My Garage
My Account
Cart
Genuine Cadillac Fleetwood Wiper Arm
Windshield Wiper Arm- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
21 Wiper Arms found
Cadillac Fleetwood Arm Assembly, Windshield Wiper *Black
Part Number: 25646217$18.18 MSRP: $45.20You Save: $27.02 (60%)Ships in 1-2 Business Days
Cadillac Fleetwood Insert, Windshield Wiper Blade
Part Number: 12339129$4.85 MSRP: $7.92You Save: $3.07 (39%)Ships in 1-2 Business Days
| Page 1 of 2 |Next >
1-20 of 21 Results
Cadillac Fleetwood Wiper Arm Parts Questions & Experts Answers
- Q: How to remove and install wiper arms and Wiper Blade in Cadillac ElDorado and Fleetwood?A: To remove and install wiper arms in Cadillac DeVille and Fleetwood vehicles, raise the hood for access. Run the wipers until they are midway on the windshield, then turn off the ignition. Remove the wiper arm from the windshield. For 1990 cars, pull the retaining latch and take off the arm from transmission shaft. Use a proper tool to disengage the retaining latch and separate from transmission shaft for 1991-up vehicles. To install, put back the wiper arm on top of transmission shaft after pushing it in through the retaining latch and then return it into position on the windshield. If an adjustment is needed, follow these steps:Take away right-hand wiper arm.Open up small door to get to wiper linkage.Loosen but not remove transmission linkage adjustment nuts.Rotate left arm-blade assembly just below blade stops.Tighten transmission adjustment screws to 64 inch lbs for 1990 vehicles only; orTighten trans-mission linkage adjustment nuts to 44 inch lbs for 1991 cars; orTighten trans-mission linkage adjustment nuts to 71 inch lbs for 1992-up vehicles;Position right wiper arm and blade assembly below blade stops, then assemble onto transmission shaft again; and finally Lift both arm and blade assemblies over stops. Test the wiping pattern with a wet windshield at low speed operation of the wipers. On Eldorado & Seville early models, operate the wipers until they are mid-way through their travel cycle before turning off ignition switch. Remove hose on wiper arm from hose connector by lifting up on outer ring of one-piece connector while holding stationary inner part of connector that connects to hose fitting located at end of extendable nozzle reaching toward body opening side away from hood hinge area below base portion having telescoping handle formed thereon at one end of said hollow wiper arm adapted connect other side an automobile windshield wipers which are activated by turning switch near steering wheel inside passenger compartment. Lift wiper arm from the windshield by pulling up and then moving it away from the windshield to disengage retaining latch. Remove arm from transmission shaft. To install, slide arm over transmission shaft, push on retaining latch then return to initial place on windshield. Now attach hose on wiper arm to hose connector again. In case an adjustment is necessary, lift the hood and remove the wiper arms. Open the cowl vent screen, left side, transmission adjustment window. Loosen the screws attaching the transmission drive link-to-motor crank arm and move both parts as one against each other until they engage so that they can hold together when put back onto a motor shaft alone without any other element in between them except for bearing surface(s) of linkage points with moving cylindrical members thereof that serve purpose maintaining connection between these two components during rotation about axis parallel thereto without providing any relative movement relative to one another along this line while being restrained against axial displacement due to frictional contact at such areas where those surfaces come into contact during such rotation; align slot keyway push down engage slide latch tighten attaching screw 4 ft lbs still below ramp stop while keeping located near bottom window sufficiently away edge thereabove allow room clearance when installing rearwardly extending said means for holding vehicle has been driven forward into position where its tailgate can be closed securely because it would otherwise interfere operationally closing thereof; position right blade assembly approximately inch below turn latches close adjustment windows then place arms ramps shown figure above tightening pull down again making sure firmly seated top or bottom holes because if not properly tightened leakage may occur leading corrosion internal damage associated with presence liquid contaminants drive gear train due higher pressure being exerted upon same than what actually required prevent passage fluids there through causing them all drips always follow specifications provided respective vehicle manufacturer whenever performing particular maintenance procedure; such as adjusting motor condition engine running; checking freeplay bearings; replacing spark plugs etc. According to the prompt, this is done if adjustment is necessary. The wipers must be turned off while they are in mid-wipe position. Lift the wiper arm up and remove it from the windshield by pulling on it until the retaining latch disengages. Take off your transmission shaft by removing your arm. Finally, just put your arm back onto it and push down the latch sticking on windshield. Attach a hose to a wiper arm in a hose connector again. When making an adjustment, open the hood and remove all of the windshield wipers. Open up the cowl vent screen by pressing on the left side and then close this window after loosening screws which attach motor's drive mechanism onto its crank arm linkage part tightly against one another during repositioning their connection between them except where there is contact at these surfaces along such rotation direction without permitting relative movement along said axis slightly away from this location relative thereto; aligning keyway slot spring downward slide latch tightening fastener holding area front face stop underneath one inch ramp resting above outer surface releasing pressure momentarily so that link unit can be moved upwards down into proper engagement tightness between teeth both gears or whatever other type device power transfer employed particular instance; turn latches closed windows positioned slots shown figure placed above tighten pull there again ensuring firmly seated at either end holes because not securely tightened leakage might occur leading corrosion internal damage caused liquids penetrating through said members said control train under increased loads than what should really happen keep any droplets from coming out after carrying out job based on guidelines prescribed automaker examples include: while engine running-set gaps on valves; determine whether or not worn out need replacement any components like bearings seals gaskets rings bushings springs belts plugs filters lubricants coolants solvents adhesives paints varnishes coatings lacquers etc. Then put on the protective cap again.
