How do you remove the Crankshaft Damper?

To remove the 4.5 L engine, the first step is to disconnect the negative battery cable and take off the serpentine belt. Then, lift up and support the vehicle properly before removing the right front wheel and tire. Take away the right front air deflector as well as support car body- strut at right side and support engine cradle's right side. Lower the cradle on its right hand side and remove the balancer bolt together with washer of harmonic. Using puller, take off balancer.To install an engine, put lubricant between hub and seal using EP lube; then position balancer on crankshaft aligning key slot in hub w/key on crankshaft; bottom hub out on crankshaft using installer tool& install harmonics bolt & washer at that point lighten it to 60 ft lb Raise cradle's right side & raise while positioning ball joint to steering knuckle While raising, support body &right side of engn cradls & insert bolts in itInstall R/Front A/Defl., R/Front Whl/Tire, lower Veh Finally connect Negative-batt cable For 4.9L engine same procedure but tightens harmonic balancer bolt at 70 ft lb For 4.6L Engine unhook negative battery cable; release tension from accessory drive beltOn jack stands raise vehicle-Remove Right Front Wheel-Remove splash shields & brace Support eng cradle remove bolts on R/Side Disconnect RSS sensor use flywheel holder tool to takeout balancer bolt Lower eng cradle install pilot tool into crankshaft Use puller tool to remove hb To install put balancer on crankshaft , use a tool to get HB through Clean hbolt threads tighten it 105 ft-lbs +120 degrees Raise englcradle insb then reconnect suspension position sensors Remove flywheel holder t/install oil pan-t/transmission brace Install Wheelhouse splash shields and Right front wheel Lower vehicle install accessory drive belt Finally connect negative battery cable.

Genuine Cadillac Eldorado Harmonic Balancer

Engine Harmonic Balancer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Harmonic Balancers found

View related parts
Cadillac Eldorado Balancer Asm,Crankshaft
Part Number: 88960257
Product Specifications
- Other Name: BALANCER, Engine Crankshaft And Camshaft Balancer
- Replaces: 12552436
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1993 Cadillac Eldorado | COMMERCIAL CHASSIS, ELDORADO | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Eldorado Pulley Assembly, (3 Groove 7.320 Pd)
Part Number: 560328
Product Specifications
- Other Name: PULLEY, Engine Crankshaft And Camshaft Balancer; Pulley
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Cadillac Eldorado | BIARRITZ, COMMERCIAL CHASSIS, ELDORADO | 8 Cyl 5.7L Diesel
View related parts
Cadillac Eldorado Pulley,Crankshaft
Part Number: 25522581
Product Specifications
- Other Name: PULLEY, Engine Crankshaft And Camshaft Balancer; Pulley
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982 Cadillac Eldorado | ELDORADO | 6 Cyl 4.1L
View related parts
Cadillac Eldorado Balancer Assembly, Crankshaft
Part Number: 12552437
Product Specifications
- Other Name: BALANCER, Engine Crankshaft And Camshaft Balancer
- Replaces: 01647168, 1647168
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1999 Cadillac Eldorado | COMMERCIAL CHASSIS, ELDORADO | 8 Cyl 4.6L
View related parts
Cadillac Eldorado Balancer Assembly, Crankshaft
Part Number: 12557707
Product Specifications
- Other Name: BALANCER, Engine Crankshaft And Camshaft Balancer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2002 Cadillac Eldorado | ELDORADO | 8 Cyl 4.6L
View related parts
Cadillac Eldorado Balancer Kit,Crankshaft
Part Number: 25523502
Product Specifications
- Other Name: BALANCER; Vibration Damper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982 Cadillac Eldorado | ELDORADO | 6 Cyl 4.1L
View related parts
Cadillac Eldorado Balancer
Part Number: 3517492
Product Specifications
- Other Name: DAMPER, Engine Crankshaft And Camshaft Balancer; Damper, Pulley, Vibration Damper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Cadillac Eldorado | BIARRITZ, COMMERCIAL CHASSIS, ELDORADO | 8 Cyl 4.1L

Cadillac Eldorado Harmonic Balancer

A Harmonic Balancer in Cadillac Eldorado automative play an important part in the balancing of an engine and absorbing vibration resultant from combustion. This component is commonly known as a vibration damper and it made up of a metal hub, which is fitted onto the crankshaft, with the restraining ring being a thick metal inertia ring with an integral rubber ring spacer to give flexibility. This design aim at reducing the torsion effect of the crank shaft so as to make the engine to run in a smooth manner. In the current and earlier now models of Eldorado several types of harmonic balancers have been installed such as conventional construction, viscous fluid balancers and tunable multi-piece construction balancers. Standard OEM balancers are suitable when the engine was tuned at the factory; performance balancers are available for the engines, to protect against higher vibration and rpm levels. These options of performance has been developed to the greatest satisfaction where needs meet safety measure in their operation thereby making them reliable under most circumstances.

Each OEM Cadillac Eldorado Harmonic Balancer we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Cadillac Eldorado Harmonic Balancer Parts Questions & Experts Answers

Balancer Asm,Crankshaft
88960257
Q: How do you remove the Crankshaft Damper?
A: To remove the 4.5 L engine, the first step is to disconnect the negative battery cable and take off the serpentine belt. Then, lift up and support the vehicle properly before removing the right front wheel and tire. Take away the right front air deflector as well as support car body- strut at right side and support engine cradle's right side. Lower the cradle on its right hand side and remove the balancer bolt together with washer of harmonic. Using puller, take off balancer.To install an engine, put lubricant between hub and seal using EP lube; then position balancer on crankshaft aligning key slot in hub w/key on crankshaft; bottom hub out on crankshaft using installer tool& install harmonics bolt & washer at that point lighten it to 60 ft lb Raise cradle's right side & raise while positioning ball joint to steering knuckle While raising, support body &right side of engn cradls & insert bolts in itInstall R/Front A/Defl., R/Front Whl/Tire, lower Veh Finally connect Negative-batt cable For 4.9L engine same procedure but tightens harmonic balancer bolt at 70 ft lb For 4.6L Engine unhook negative battery cable; release tension from accessory drive beltOn jack stands raise vehicle-Remove Right Front Wheel-Remove splash shields & brace Support eng cradle remove bolts on R/Side Disconnect RSS sensor use flywheel holder tool to takeout balancer bolt Lower eng cradle install pilot tool into crankshaft Use puller tool to remove hb To install put balancer on crankshaft , use a tool to get HB through Clean hbolt threads tighten it 105 ft-lbs +120 degrees Raise englcradle insb then reconnect suspension position sensors Remove flywheel holder t/install oil pan-t/transmission brace Install Wheelhouse splash shields and Right front wheel Lower vehicle install accessory drive belt Finally connect negative battery cable.