Should new lifters always be installed when replacing the camshaft in V8 engine on Cadillac Escalade?

If the camshaft is being replaced, always install new Lash Adjusters as well, as old Lash Adjusters should not be used on a new camshaft. The manufacturer states that the engine should be removed for this procedure. Begin by having the air conditioning system discharged by a technician, then relieve the fuel system pressure and disconnect the negative battery terminal. Remove the radiator, air conditioning condenser, and auxiliary automatic transmission fluid cooler if equipped. Disconnect the power steering cooler and move it aside if equipped, then remove the valve covers, intake manifold, rocker arms, pushrods, timing chain, camshaft position actuator, and cylinder heads. Before removing the Lash Adjusters, store them in a clearly labeled box to ensure they are reinstalled in their original locations. Remove the Lash Adjuster retainers and Lash Adjusters, ensuring they are stored cleanly, and do not attempt to withdraw the camshaft with the Lash Adjusters in place. If the Lash Adjusters are stuck due to gum and varnish, special tools may be required for extraction, although newer engines may allow for easier removal. Avoid using pliers on Lash Adjusters unless they are to be replaced, as this can damage them. Remove the bolts and camshaft retainer plate, noting the orientation, then thread a bolt into the camshaft sprocket bolt hole for easier removal. Carefully pull the camshaft out while supporting it near the block to prevent damage to the bearings. Measure the camshaft lobe height and base circle to determine lobe lift, recording the figures for future reference. After cleaning the camshaft, inspect the bearing journals for wear and damage, and measure them with a micrometer. Check the camshaft lobes for discoloration and wear; if they are in good condition, the camshaft can be reused. Clean the Lash Adjusters thoroughly and check for wear, ensuring that used roller Lash Adjusters cannot be reinstalled with a new camshaft. Always use new Lash Adjusters with a new camshaft. Lubricate the camshaft bearing journals and lobes with assembly lube before sliding the camshaft into the engine, taking care not to damage the bearings. Apply thread-locking compound to the camshaft retainer bolts and allow it to cure before installation. Position the camshaft correctly, install the thrust plate, and tighten the bolts to the specified torque. Install the timing chain and sprockets, as well as the camshaft position sensor with a new O-ring. Lubricate the Lash Adjusters with clean engine oil and install them in the retainers, ensuring proper alignment. Finally, complete the installation in reverse order, and before starting the engine, refill the cooling system, change the oil, and install a new oil filter.

