My Garage
My Account
Cart
Genuine Chevrolet Blazer Timing Chain
Engine Timing Chain- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
13 Timing Chains found
Chevrolet Blazer Chain Assembly, Balancer
Part Number: 12626983$31.99 MSRP: $52.95You Save: $20.96 (40%)Ships in 1-2 Business Days
Chevrolet Blazer Chain, Camshaft Timing
Part Number: 14088783$76.15 MSRP: $126.04You Save: $49.89 (40%)Ships in 1-2 Business Days
Chevrolet Blazer Chain Assembly, Timing
Part Number: 12627107$66.52 MSRP: $104.60You Save: $38.08 (37%)Ships in 1-2 Business Days
Chevrolet Blazer Chain Kit,Timing (W/Sprockets)
Part Number: 12458911$51.96 MSRP: $81.77You Save: $29.81 (37%)
Chevrolet Blazer Chain,Camshaft Timing
Part Number: 14087014$56.22 MSRP: $88.46You Save: $32.24 (37%)Ships in 1-2 Business Days
Chevrolet Blazer Chain Assembly, Timing
Part Number: 12647895$48.69 MSRP: $80.55You Save: $31.86 (40%)Ships in 1-2 Business Days
Chevrolet Blazer Chain Assembly, Tmg
Part Number: 55514729$13.73 MSRP: $21.61You Save: $7.88 (37%)Ships in 1-3 Business Days
Chevrolet Blazer Chain Assembly, Tmg
Part Number: 12694716$37.08 MSRP: $58.36You Save: $21.28 (37%)Ships in 1-3 Business Days
Chevrolet Blazer Chain,Camshaft Timing
Part Number: 10128485$41.00 MSRP: $64.53You Save: $23.53 (37%)Ships in 1-3 Business Days
Chevrolet Blazer Chain Assembly, Timing
Part Number: 14022647$86.08 MSRP: $135.44You Save: $49.36 (37%)Chevrolet Blazer Chain Assembly, Balr
Part Number: 55516894$4.54 MSRP: $7.13You Save: $2.59 (37%)Ships in 1-3 Business DaysChevrolet Blazer CHAIN ASM-BALR
Part Number: 12719738$19.81 MSRP: $31.17You Save: $11.36 (37%)Ships in 1-3 Business Days
Chevrolet Blazer Chain Assembly, Timing
Part Number: 14103224$17.84 MSRP: $28.07You Save: $10.23 (37%)
Chevrolet Blazer Timing Chain
The Timing Chain in Chevrolet Blazer vehicles is used to maintain the proper relationship of the rotations of the camshaft and the crankshaft in order to have consistent valve timing meant to assist in performance of the engine. Sitting in the front of the engine, this metal chain needs some kind of lubrication to work and is predominantly in higher displacement engines. Metal timing chains have also gained popularity since the early 1990s over the rubber timing belts concerning their strength and less required replacement. Despite this, timing chains are quite durable and the problems that can arise are as a result of lubrication failure or issues with the tensioner and the chain guides and the signs are usually a rattle emanating from the engine. Pushrod engines use a short chain drive since it offers low noise and wear arising from torque reversals than the use of gear drives.
Each OEM Chevrolet Blazer Timing Chain we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Chevrolet Blazer Timing Chain Parts Questions & Experts Answers
- Q: How to remove and install the timing chain cover,Timing Chain and Sprocket on 4.3L V6 engine on Chevrolet Blazer?A: Disconnecting the negative battery cable is the first step in removal and installation of the Timing Cover. To remove, you will have to remove upper and lower fan shrouds, drive belt, cooling fan and water pump. The number four piston must be positioned at TDC on the compression stroke, then remove the drive belt pulley and crankshaft damper. If applicable, don't forget to take out the crankshaft position sensor and wiring harness nut. Loosen front Oil Pan nuts before removing cover bolts when separating Timing Cover from block and breaking gasket seal if necessary. Note that for some engines, the front cover may be made of composite material and should be replaced rather than resealed. Just inside the front cover, pull off crankshaft position sensor reluctor ring which is attached to a camshaft sprocket and chain assembly. For an old gasket material use a gasket scraper to scrape it off; cleaning lacquer thinner or acetone should be wiped over sealing surfaces of engine cover and block; inspecting flange condition of a cover is recommended. Make sure that when installing a Woodruff key line up coincides with both crankshaft sprocket's as well as balance shaft gears'. Use clean engine oil to lubricate the chain; put Loctite on camshaft sprocket bolt threads before installing them tightly or tighten them after installing using Loctite. Apply RTV sealant in U-shaped channel on bottom side of the cover check oil pan-to-block joints; also check whether there are any leaks between housing halves in place where they meet with each other in front of timing chain area that is why you need to apply RTV sealant between them too. Thin layer of RTV sealant should be spread over both sides of new gasket so that it can be positioned on engine block by dowel pins thus holding it firmly in place. Finally install Timing Cover and tighten bolts taking into account whether it is necessary to remove or pry down oil pan for access. Lastly, apply moly-base grease or clean engine oil onto the vibration damper hub's oil seal contact surface, put the damper on the crankshaft, and proceed with other remaining installation steps including using new O-ring for crankshaft position sensor.
- Q: How do I remove and install the timing chain cover,Timing Chain and Sprocket on 2.2L four cylinder engine on Chevrolet Blazer?A: Begin by removing the cover, then isolate it from the negative battery cable. After that, remove fan shroud upper part, drive belt, fan/clutch assembly, water pump pulley, crankshaft pulley and hub. Remove the drive belt tensioner bracket and Timing Cover-to-engine block bolts next. Utilize a gasket scraper to erase any old gasket material and clean any of the sealing surfaces. To remove the timing chain; temporarily install crankshaft pulley hub and bolt; rotate crankshaft to align timing marks on crankshaft and camshaft sprockets; push back timing chain tensioner plunger and insert pin to retain plunger; using prybar holding engine while removing camshaft bolt; carefully prying camshaft sprocket off. Check for damage or wearout on timing chain and sprockets before replacing if necessary. Mesh new timing chains with camshafts; put them into engagement with crankshafts at their sprocket's teeth; aligning timing marks; installing tightening camshaft sprocket bolt; releasing tensioner; lubricating chain/sprocket; rotating engine to check alignment of timing marks; applying RTV sealant to oil pan sealing surface; finally securing front cover using new rubber seal.
Related Chevrolet Blazer Parts
Browse by Year
2024 Timing Chain 2023 Timing Chain 2022 Timing Chain 2021 Timing Chain 2020 Timing Chain 2019 Timing Chain 2005 Timing Chain 2004 Timing Chain 2003 Timing Chain 2002 Timing Chain 2001 Timing Chain 2000 Timing Chain 1999 Timing Chain 1998 Timing Chain 1997 Timing Chain 1996 Timing Chain 1995 Timing Chain 1994 Timing Chain 1993 Timing Chain 1992 Timing Chain 1991 Timing Chain 1990 Timing Chain 1989 Timing Chain 1988 Timing Chain 1987 Timing Chain 1986 Timing Chain 1985 Timing Chain