observe torn ball stud boots, frozen joints & bent or damaged linkage components. To remove and install a tie-rod loosen wheel lug nuts, jack up vehicle then remove wheel, separate tie-rod end from steering knuckle using two-jaw puller, remove nut holding inner tie-rod end to relay rod itself but before unscrewing it measure distance and record it-if part needs replacement lubricate new tie-rod end and adjust it according to recorded dimension-connect outer tie-rod end to steering knuckle again tightening nut used before while inserting new cotter pin-insert inner tie-rod end into relay rod tighten nut holding it there lastly tighten clamp nuts then lower car down again. For removing idler arm loose nut then pry 2-jaw puller apart this will disengage it from relay rod-after taking out idler arm to frame bolts carefully install another one tightening bolts completely-take idler arm ball stud and fix it securely within relay rod by tightening its respective nut till just about hand tightness becomes possible then go ahead with complete application of force originating torque wrench on said fastener as much as required ensuring that nut is tightened to specified torque Installation is the reverse of removal, ensuring the nuts are tightened to the specified torque. Remove Pitman arm from relay rod using puller. Before reassembling, mark Pitman arm and steering gear shaft for proper alignment during installation. Take out Pitman arm nut and washer followed by removing entire thing with a help of a puller. Look at threads on ball stud along with any sealants sealing them again wipe down thread well.