Genuine Cadillac Escalade Camshaft

Cam

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Camshafts found

View related parts
Cadillac Escalade Camshaft Asm
Part Number: 12629512
$171.96 MSRP: $236.42
You Save: $64.46 (28%)
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT, Engine; Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Cadillac Escalade | 1/2 TON, 1500 4 DOOR, 1500 4 DOOR SUV, 1500 4 DOOR UTILITY, 1500 CREW CAB, 1500 CREW CAB STANDARD BOX, 4 DOOR 1/2 TON, CLASSIC 1500 CREW CAB LONG BOX, CLASSIC 1500 EXTENDED CAB STANDARD BOX | 8 Cyl 6.2L
View related parts
Cadillac Escalade Camshaft Asm
Part Number: 12612273
$414.70 MSRP: $721.78
You Save: $307.08 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT, Engine; Camshaft
- Replaces: 12583227
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2008 Cadillac Escalade | 1/2 TON, EXT 1/2 TON, YUKON XL/DENALI XL/ESCALADE ESV, YUKON/DENALI/ESCALADE | 8 Cyl 6.2L
View related parts
Cadillac Escalade Camshaft,Engine
Part Number: 12560967
$437.16 MSRP: $760.85
You Save: $323.69 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT, Engine; Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Cadillac Escalade | 1/2 TON, EXT 1/2 TON, EXT 3/4 TON, YUKON/DENALI/ESCALADE | 8 Cyl 5.3L
View related parts
Cadillac Escalade Camshaft Asm
Part Number: 12561721
$437.16 MSRP: $760.85
You Save: $323.69 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT, Engine; Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Cadillac Escalade | 1/2 TON, 3/4 TON, EXT 1/2 TON, EXT 3/4 TON, YUKON/DENALI/ESCALADE | 8 Cyl 6.0L
View related parts
Cadillac Escalade Camshaft Asm
Part Number: 12664572
$141.01 MSRP: $222.88
You Save: $81.87 (37%)
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Cadillac Escalade | YUKON XL/DENALI XL/ESCALADE ESV | 8 Cyl 6.2L
View related parts
Cadillac Escalade Camshaft Asm
Part Number: 12623066
$229.60 MSRP: $399.56
You Save: $169.96 (43%)
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT, Engine; Camshaft
- Replaces: 12617374
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2014 Cadillac Escalade | 1/2 TON, EXT 1/2 TON, YUKON XL/DENALI XL/ESCALADE ESV, YUKON/DENALI/ESCALADE | 8 Cyl 6.2L Flex
View related parts
Cadillac Escalade CAMSHAFT ASM
Part Number: 12664911
$107.09 MSRP: $186.34
You Save: $79.25 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Replaced by: 12723516
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2022-2024 Cadillac Escalade | 1/2 TON, YUKON XL/DENALI XL/ESCALADE ESV | 8 Cyl 5.3L
View related parts
Cadillac Escalade CAMSHAFT ASM
Part Number: 12664912
$115.84 MSRP: $201.57
You Save: $85.73 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Cadillac Escalade | 1/2 TON, YUKON XL/DENALI XL/ESCALADE ESV, YUKON/DENALI/ESCALADE | 8 Cyl 6.2L
View related parts
Cadillac Escalade Camshaft Asm
Part Number: 12629698
$199.88 MSRP: $347.85
You Save: $147.97 (43%)
ADD TO CART
Product Specifications
- Other Name: CAMSHAFT, Engine; Camshaft
- Replaces: 12612275
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Cadillac Escalade | YUKON/DENALI/ESCALADE | 8 Cyl 6.0L, 8 Cyl 6.0L Flex
View related parts
Cadillac Escalade CAMSHAFT ASM,OVERHEAD VLV
Part Number: 12711967
$364.99 MSRP: $635.25
You Save: $270.26 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Replaces: 12617373, 12623065
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009 Cadillac Escalade | 1/2 TON, EXT 1/2 TON, YUKON XL/DENALI XL/ESCALADE ESV, YUKON/DENALI/ESCALADE | 8 Cyl 6.2L Flex
View related parts
Cadillac Escalade Camshaft Assembly, Exh
Part Number: 55508605
$84.02 MSRP: $132.16
You Save: $48.14 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Cadillac Escalade | 1/2 TON, YUKON XL/DENALI XL/ESCALADE ESV, YUKON/DENALI/ESCALADE | 6 Cyl 3.0L Diesel
View related parts
Cadillac Escalade Camshaft Assembly, Int
Part Number: 55508606
$85.98 MSRP: $135.25
You Save: $49.27 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Cadillac Escalade | 1/2 TON, YUKON XL/DENALI XL/ESCALADE ESV, YUKON/DENALI/ESCALADE | 6 Cyl 3.0L Diesel
View related parts
Cadillac Escalade Camshaft Asm
Part Number: 12556291
$328.83 MSRP: $519.71
You Save: $190.88 (37%)
Product Specifications
- Other Name: CAMSHAFT, Engine; Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Cadillac Escalade | 3/4 TON, EXT 3/4 TON
View related parts
Cadillac Escalade Camshaft Asm
Part Number: 12583623
$241.36 MSRP: $381.48
You Save: $140.12 (37%)
Product Specifications
- Other Name: CAMSHAFT, Engine; Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Cadillac Escalade | 1/2 TON, EXT 1/2 TON, YUKON/DENALI/ESCALADE | 8 Cyl 5.3L
View related parts
Cadillac Escalade Camshaft
Part Number: 98077453
$476.38 MSRP: $756.33
You Save: $279.95 (38%)
Product Specifications
- Other Name: CAMSHAFT, Engine
- Replaces: 97211770
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Cadillac Escalade | 3/4 TON, EXT 3/4 TON
View related parts
Cadillac Escalade Camshaft,Engine
Part Number: 10241264
Product Specifications
- Other Name: CAMSHAFT, Engine; Camshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | 1 TON CREW CAB, 1/2 TON, 3/4 TON, 4 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON, CREW CAB 1 TON, EXTENDED CAB 1 TON, EXTENDED CAB 6'6" BOX 1/2 TON, EXTENDED CAB 6'6" BOX 3/4 TON, EXTENDED CAB 8' BOX 3/4 TON, K2500 CREW CAB, K3500 CAB CHASSIS 135.5, K3500 CAB CHASSIS 159.9, REGULAR CAB 1 TON, REGULAR CAB 3/4 TON, YUKON/DENALI/ESCALADE | 8 Cyl 5.7L

