How do you replace the Electronic Control Module and ensure proper installation of the MEM-CAL on Chevrolet Beretta?

To remove or install the Electronic Control Module make sure that the ignition switch is off and do not connect or disconnect any connectors when it is on. The ECM is fixed beneath the instrument panel. Start with the removal of the negative terminal of the battery being careful to disable the locking of the blade connector on models with the Delco Loe II audio system. Pull off the glove box to reach the ECM and then remove the retaining bolts to ease out the ECM with the assistance of fingers to disconnected the electrical connectors. For MEM-CAL replacement wherein one MEM-CAL can be utilized for multiple vehicles, the MEM-CAL is embedded in the ECM and carries vehicle data. When changing MEM-CAL one has to make sure to have a correct number for an MEM-CAL as when you get an ECM from a dealer than it does not come with MEM-CAL. Locate and take off the MEM-CAL access cover After exercising this step, the retaining clips should be put back while pulling out the MEM- CAL off socket without causing damage. Ensure that the numbers appearing on the earlier and the newer ECMs or MEM-CALs tally. To install the new MEM-CAL, press only on the ends and when the notches are to the socket, the clips will engage. After installation, check for right seating position by starting the ignition then putting the diagnostic mode and looking at the message code then look for Code 12 that shows that no other codes are present. When trouble codes come up or the light illuminates, the switch should be in its correct position if the MEM-CAL is not defective.

Genuine Chevrolet Beretta Engine Control Module

Engine Control Computer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Engine Control Modules found

View related parts
Chevrolet Beretta Engine Control Module Assembly(Remanufacture)
Part Number: 88999170
$74.38 MSRP: $213.26
You Save: $138.88 (66%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Asm,Engine Control (Remanufacture) ; Module, Emission Control System; Control Module, ECM, EEC Module
- Replaces: 01227748, 1227748
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 Chevrolet Beretta | 2 DOOR, 4 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 4 Cyl 2.2L
View related parts
Chevrolet Beretta Powertrain Control Module (Remanufacture)
Part Number: 16215830
$138.40 MSRP: $261.14
You Save: $122.74 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module,Powertrain Control(Remanufacture); Control Module, ECM, EEC Module, PCM, Radio
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet Beretta | 2 DOOR, 4 DOOR, Z26 2 DOOR | 4 Cyl 2.2L
View related parts
Chevrolet Beretta Powertrain Control Module Assembly (Remanufacture)
Part Number: 88961137
$66.54 MSRP: $187.73
You Save: $121.19 (65%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Asm,Powertrain Control (Remanufacture) ; Module, Emission Control System; Control Module, ECM
- Replaces: 16183978, 16173278
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Chevrolet Beretta | 2 DOOR, 4 DOOR | 4 Cyl 2.3L
View related parts
Chevrolet Beretta Engine Control Module Assembly(Remanufacture)
Part Number: 88963804
$71.73 MSRP: $203.04
You Save: $131.31 (65%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Asm,Engine Control (Remanufacture) ; Module, Emission Control System; Control Module, ECM, EEC Module
- Replaces: 16191947
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Chevrolet Beretta | 2 DOOR, 4 DOOR, Z26 2 DOOR | 4 Cyl 2.2L, 4 Cyl 2.3L
View related parts
Chevrolet Beretta Prom Pkg, Ecm
Part Number: 16158354
$66.80 MSRP: $142.27
You Save: $75.47 (54%)
ADD TO CART
Product Specifications
- Other Name: EPROM, Emission Control System
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 Chevrolet Beretta | 2 DOOR, 4 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 4 Cyl 2.2L
View related parts
Chevrolet Beretta Engine Control Module Assembly(Remanufacture)
Part Number: 88999181
$103.40 MSRP: $192.42
You Save: $89.02 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Asm,Engine Control (Remanufacture) ; Module, Emission Control System; Control Module, ECM
- Replaces: 16156450
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 Chevrolet Beretta | 2 DOOR, 4 DOOR | 4 Cyl 2.3L
View related parts
Chevrolet Beretta Engine Control Module Assembly(Remanufacture)
Part Number: 88999173
$116.58 MSRP: $218.18
You Save: $101.60 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Asm,Engine Control (Remanufacture) ; Module, Emission Control System; ECM
- Replaces: 01228321, 1228321
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1989 Chevrolet Beretta | 2 DOOR, 4 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 4 Cyl 2.0L
View related parts
Chevrolet Beretta Engine Control Module (Remanufacture)
Part Number: 88999196
$136.20 MSRP: $253.43
You Save: $117.23 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module,Engine Control(Remanufacture); Control Module, Controller, ECM
- Replaces: 16198262
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1993 Chevrolet Beretta | 2 DOOR, 4 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 4 Cyl 2.0L, 6 Cyl 2.8L, 6 Cyl 3.1L
View related parts
Chevrolet Beretta Powertrain Control Module Assembly (Remanufacture) Requires Reprogramming
Part Number: 88963800
$142.68 MSRP: $257.01
You Save: $114.33 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Asm,Powertrain Control (Remanufacture) Requires Reprogramming ; Module, Emission Control System
- Replaces: 16211539
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet Beretta | 2 DOOR, 4 DOOR, Z26 2 DOOR | 6 Cyl 3.1L
View related parts
Chevrolet Beretta Engine Control Module Assembly(Remanufacture) Requires Reprogramming
Part Number: 88999204
$145.31 MSRP: $268.83
You Save: $123.52 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Asm,Engine Control (Remanufacture) Requires Reprogramming ; Module, Emission Control System; Control Module, ECM, EEC Module
- Replaces: 16188606, 16134847
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Chevrolet Beretta | 2 DOOR, 4 DOOR | 4 Cyl 2.2L
View related parts
Chevrolet Beretta EPROM, Emission Control System
Part Number: 16166786
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 Chevrolet Beretta | 2 DOOR, 4 DOOR | 4 Cyl 2.3L
View related parts
Chevrolet Beretta EPROM, Emission Control System
Part Number: 16172116
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Chevrolet Beretta | 2 DOOR, 4 DOOR | 4 Cyl 2.3L
View related parts
Chevrolet Beretta EPROM, Emission Control System
Part Number: 16190180
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990 Chevrolet Beretta | 2 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 6 Cyl 3.1L
View related parts
Chevrolet Beretta Calibrator,Integrated Circuit Connect(9601Ascx)
Part Number: 16149600
Product Specifications
- Other Name: EPROM, Emission Control System
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Chevrolet Beretta | 2 DOOR, 4 DOOR | 4 Cyl 2.3L
View related parts
Chevrolet Beretta Eprom Pkg, Ecm
Part Number: 16178176
Product Specifications
- Other Name: EPROM, Emission Control System
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990 Chevrolet Beretta | 2 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 6 Cyl 3.1L
View related parts
Chevrolet Beretta Eprom Asm,Ecm
Part Number: 16190174
Product Specifications
- Other Name: EPROM, Emission Control System
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Chevrolet Beretta | 2 DOOR, 4 DOOR | 6 Cyl 3.1L
View related parts
Chevrolet Beretta Calibration Unit,Integrated Circuit Connect(3649Anfu)
Part Number: 16133648
Product Specifications
- Other Name: EPROM, Emission Control System
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990 Chevrolet Beretta | 2 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 4 Cyl 2.3L
View related parts
Chevrolet Beretta Eprom,Ecm
Part Number: 16190177
Product Specifications
- Other Name: EPROM, Emission Control System
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990 Chevrolet Beretta | 2 DOOR, 4 DOOR NOTCHBACK, 4 DOOR PLAIN BACK HATCHBACK, LTZ | 6 Cyl 3.1L
View related parts
Chevrolet Beretta Eprom Asm,Ecm
Part Number: 16193199
Product Specifications
- Other Name: EPROM, Emission Control System
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chevrolet Beretta | 2 DOOR, 4 DOOR | 6 Cyl 3.1L

