How to remove and install the oil pan on Cadillac ElDorado and Fleetwood?

To remove and install the oil pan on 4.5L and 4.9L engines, start by disconnecting the negative battery cable and raising the vehicle. Drain the crankcase and remove the torque converter/flywheel covers from the transaxle. On certain models, remove the exhaust crossunder pipe and reposition it. Then, remove the oil pan-to-engine bolts and the oil pan itself. Clean the gasket mounting surfaces and apply a ¼ inch bead of RTV at the rear main bearing cap and front cover to block joints. Install the oil pan and tighten the bolts to 14 ft. lbs. (18 Nm). Reinstall the exhaust crossunder pipe and the torque converter/flywheel covers. Lower the vehicle, fill the crankcase, and reconnect the negative battery cable. For the 4.6L engine, start by removing the engine assembly and placing it on a stand. Drain the engine oil and remove the 13 oil pan bolts to take off the oil pan. If the oil pan gasket is not damaged, it can be reused, but do not remove it from the oil pan groove unless replacement is necessary. Install a new oil pan seal if required, starting by placing the seal into the pan groove and working it in both directions. Position the oil pan to the crankcase and install the 13 retaining bolts, tightening them to 9 ft. lbs. (10 Nm) in the specified sequence. Finally, reinstall the engine assembly and fill the crankcase with oil.

Genuine Cadillac Fleetwood Oil Pan

Oil Drain Pan

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Oil Pans found

View related parts
Cadillac Fleetwood Pan,Oil
Part Number: 12557557
$100.39 MSRP: $157.97
You Save: $57.58 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil
- Replaces: 12524503, 12527743
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1996 Cadillac Fleetwood | BROUGHAM, BROUGHAM 4 DOOR | 8 Cyl 5.7L
View related parts
Cadillac Fleetwood Pan,Automatic Transmission Oil
Part Number: 8657035
Product Specifications
- Other Name: PAN, Transmission Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1986 Cadillac Fleetwood | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR RWD, BROUGHAM 4 DOOR, BROUGHAM 4 DOOR RWD, FORMAL LIMOUSINE, LIMOUSINE | 6 Cyl 4.1L, 8 Cyl 4.1L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel, 8 Cyl 6.0L
View related parts
Cadillac Fleetwood Pan,Automatic Transmission Oil
Part Number: 8679995
Product Specifications
- Other Name: PAN, Transmission Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986 Cadillac Fleetwood | BROUGHAM 4 DOOR RWD | 8 Cyl 4.1L, 8 Cyl 5.0L
View related parts
Cadillac Fleetwood Pan,Oil
Part Number: 25522386
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Replaces: 12360301
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982 Cadillac Fleetwood | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 6 Cyl 4.1L
View related parts
Cadillac Fleetwood Pan Assembly, Oil (Complete)
Part Number: 3538466
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1992 Cadillac Fleetwood | 2 DOOR, 4 DOOR, 60 SPECIAL 4 DOOR, BROUGHAM 2 DOOR FWD, BROUGHAM 4 DOOR FWD, CONVERSION, FUNERAL COACH, LIMOUSINE 4 DOOR, LIMOUSINE 4 DOOR CTR PART, TOURING 4 DOOR | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Fleetwood Pan Assembly, Oil
Part Number: 555137
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986 Cadillac Fleetwood | BROUGHAM 4 DOOR RWD | 8 Cyl 5.0L
View related parts
Cadillac Fleetwood Pan Assembly, Oil
Part Number: 1622872
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Cadillac Fleetwood | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR RWD, BROUGHAM 4 DOOR, BROUGHAM 4 DOOR RWD, FORMAL LIMOUSINE, LIMOUSINE | 8 Cyl 4.1L

Cadillac Fleetwood Oil Pan

Cadillac Fleetwood automobiles' Oil Pan is part of the engine lubrication system, and it holds the oil that is vital for the proper functioning of the engine. In wet sump system, the engine oil is gathered at the oil pan section and then sucked by the oil pump and used to slick the parts of the engine that are in motion. This design makes it possible for the engine to get adequate lubrication irrespective of the kind of operation it is set for. The oil pans of most vehicles were made by stamped steel up to a certain period in the past; however, Cadillac Fleetwood vehicles might have cast aluminum oil pans in the present day due to the increased durability and efficiency of the metal. In summary, this particular component named oil pan is significantly important in the maintenance of the overall performance and life of the engine in Cadillac Fleetwood vehicles.

Each OEM Cadillac Fleetwood Oil Pan we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Cadillac Fleetwood Oil Pan Parts Questions & Experts Answers

Pan,Oil
12557557
Q: How to remove and install the oil pan on Cadillac ElDorado and Fleetwood?
A: To remove and install the oil pan on 4.5L and 4.9L engines, start by disconnecting the negative battery cable and raising the vehicle. Drain the crankcase and remove the torque converter/flywheel covers from the transaxle. On certain models, remove the exhaust crossunder pipe and reposition it. Then, remove the oil pan-to-engine bolts and the oil pan itself. Clean the gasket mounting surfaces and apply a ¼ inch bead of RTV at the rear main bearing cap and front cover to block joints. Install the oil pan and tighten the bolts to 14 ft. lbs. (18 Nm). Reinstall the exhaust crossunder pipe and the torque converter/flywheel covers. Lower the vehicle, fill the crankcase, and reconnect the negative battery cable. For the 4.6L engine, start by removing the engine assembly and placing it on a stand. Drain the engine oil and remove the 13 oil pan bolts to take off the oil pan. If the oil pan gasket is not damaged, it can be reused, but do not remove it from the oil pan groove unless replacement is necessary. Install a new oil pan seal if required, starting by placing the seal into the pan groove and working it in both directions. Position the oil pan to the crankcase and install the 13 retaining bolts, tightening them to 9 ft. lbs. (10 Nm) in the specified sequence. Finally, reinstall the engine assembly and fill the crankcase with oil.