Cadillac Escalade Camshaft

In Cadillac Escalade cars, the camshaft is crucial since it regulates the opening and closing of the engine's intake and exhaust valves to allow the air/fuel blend into the cylinder and release exhaust gases. Usually made of iron or steel material, Cadillac Escalade camshaft work through Over Head Valve (OHV), Single Over Head Cam (SOHC), and Double Over Head Cam (DOHC), and so on, these models contribute to different engine performance. Some of key characteristics of camshaft include Lift, duration, and lobe separation angle these are paramount in determination of power produce by Cadillac Escalade camshaft and the quality of its idle. Performance camshafts work on improving airflow and power not just in terms of low-end ones, especially at high rpm, and enable all sorts of modifications depending on changes desired.

Each OEM Cadillac Escalade Camshaft we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Cadillac Escalade Camshaft Parts Questions & Experts Answers

Camshaft Asm
12629512
Q: Should new lifters always be installed when replacing the camshaft in V8 engine on Cadillac Escalade?
A: If the camshaft is being replaced, always install new Lash Adjusters as well, as old Lash Adjusters should not be used on a new camshaft. The manufacturer states that the engine should be removed for this procedure. Begin by having the air conditioning system discharged by a technician, then relieve the fuel system pressure and disconnect the negative battery terminal. Remove the radiator, air conditioning condenser, and auxiliary automatic transmission fluid cooler if equipped. Disconnect the power steering cooler and move it aside if equipped, then remove the valve covers, Intake Manifold, Rocker Arms, Pushrods, Timing Chain, camshaft position actuator, and cylinder heads. Before removing the Lash Adjusters, store them in a clearly labeled box to ensure they are reinstalled in their original locations. Remove the Lash Adjuster retainers and Lash Adjusters, ensuring they are stored cleanly, and do not attempt to withdraw the camshaft with the Lash Adjusters in place. If the Lash Adjusters are stuck due to gum and varnish, special tools may be required for extraction, although newer engines may allow for easier removal. Avoid using pliers on Lash Adjusters unless they are to be replaced, as this can damage them. Remove the bolts and camshaft retainer plate, noting the orientation, then thread a bolt into the camshaft sprocket bolt hole for easier removal. Carefully pull the camshaft out while supporting it near the block to prevent damage to the bearings. Measure the camshaft lobe height and base circle to determine lobe lift, recording the figures for future reference. After cleaning the camshaft, inspect the bearing journals for wear and damage, and measure them with a micrometer. Check the camshaft lobes for discoloration and wear; if they are in good condition, the camshaft can be reused. Clean the Lash Adjusters thoroughly and check for wear, ensuring that used roller Lash Adjusters cannot be reinstalled with a new camshaft. Always use new Lash Adjusters with a new camshaft. Lubricate the camshaft bearing journals and lobes with assembly lube before sliding the camshaft into the engine, taking care not to damage the bearings. Apply thread-locking compound to the camshaft retainer bolts and allow it to cure before installation. Position the camshaft correctly, install the thrust plate, and tighten the bolts to the specified torque. Install the timing chain and sprockets, as well as the camshaft position sensor with a new O-ring. Lubricate the Lash Adjusters with clean engine oil and install them in the retainers, ensuring proper alignment. Finally, complete the installation in reverse order, and before starting the engine, refill the cooling system, change the oil, and install a new oil filter.