Chevrolet Beretta Engine Control Module

Chevrolet Beretta auto uses Engine Control Module or ECM as an electronic control module that is in charge of engine operation. It receives information from all sorts of sensors including oxygen sensor, throttle position sensor among others and sustain the perfect proportion of air-fuel mixture, idle speed and other operational essentials. As a result of controlling fuel delivery and turning on ignition coils, the Chevrolet Beretta ECM provides precise operation of the engine. Electronically controlled manual transmissions have also been applied in Chevrolet Beretta models and these have included various circuit types such as the integrated circuit and advanced microprocessor circuit. These new ECMs can govern other features like the variable valve timing and transmission control thus improving vehicle efficiency. While purchasing Chevrolet Beretta Engine Control Module, there are options of new or rebuilt units, but one has to ensure that they get compatible parts for the system.

Each OEM Chevrolet Beretta Engine Control Module we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Beretta Engine Control Module Parts Questions & Experts Answers

Engine Control Module Assembly(Remanufacture)
88963804
Q: How do you replace the Electronic Control Module and ensure proper installation of the MEM-CAL on Chevrolet Beretta?
A: To remove or install the Electronic Control Module make sure that the ignition switch is off and do not connect or disconnect any connectors when it is on. The ECM is fixed beneath the instrument panel. Start with the removal of the negative terminal of the battery being careful to disable the locking of the blade connector on models with the Delco Loe II audio system. Pull off the glove box to reach the ECM and then remove the retaining bolts to ease out the ECM with the assistance of fingers to disconnected the electrical connectors. For MEM-CAL replacement wherein one MEM-CAL can be utilized for multiple vehicles, the MEM-CAL is embedded in the ECM and carries vehicle data. When changing MEM-CAL one has to make sure to have a correct number for an MEM-CAL as when you get an ECM from a dealer than it does not come with MEM-CAL. Locate and take off the MEM-CAL access cover After exercising this step, the retaining clips should be put back while pulling out the MEM- CAL off socket without causing damage. Ensure that the numbers appearing on the earlier and the newer ECMs or MEM-CALs tally. To install the new MEM-CAL, press only on the ends and when the notches are to the socket, the clips will engage. After installation, check for right seating position by starting the ignition then putting the diagnostic mode and looking at the message code then look for Code 12 that shows that no other codes are present. When trouble codes come up or the light illuminates, the switch should be in its correct position if the MEM-CAL is not defective.

Related Chevrolet Beretta Parts

Browse by Year

1996 Engine Control Module 1995 Engine Control Module 1994 Engine Control Module 1993 Engine Control Module 1992 Engine Control Module 1991 Engine Control Module 1990 Engine Control Module 1989 Engine Control Module 1988 Engine Control Module 1987 Engine Control Module